SAM4s SPS-500 series programming manual.pdf

More documents

Recommendations

Info

Define PortThere are 4 serial ports and one Ethernet port for peripheral device connection. The following section definesthe peripheral device and the parameters for the peripheral that will be attached to the port.► Select DEFINE PORT from the S mode PROGRAMMING MENU.Define Port - DefinitionsPORTThis is the number of the physical port located on the ECR. There are four serial ports, and an Ethernetport (with settings for up to seven Ethernet printers).PORT DESCRIPTIONThis is an area in which you can type your own description of the task the port is carrying out, i.e.KITCHEN PRINTER, HAND SCANNER etc. This description is for your own reference purposes.BAUD RATEThis is the Baud Rate of the device, the communications speed of the peripheral.PARITYThis is a standard peripheral definition; the information is normally supplied with the device.DATA BITSThis is a standard peripheral definition; the information is normally supplied with the device.STOP BITSThis is a standard peripheral definition; the information is normally supplied with the device.RETRIESThis is the number of attempts that will be made to communicate with a device before failure is declared.The default setting (3) is satisfactory for most commonly used peripherals.PRINT BIT MAPThis allows printing of the previously downloaded graphics logo if the option has been defined asavailable within the memory allocation.FEED LINES BEFORE PRINTING/AFTER PRINTINGThis the number of lines to be fed before or after the printing is started, this will make the receipt longer,helping format the ticket for non-cutter printers.LOGO SIZESelect Normal, Double Height, Double Width, or Quadruple. This option is not used when using the newNV image downloading.LINES ON HARD SLIPWhen a slip printer is used, this is the number of lines that can be printed on a loose paper printer, beforea prompt for the next page appears.60 S Mode Programming SPS-500 Program Manual v1.13
CUTTING AFTER PRINTINGWhen a printer has the capabilities of auto cut, this option will decide if that feature is to be used. Forreceipts it is commonly set to yes, however detail journal printers do not require this option.IN CASE OF PRINTER, KICK THE DRAWERUse to send an audible beep using an optional beeper.PRINT UPSIDE DOWNThe printer will print the receipt upside down so that if the printer is wall-mounted, or placed vertically,the user can read easily. Supported printers are: SAM4s Ellix 10, Ellix 20, Bixolon SRP-350, EpsonTM-T88-2. If the number of lines to print in one print job exceeds 1000, the SPS-500 will ignore theoption.DEVICEThis is the peripheral that will be connected to the port. The following options can be chosen:DISABLEThe port is not activePRINTERThe port will be used to operate a printer, you are then presented with a list of Printer types, all ofwhich are pre-programmed with Driver setting.VIDEOThis is a linked Kitchen Video System for the display of products.POLLINGThis is the on-line computer link.SCALEThis links to an approved scale for weighted items. The “OZ Scale” setting supports the Avery Berkel6712 POS scale, and the POS30/POS60 scales which are capable of weighing in ounces (rather thanpounds). NOTE: If weighing by ounces, the price per ounce must be preset in the PLU price. Thescale will weigh in ounces and compute the correct price per ounce.SCANNERThis option enables a barcode scanner.EFT TERMINALThis option links a DataTran integrated payment device.CHANGERThis option allows a coin changer to be connected.POLE DISPLAYThis option allows a pole display to be connected.LIQUORThis option allows a liquor dispenser to be connected.PDCThe option enables a peripheral device controller.SPS-500 Program Manual v1.13 S Mode Programming 61
Page 4 and 5:
1-2 Servicing PrecautionsWARNING: F
Page 6 and 7:
Memory Clearing....................
Page 8 and 9:
8 Contents SPS-500 Program Manual
Page 10 and 11: Safe OperationDo not locate your SA
Page 12 and 13: Controls & ConnectionsThe Power LED
Page 14 and 15: Connection PanelStandard ports incl
Page 16 and 17: Default Screen LayoutMain ScreenUp
Page 18 and 19: P Mode Main MenuNote: P Mode Menu b
Page 20 and 21: Custom Screen LayoutsAfter your aut
Page 22 and 23: 6. The display will monitor the mem
Page 24 and 25: Required Support ResourcesA PC with
Page 26 and 27: Diagnostics/Functions Available for
Page 28 and 29: Application Upgrade/Backup from SD/
Page 30 and 31: Capturing SPS-500 ScreensEquipment
Page 32 and 33: Image Download Using SD Memory Card
Page 35 and 36: S Mode ProgrammingS- Mode Programmi
Page 37 and 38: KEYBOARD TESTThis will test the key
Page 39 and 40: Memory AllocationCAUTION: The proce
Page 41 and 42: (16) PROJECTIONSThe Product Project
Page 43 and 44: Key Relocation Screen—Screen Tab1
Page 45 and 46: Key Relocation Screen—Design TabS
Page 47 and 48: 145 MODIFIER 10146 Reserved147 #/NO
Page 49 and 50: EMPLOYEE (1-10) 041-050The EMPLOYEE
Page 51 and 52: PAID OUT 1-5 151-155Touch a PAID OU
Page 53 and 54: TAX SHIFT 1-6 225-230Use to shift t
Page 55 and 56: System OptionsThis section is used
Page 57 and 58: Select SERIAL or ETHERNET.PC CONNEC
Page 59: Printer Driver SelectionsThis progr
Page 63 and 64: Password NotesThe correct password
Page 65 and 66: 4. The SRAM BACKUP (SD) dialog box
Page 67 and 68: FTP TransmissionChoose FTP Transmis
Page 69 and 70: P Mode ProgrammingP Mode Programmin
Page 71 and 72: PLU Add & Change1. From the P mode
Page 73 and 74: PRODUCT MIX #1This works in-conjunc
Page 75 and 76: PLU Status GroupPLU Status Groups a
Page 77 and 78: (16) STOCK PLU?Choose Yes if you wi
Page 79 and 80: (42) ELIGIBLE FOR CANADIAN DONUT LA
Page 81 and 82: NON-PLU Code Field DefinitionsLENGT
Page 83 and 84: Age Verification by Card Swipe(Cali
Page 85 and 86: 3. Once PLUs are added they will be
Page 87 and 88: 10. Touch ADDType the descriptor: C
Page 89 and 90: Format of Automatically Created Scr
Page 91 and 92: PLU GroupGroups are designated to a
Page 93 and 94: Function Key Program SummaryDescrip
Page 95 and 96: DescriptorManagerRequiredHALO(RATE)
Page 97 and 98: DescriptorManagerRequiredHALO(RATE)
Page 99 and 100: Modifier Key Program NotesAFFECT DI
Page 101 and 102: System OptionsOptions are sorted by
Page 103 and 104: (10) ROUNDING SYSTEMUse these optio
Page 105 and 106: (42) BASE CURRENCYSet for local cur
Page 107 and 108: (62) USE STOCK LINK PLU ON PLU PGMC
Page 109 and 110: (9) OPEN DRAWER DURING CASH DECLARA
Page 111 and 112:
(4) SELECT HELD ITEMS ON RECALLItem
Page 113 and 114:
(5) COMBINE LIKE ITEMS ON KP OR KVS
Page 115 and 116:
(8) DISPLAY RUNNING SUBTL ON POLEAl
Page 117 and 118:
(33) NOT PRINT AN ALPHA TEXT MESSAG
Page 119 and 120:
Report Options(1) ONLY TTL ON PRODU
Page 121 and 122:
If Yes, the percentage entered here
Page 123 and 124:
EmployeeThe employee file contains
Page 125 and 126:
EDIT JOB CODESNote: An employee wit
Page 127 and 128:
(30) ALLOW PLU QUICK REGISTER?(31)
Page 129 and 130:
ReportsUse this program to create a
Page 131 and 132:
TimeTime period definitions and tim
Page 133 and 134:
Product & IngredientNOTE: Be carefu
Page 135 and 136:
Product Mix Group Time PeriodsMemor
Page 137 and 138:
# OF NON-REPEAT BREAKSEnter the num
Page 139 and 140:
NO. DESCRIPTION43 NOT DISCOUNTABLE4
Page 141 and 142:
Default System DescriptorsNO DESCRI
Page 143 and 144:
CASH DECLARATION REQUIREDCash decla
Page 145 and 146:
NOT DISCOUNTABLEThe preceding entry
Page 147 and 148:
Printer & KV RoutingThe printing sy
Page 149 and 150:
NOTE: All registers are updated wit
Page 151 and 152:
File ManagementUtilities available
Page 153 and 154:
AppendixReport Function Key Report
Page 155 and 156:
45 Checks for Current Employee X1 &
Page 157 and 158:
Glossary of TermsActivity CountThe
Page 159 and 160:
Currency ConversionUse one of the 5
Page 161 and 162:
Keyboard LevelEach keyboard level i
Page 163 and 164:
PromoThe PROMO operation allows ite
Page 165 and 166:
Index##/NO SALE 50, 95%%1 - %10 51,
Page 167 and 168:
TAX EXEMPT 52, 96Tax Options 107TAX
show all

SAM4s SPS-500 series programming manual.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?