horizontal/vertical metal cutting bandsaw - Harbor Freight Tools
horizontal/vertical metal cutting bandsaw - Harbor Freight Tools horizontal/vertical metal cutting bandsaw - Harbor Freight Tools
e. Place the new Saw Blade (82) betweeneach of the Guide assembliesand around the Upper Blade Wheel(37) and Lower Blade Wheel (54).IMPORTANT: The teeth must bepointing downward toward theMotor. (See Figure U.)f. NOTE: The Bandsaw is equippedwith a 64” diameter, .025” thick,15/32” wide, 14 teeth per inch SawBlade (82). The machine will alsoaccept Blades in 4, 6, 8, and 10tooth sizes. The choice of Bladepitch is determined by the thicknessof the material to be cut. The thinnerthe workpiece, the more teeth is recommended.A minimum of 3 teethshould engage the workpiece at alltimes for proper cutting.(See Figure U.)CAUTION: If the teeth of the SawBlade are so far apart that theystraddle the workpiece, severedamage to the workpiece and/orSaw Blade will result.g. Tighten the tension on the new SawBlade (82) by turning the Blade TensionKnob (34). (See Figure U.)h. Close the Blade Back Cover (114).(See Figure U.)4. To replace the V-Belt: The Bandsawuses a size 0-506 V-Belt (10).To replace the V-Belt:HEX BOLT(70)SPINDLE PULLEY(1)V-BELT (10)FIGURE VMOTOR PULLEY(79)a. Open the Pulley Cover (72).(See Figure V.)b. Loosen the Hex Bolt (70) to releasetension on the old V-Belt.(See Figure F.)c. Remove the old V-Belt (10) from thetwo Pulleys (1, 79). (See Figure V.)d. Place the new V-Belt (10) into theproper Pulley (1, 79) combination forthe desired Blade speed.(See Figures G and V.)e. Adjust the position of the Motor (81)to obtain approximately 1/2” depressionin the V-Belt (10) when applyingpressure with your thumb.(See Figure V.)f. Tighten the Hex Bolt (70) to securethe Motor (81) in place.(See Figure T.)SKU 93762 For technical questions, please call 1-800-444-3353. Page 22
5.To lubricate the Worm Gear andWorm Shaft: The Worm Gear (17)and Gear Shaft (19) run in an oil bathGear Box and should not require anoil change more than once a year,unless the oil becomes contaminatedor a leak occurs due to improperreplacement of the Gear Box Cover(14). To change oil in the Gear Box:a. Position the Body Frame (60) in thehorizontal position. (See Figure S.)6.To clean the exterior parts of theBandsaw, use only a clean clothand mild detergent or mild solvent toclean the body of the Saw. Do notimmerse any electrical part of themachine in any liquids.PIVOT (120)LOCKING PIN (115)GEAR BOXCOVER (14)GEAR SHAFT(19)HEXBOLT (11)FIGURE X7. When the Bandsaw is not in use orwhen transporting the tool: Alwayslower the Body Frame (60) toits horizontal position and insert theLocking Pin (115) into the Pivot (120)to secure the Body Frame in place.(See Figure X.)FIGURE WWORMGEAR (17)b. Remove the four Hex Bolts (11),Gear Box Cover (14), and Gear BoxGasket (15). (See Figure W.)c. Remove the old oil from inside theGear Box and replace the oil using140 weight gear oil. The newoil should just come to the edge ofthe Gear Box. Do not overfill. (SeeFigure W.)d. Replace the Gear Box Gasket (15),Gear Box Cover (14), and four HexBolts (11). (See Figure W.)8. CAUTION! All maintenance,service, or repairs not mentionedin this manual must only be performedby a qualified service technician.SKU 93762 For technical questions, please call 1-800-444-3353. Page 23
- Page 1 and 2: horizontal/verticalmetal cutting ba
- Page 3 and 4: Save This ManualKeep this manual fo
- Page 5 and 6: 20.21.1.2.3.4.5.6.7.8.or other part
- Page 7 and 8: ditions and situations that may occ
- Page 9 and 10: SPECIFICATIONSMotor120 V~ / 60 Hz /
- Page 11 and 12: To Attach The Pulley Cover:WORMSHAF
- Page 13 and 14: SMALL VERTICAL CUTTING PLATE (194)V
- Page 15: AdjustmentsTo Adjust The Stock Stop
- Page 18 and 19: Basic Bandsaw Operation --Vertical
- Page 20 and 21: Blade into the workpiece. (See Figu
- Page 24 and 25: TROUBLESHOOTINGSKU 93762 For techni
- Page 26 and 27: Part # Description Qty80 Motor Pull
- Page 28 and 29: ASSEMBLY DIAGRAM194: Vertical Cutti
5.To lubricate the Worm Gear andWorm Shaft: The Worm Gear (17)and Gear Shaft (19) run in an oil bathGear Box and should not require anoil change more than once a year,unless the oil becomes contaminatedor a leak occurs due to improperreplacement of the Gear Box Cover(14). To change oil in the Gear Box:a. Position the Body Frame (60) in the<strong>horizontal</strong> position. (See Figure S.)6.To clean the exterior parts of theBandsaw, use only a clean clothand mild detergent or mild solvent toclean the body of the Saw. Do notimmerse any electrical part of themachine in any liquids.PIVOT (120)LOCKING PIN (115)GEAR BOXCOVER (14)GEAR SHAFT(19)HEXBOLT (11)FIGURE X7. When the Bandsaw is not in use orwhen transporting the tool: Alwayslower the Body Frame (60) toits <strong>horizontal</strong> position and insert theLocking Pin (115) into the Pivot (120)to secure the Body Frame in place.(See Figure X.)FIGURE WWORMGEAR (17)b. Remove the four Hex Bolts (11),Gear Box Cover (14), and Gear BoxGasket (15). (See Figure W.)c. Remove the old oil from inside theGear Box and replace the oil using140 weight gear oil. The newoil should just come to the edge ofthe Gear Box. Do not overfill. (SeeFigure W.)d. Replace the Gear Box Gasket (15),Gear Box Cover (14), and four HexBolts (11). (See Figure W.)8. CAUTION! All maintenance,service, or repairs not mentionedin this manual must only be performedby a qualified service technician.SKU 93762 For technical questions, please call 1-800-444-3353. Page 23