Manual - Building Block Video CCTV

More documents

Recommendations

Info

3. INSTALLATIONOPERATING VOLTAGEThe Rx400DC requires all connections to the PCB to be made by the installer, and via terminal blocks or byplug and socket. These connections are: power in, video in, video out, alarm in, alarm out, pan, tilt, lens,preset and auxiliary outputs. See Fig. 2, page 9 for the correct connections.The Rx400DC is supplied pre-configured to suit the application for which it is intended, i.e. to control a 24VDC-operated panning head or other equipment.The unit is pre-wired as standard for 230 volt mains operation.Options are available at purchase time for 110Vac and 24Vac supply operation.NOTEWith Issue 3 pcbs and Version 18 software, J10 zoom & focus preset inputs are swapped.This is corrected in software version 19.i.e. Issue 3 PCB and V18 softwareZoom preset I/P = J10 Pin 2 (FC)Focus preset I/P = J10 Pin 3 (ZM)Telemetry Receiver Installation HandbookRx400DC2 July 2004 Rev6Page_26
CABLE CONNECTION INSTRUCTIONSFig. 2: Cable connection diagramJ8CABLE ERRORJ6 J8ORANGEGREENBLUEORANGEGREENBLUEORANGEGREENBLUEORANGEGREENBLUEJ6 ALARM INA. IN 87654321LIVEEARTHNEUTRALWIPE LIVEWIPE EARTHWIPE NEUTRALWASH LIVEWASH EARTHWASH NEUTRALLAMPS LIVELAMPS EARTHLAMPS NEUTRALALARM INPUT 8ALARM INPUT 7ALARM INPUT 6ALARM INPUT 5ALARM INPUT 4ALARM INPUT 3ALARM INPUT 2ALARM INPUT 1UNSWITCHEDAUX 3AUX 2AUX 1GNDJ13 TILTON12345VIDEO IN(FROM CAMERA)VIDEO OUT(TO TELEMETRYTRANSMITTER)240VOLTS AC IN(IEC CONNECTOR)GAINLIFTF2F1J2J2F2630mA TF15A T678LENS V INCH VJ10 J13TM -TM +TB -TB +PB -PB +PM -PM +J13 PANJ10 PRESET-TLTPAN+-FCZM+J3GNDA. OUTA. OUTJ3+12GNDTXGNDRXZOOMGNDFOCUSIRIS VGNDT PAIRT PAIRALARM INPUTGROUNDS 1 - 8ALARM OUTALARM OUT+12V DCGROUNDTXGROUNDRXCAMERAPOWERZOOM MOTOR DRIVELENS GROUNDFOCUS MOTOR DRIVETILT BRAKE +PAN BRAKE -PAN BRAKE +PAN MOTOR -PAN MOTOR +RS232 DRIVE FORCAMERAS (OPTIONAL)LENSAUTO-IRIS OVER-RIDE VOLTAGEAUTO-IRIS OVER-RIDE GROUNDTWISTED PAIR TELEMETRYTWISTED PAIR INPUTTILT MOTOR -TILT MOTOR +TILT BRAKE -HEAD PRESET -VE SUPPLYHEAD PRESET TILT WIPERHEAD PRESET PAN WIPERHEAD PRESET +VE SUPPLYLENS PRESET -VE SUPPLYZOOM PRESET WIPERFOCUS PRESET WIPERLENS PRESET +VE SUPPLYTelemetry Receiver Installation HandbookRx400DC2 July 2004 Rev6Page_27
Page 3 and 4: Rx200 mk2AC Left/Right/Wipe/Lights/
Page 5 and 6: Rx200 INSTALLATION INSTRUCTIONSThe
Page 7: LAUNCH AMPLIFIERThere are two varia
Page 12 and 13: LAUNCH AMPLIFIERThere are two varia
Page 15: 0222586GCo-Ax Cable (Minimum Specif
Page 18 and 19: CABLE CONNECTIONS FOR Rx400P UNITSC
Page 20 and 21: SW8(on/off) Start Self Test - LEFT,
Page 22 and 23: 1. PRE-INSTALLATION CHECKS AND SAFE
Page 24 and 25: Auto-Iris Output:Video Input:Video
Page 28 and 29: 4. SETUPDIAGNOSTIC AIDSTwo L.E.D.
Page 30 and 31: PROGRAMMING THE UNITProgramming is
Page 32 and 33: SETTINGS FOR NORMAL OPERATIONSevera
Page 34 and 35: INSTALLATION INSTRUCTIONS FOR PCB-B
Page 36 and 37: BBV TX1500 exampleBuilding Block Vi
Page 38 and 39: - This page is blank for your notes
Page 40: The BBV product range.Product Descr

Manual - Building Block Video CCTV

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?