friction clutches - Arten Freios e Embreagens Industriais

Table of Contents◗ MISALIGNMENT TABLESFriction Clutches“Air Champ” ®The following table and drawing represents misalignment capabilitiesfor Dodge Taper-Lock Poly Disc Couplings. The values are based uponthe coupling maximum capability for individual misalignment.These tabulated values may not be combined. Review the drawing andthe table for information regarding the Clutch and application.Dodge Taper-Lock Poly Disc CouplingsMeasured Variation at Points 180 degrees ApartAxial FloatMaximumValue fromCoupling Parallel Angular recommendedClutch Size Maximum Maximum Initial SpacingModel (In) (In) (In) (In)F-450 2.625 0.015 0.040 ' +0.125L-600 4.000 0.015 0.064 ' +0.125M-800 7.000 0.015 0.112 ' +0.125H-1000 8.000 0.015 0.128 ' +0.125XHW 10.000 0.015 0.160 ' +0.188Clutch-Brakes, Thru-Shaft MountedThe following table and drawing represents misalignment capabilitiesfor Dodge Taper-Lock Poly Disc Couplings. The values are based uponthe coupling maximum capability for individual misalignment. Thesetabulated values may not be combined. Review the drawing and thetable for information regarding the Clutch-Brake and application.Dodge Taper-Lock Poly Disc CouplingsMeasured Variation at Points 180 degrees ApartAxial FloatMaximumValue fromCoupling Parallel Angular recommendedClutch Size Maximum Maximum Initial SpacingModel (In) (In) (In) (In)BWCB N/A N/A N/A N/AFWCB 2.625 0.015 0.040 ± 0.125LWCB 4.000 0.015 0.064 ± 0.125MWCB 7.000 0.015 0.112 ± 0.125HWCB 8.000 0.015 0.128 ± 0.125FCDB 2.625 0.015 0.040 ± 0.125LCDB 4.000 0.015 0.064 ± 0.125MCDB 7.000 0.015 0.112 ± 0.125HCDB 8.000 0.015 0.128 ± 0.1253 A214APPLICATION ENGINEERING DATATooth Clutches (5H), Torque Limiters (TL) andMultiplate Clutches (4H)Flexible CouplingsUse these tables if you are attaching a Flexible Coupling to a ToothClutch (5HP, 5HP-E, 5HP-SP, 5HPSP-E), Multi-Disc Clutch (4HP) orTorque Limiter (TL-A, TL-AE, TL-AC).The following tables represent misalignment capabilities for Single &Double Flex Coupling Assemblies. The values are based upon themaximum capability for individual misalignment.If parallel, angular and axial misalignment are all required, be certainthat the combined percentage of each does not exceed 100%. Forinstance, if 100% of the parallel misalignment rating is required, noangular or axial misalignment is allowed. If 50% of the parallel misalignmentis required, only 50% of the angular misalignment OR 50%of the axial rating will be available.Find the Product Number of the Flexible Coupling you are using inyour application and take note of the misalignment values allowed.Single Flexible CouplingsProduct Angular Axial ParallelNumber (Degrees) (In) (In)909980 1.5 0.065 0.011910080 1.5 0.070 0.012910180 1.5 0.080 0.013910280 1.5 0.090 0.014910380 1.5 0.105 0.017910480 1.5 0.120 0.019910580 1.5 0.135 0.022911780 1.5 0.155 0.026Double Flexible CouplingsProduct Angular Axial ParallelNumber (Degrees) (In) (In)909981 3.0 0.130 0.063910081 3.0 0.140 0.078910181 3.0 0.160 0.085910281 3.0 0.180 0.091910381 3.0 0.210 0.104910481 3.0 0.240 0.117910581 3.0 0.270 0.137911781 3.0 0.310 0.170D R I V E NS H A F TD R I V I N GS H A F TA N G U L A R M E A S U R E M E N T :E - A = A N G U L A R T O L E R A N C EP A R A L L E L ( M U S T B E L E S S T H A N " A N G U L A R M A X I M U M ")M E A S U R E M E N T ETo Order Coupling Type Clutch — Specify1. Product Number of Pilot Mount Unit2. Coupling Half (includes Dodge coupling half, Poly-Disc & adapter)D0317393. Taper Lock Bushing4. Shaft Extension/Sleeve Bushing(if needed)**Same length as clutch.◗ STANDARD KEY SIZESShaft Size (In)Min MaxKey Size.500 .562 .125 x .125.625 .875 .187 x .187.937 1.25 .250 x .2501.312 1.375 .312 x .3121.437 1.75 .375 x .3751.812 2.25 .500 x .500Shaft Size (In)Min MaxKey Size2.312 2.75 .625 x .6252.812 3.25 .750 x .7503.187 3.75 .875 x .8753.812 4.50 1.00 x 1.004.562 5.50 1.25 x 1.255.562 6.50 1.50 x 1.50369