Catalyst 3560-E Switch Getting Started Guide - Cisco
Catalyst 3560-E Switch Getting Started Guide - Cisco Catalyst 3560-E Switch Getting Started Guide - Cisco
1 About this GuideThis guide provides instructions on how to use Express Setup to initially configure your Catalystswitch. Also covered are switch management options, basic rack-mounting procedures, port andmodule connection procedures, and troubleshooting help.For additional installation and configuration information for Catalyst 3560-E switches, see theCatalyst 3560-E documentation on Cisco.com. For system requirements, important notes, limitations,open and resolved bugs, and last-minute documentation updates, see the release notes, also onCisco.com.When using the online publications, refer to the documents that match the Cisco IOS software versionrunning on the switch. The software version is on the Cisco IOS label on the switch rear panel.For translations of the warnings that appear in this publication, see the Regulatory Compliance andSafety Information for the Catalyst 3750-E and Catalyst 3560-E Switch that accompanies this guide.2 Taking Out What You NeedFollow these steps:1. Unpack and remove the switch and the accessory kit from the shipping box.2. Return the packing material to the shipping container, and save it for future use.3. Verify that you have received the items shown on page 3. If any item is missing or damaged,contact your Cisco representative or reseller for instructions.Some switch models might include additional items that are not shown on page 3.4. For switches with the optional 1150-W power supply module (model C3K-PWR-1150WAC),install the power supply in the switch as described in the installation notes after you rack-mountthe switch.2
SYSTRPSMASTRSTATDUPLXSP EDSTACKPoEMODE1X2X1X12X49X2-1X2-2Catalyst 3560-E SERIES PoE-48515052Shipping Box Contents12ProductDocumentationand Compliance1 2 3 4 5 6 7 8 9 10 1 1213 14 15 16 17 18 19 20 21 2 23 2413X 23X25 26 27 28 29 30 31 32 3 34 35 3625X 35X14X 24X37 38 3 9 40 41 42 43 4 45 46 47 4837X a26X 36X38X 48X3 4 56 78910 11 122073821 Catalyst switch 17 Four rubber mounting feet2 Documentation 8 Power cord retainer3 AC power cord 9 Twelve number-8 Phillips flat-head screws4 Console cable (optional) 10 Four number-12 Phillips machine screws5 Two 19-inch mounting brackets 11 One black Phillips machine screw6 Cable guide 12 Ground lug screw and ring terminal1. Catalyst 3560E-48 Power over Ethernet (PoE) switch shown for example. Your switch model might look different.3
- Page 1: GETTING STARTED GUIDECatalyst 3560-
- Page 7 and 8: Step 15Step 16(Optional) You can en
- Page 9 and 10: Refreshing the PC IP AddressAfter y
- Page 11 and 12: Other Management OptionsYou can use
- Page 13 and 14: WarningTo prevent bodily injury whe
- Page 15 and 16: 10-5 A50-60 HZAC OK PS OKAttaching
- Page 17 and 18: 6 Connecting to the Switch PortsThi
- Page 19 and 20: Install SFP Modules and Connect to
- Page 21 and 22: Resetting the SwitchThis section de
- Page 23 and 24: 9 Cisco Warranty TermsCatalyst 3560
1 About this <strong>Guide</strong>This guide provides instructions on how to use Express Setup to initially configure your <strong>Catalyst</strong>switch. Also covered are switch management options, basic rack-mounting procedures, port andmodule connection procedures, and troubleshooting help.For additional installation and configuration information for <strong>Catalyst</strong> <strong>3560</strong>-E switches, see the<strong>Catalyst</strong> <strong>3560</strong>-E documentation on <strong>Cisco</strong>.com. For system requirements, important notes, limitations,open and resolved bugs, and last-minute documentation updates, see the release notes, also on<strong>Cisco</strong>.com.When using the online publications, refer to the documents that match the <strong>Cisco</strong> IOS software versionrunning on the switch. The software version is on the <strong>Cisco</strong> IOS label on the switch rear panel.For translations of the warnings that appear in this publication, see the Regulatory Compliance andSafety Information for the <strong>Catalyst</strong> 3750-E and <strong>Catalyst</strong> <strong>3560</strong>-E <strong>Switch</strong> that accompanies this guide.2 Taking Out What You NeedFollow these steps:1. Unpack and remove the switch and the accessory kit from the shipping box.2. Return the packing material to the shipping container, and save it for future use.3. Verify that you have received the items shown on page 3. If any item is missing or damaged,contact your <strong>Cisco</strong> representative or reseller for instructions.Some switch models might include additional items that are not shown on page 3.4. For switches with the optional 1150-W power supply module (model C3K-PWR-1150WAC),install the power supply in the switch as described in the installation notes after you rack-mountthe switch.2
Change language