SAM4s SPS-500 series programming manual.pdf

More documents

Recommendations

Info

1-2 Servicing PrecautionsWARNING: First read the-Safety Precautions-section of this manual. If some unforeseen circumstance creates aconflict between the servicing and safety precautions, always follow the safety precautions.WARNING: An electrolytic capacitor installed with the wrong polarity might explode.1. Servicing precautions are printed on the cabinet.Follow them.2. Always unplug the units AC power cord from theAC power source before attempting to:(a) Remove or reinstall any component or assembly(b) Disconnect an electrical plug or connector(c) Connect a test component in parallel with anelectrolytic capacitor3. Some components are raised above the printedcircuit board for safety. An insulation tube or tapeis sometimes used. The internal wiring issometimes clamped to prevent contact withthermally hot components. Reinstall all suchelements to their original position.4. After servicing, always check that the screws,components and wiring have been correctlyreinstalled. Make sure that the portion around theserviced part has not been damaged.5. Check the insulation between the blades of the ACplug and accessible conductive parts (examples: metal panels and input terminals).6. Insulation Checking Procedure:Disconnect the power cord from the AC source andturn the power switch ON. Connect an insulationresistance meter (500V) to the blades of AC plug.The insulation resistance between each blade of theAC plug and accessible conductive parts (seeabove) should be greater than 1 megohm.7. Never defeat any of the B+ voltage interlocks.Do not apply AC power to the unit (or any of itsassemblies) unless all solid-state heat sinks arecorrectly installed.8. Always connect an instrument’s ground lead to theinstrument chassis ground before connecting thepositive lead ; always remove the instrument’sground lead last.1-3 Precautions for Electrostatically Sensitive Devices (ESDs)1. Some semiconductor (solid state) devices are easilydamaged by static electricity. Such components arecalled Electrostatically Sensitive Devices (ESDs);examples include integrated circuits and some fieldeffecttransistors. The following techniques willreduce the occurrence of component damage causedby static electricity.2. Immediately before handling any semiconductorcomponents or assemblies, drain the electrostaticcharge from your body by touching a known earthground. Alternatively, wear a discharging wriststrapdevice. (Be sure to remove it prior to applyingpower - this is an electric shock precaution.)3. After removing an ESD-equipped assembly, placeit on a conductive surface such as aluminum foil toprevent accumulation of electrostatic charge.4. Do not use freon-propelled chemicals. These cangenerate electrical charges that damage ESDs.5. Use only a grounded-tip soldering iron whensoldering or unsoldering ESDs.6. Use only an anti-static solder removal device.Many solder removal devices are not rated as antistatic;these can accumulate sufficient electricalcharge to damage ESDs.7. Do not remove a replacement ESD from itsprotective package until you are ready to install it.Most replacement ESDs are packaged with leadsthat are electrically shorted together by conductivefoam, aluminum foil or other conductive materials.8. Immediately before removing the protectivematerial from the leads of a replacement ESD,touch the protective material to the chassis orcircuit assembly into which the device will beinstalled.9. Minimize body motions when handling unpackagedreplacement ESDs. Motions such as brushingclothes together, or lifting a foot from a carpetedfloor can generate enough static electricity todamage an ESD.
ContentsIntroduction 9SAM4s SPS-500 Series Overview.............................................................................................9Power Requirements....................................................................................................9Safe Operation...........................................................................................................10Important Battery Backup Note.................................................................................10SAM4s SPS-500 Configurations...............................................................................10Standard Hardware....................................................................................................10Standard Connectivity ...............................................................................................11Software ....................................................................................................................11Controls & Connections ..........................................................................................................12Front Panel Angle Adjustment ..................................................................................12Rear Customer Display..............................................................................................13SD Memory Card Slot...............................................................................................13Connection Panel.......................................................................................................14Control Lock............................................................................................................................15Default Screen Layout .............................................................................................................16Screen Saver..............................................................................................................16X Mode Main Menu..................................................................................................17Z Mode Main Menu ..................................................................................................17P Mode Main Menu...................................................................................................18S Mode Main Menu...................................................................................................18Keylinks...................................................................................................................................19Custom Screen Layouts ...........................................................................................................20Initialize...................................................................................................................................21Memory All Clear....................................................................................................................21Software Installation & SD Utilities 23Overview .................................................................................................................................23Important: Updating Existing Installations...............................................................23Update Methods ........................................................................................................23Required Support Resources .....................................................................................24SPS-500 Program Components .................................................................................24How to Verify Software Versions.............................................................................24How to Access System Menu....................................................................................25Application Upgrade/Backup from SD/USB...........................................................................28Capturing SPS-500 Screens.....................................................................................................30Equipment Required..................................................................................................30Screen Capture Procedure .........................................................................................30Image Downloads....................................................................................................................31Tips for Getting Images Ready..................................................................................31Image Download Using SD Memory Card ...............................................................32Screen Saver Logo ....................................................................................................33Downloading Logo Images for the Internal Printer.................................................................33S Mode Programming 35S- Mode Programming Screen.................................................................................................35Self Tests .................................................................................................................................36SPS-500 Program Manual v1.13 Contents 5
Page 6 and 7: Memory Clearing....................
Page 8 and 9: 8 Contents SPS-500 Program Manual
Page 10 and 11: Safe OperationDo not locate your SA
Page 12 and 13: Controls & ConnectionsThe Power LED
Page 14 and 15: Connection PanelStandard ports incl
Page 16 and 17: Default Screen LayoutMain ScreenUp
Page 18 and 19: P Mode Main MenuNote: P Mode Menu b
Page 20 and 21: Custom Screen LayoutsAfter your aut
Page 22 and 23: 6. The display will monitor the mem
Page 24 and 25: Required Support ResourcesA PC with
Page 26 and 27: Diagnostics/Functions Available for
Page 28 and 29: Application Upgrade/Backup from SD/
Page 30 and 31: Capturing SPS-500 ScreensEquipment
Page 32 and 33: Image Download Using SD Memory Card
Page 35 and 36: S Mode ProgrammingS- Mode Programmi
Page 37 and 38: KEYBOARD TESTThis will test the key
Page 39 and 40: Memory AllocationCAUTION: The proce
Page 41 and 42: (16) PROJECTIONSThe Product Project
Page 43 and 44: Key Relocation Screen—Screen Tab1
Page 45 and 46: Key Relocation Screen—Design TabS
Page 47 and 48: 145 MODIFIER 10146 Reserved147 #/NO
Page 49 and 50: EMPLOYEE (1-10) 041-050The EMPLOYEE
Page 51 and 52: PAID OUT 1-5 151-155Touch a PAID OU
Page 53 and 54:
TAX SHIFT 1-6 225-230Use to shift t
Page 55 and 56:
System OptionsThis section is used
Page 57 and 58:
Select SERIAL or ETHERNET.PC CONNEC
Page 59 and 60:
Printer Driver SelectionsThis progr
Page 61 and 62:
CUTTING AFTER PRINTINGWhen a printe
Page 63 and 64:
Password NotesThe correct password
Page 65 and 66:
4. The SRAM BACKUP (SD) dialog box
Page 67 and 68:
FTP TransmissionChoose FTP Transmis
Page 69 and 70:
P Mode ProgrammingP Mode Programmin
Page 71 and 72:
PLU Add & Change1. From the P mode
Page 73 and 74:
PRODUCT MIX #1This works in-conjunc
Page 75 and 76:
PLU Status GroupPLU Status Groups a
Page 77 and 78:
(16) STOCK PLU?Choose Yes if you wi
Page 79 and 80:
(42) ELIGIBLE FOR CANADIAN DONUT LA
Page 81 and 82:
NON-PLU Code Field DefinitionsLENGT
Page 83 and 84:
Age Verification by Card Swipe(Cali
Page 85 and 86:
3. Once PLUs are added they will be
Page 87 and 88:
10. Touch ADDType the descriptor: C
Page 89 and 90:
Format of Automatically Created Scr
Page 91 and 92:
PLU GroupGroups are designated to a
Page 93 and 94:
Function Key Program SummaryDescrip
Page 95 and 96:
DescriptorManagerRequiredHALO(RATE)
Page 97 and 98:
DescriptorManagerRequiredHALO(RATE)
Page 99 and 100:
Modifier Key Program NotesAFFECT DI
Page 101 and 102:
System OptionsOptions are sorted by
Page 103 and 104:
(10) ROUNDING SYSTEMUse these optio
Page 105 and 106:
(42) BASE CURRENCYSet for local cur
Page 107 and 108:
(62) USE STOCK LINK PLU ON PLU PGMC
Page 109 and 110:
(9) OPEN DRAWER DURING CASH DECLARA
Page 111 and 112:
(4) SELECT HELD ITEMS ON RECALLItem
Page 113 and 114:
(5) COMBINE LIKE ITEMS ON KP OR KVS
Page 115 and 116:
(8) DISPLAY RUNNING SUBTL ON POLEAl
Page 117 and 118:
(33) NOT PRINT AN ALPHA TEXT MESSAG
Page 119 and 120:
Report Options(1) ONLY TTL ON PRODU
Page 121 and 122:
If Yes, the percentage entered here
Page 123 and 124:
EmployeeThe employee file contains
Page 125 and 126:
EDIT JOB CODESNote: An employee wit
Page 127 and 128:
(30) ALLOW PLU QUICK REGISTER?(31)
Page 129 and 130:
ReportsUse this program to create a
Page 131 and 132:
TimeTime period definitions and tim
Page 133 and 134:
Product & IngredientNOTE: Be carefu
Page 135 and 136:
Product Mix Group Time PeriodsMemor
Page 137 and 138:
# OF NON-REPEAT BREAKSEnter the num
Page 139 and 140:
NO. DESCRIPTION43 NOT DISCOUNTABLE4
Page 141 and 142:
Default System DescriptorsNO DESCRI
Page 143 and 144:
CASH DECLARATION REQUIREDCash decla
Page 145 and 146:
NOT DISCOUNTABLEThe preceding entry
Page 147 and 148:
Printer & KV RoutingThe printing sy
Page 149 and 150:
NOTE: All registers are updated wit
Page 151 and 152:
File ManagementUtilities available
Page 153 and 154:
AppendixReport Function Key Report
Page 155 and 156:
45 Checks for Current Employee X1 &
Page 157 and 158:
Glossary of TermsActivity CountThe
Page 159 and 160:
Currency ConversionUse one of the 5
Page 161 and 162:
Keyboard LevelEach keyboard level i
Page 163 and 164:
PromoThe PROMO operation allows ite
Page 165 and 166:
Index##/NO SALE 50, 95%%1 - %10 51,
Page 167 and 168:
TAX EXEMPT 52, 96Tax Options 107TAX
show all

SAM4s SPS-500 series programming manual.pdf

Create successful ePaper yourself

Delete template?

Save as template?