Catalyst 3560-E Switch Getting Started Guide - Cisco
Catalyst 3560-E Switch Getting Started Guide - Cisco Catalyst 3560-E Switch Getting Started Guide - Cisco
STATDUPLXSPEEDPoEMODE1X2XSTATDUPLXSPEEDPoEMODE1X2X1X12X1X12X49X2-1X2-251505249X2-1X2-2Catalyst 3560-E SERIES PoE-4851AC OK PS OK50521 0-240V ~1.0-5A50-60 HZRack-Mount the SwitchUse the four number-12 Phillips machine screws to attach the brackets to the rack. Use the blackPhillips machine screw to attach the cable guide to the left or right bracket.2 3SYSTRPS1 2 3 4 5 6 7 8 9 10 1 1213 14 15 16 17 18 19 20 21 2 23 2413X 23X25 26 27 28 29 30 31 32 3 34 35 3625X 35X14X 24X37 38 3 9 40 41 42 43 4 45 46 47 4837X 47X26X 36X138X 48XCatalyst 3560-E SERIES PoE-48541 2 3 4 5 6 7 8 9 10 1 12SYSTRPS13 14 15 16 17 18 19 20 21 2 23 2413X 23X25 26 27 28 29 30 31 32 3 34 35 3625X 35X14X 24X37 38 3 9 40 41 42 43 4 45 46 47 4837X 47X26X 36X38X 48X642029381 Black Phillips machine screw 4 Number-12 Phillips machine screws2 Cable guide 5 Mid-mounting position3 Front-mounting position 6 Rear-mounting position16
6 Connecting to the Switch PortsThis section describes how to connect to the fixed switch ports, to the 10-Gigabit Ethernet moduleslots, and to the SFP module slots. Some switch models might not include 10/100/1000 Ethernet ports,10/100/1000 PoE ports, or SFP slots.Connect to 10/100/1000 PortsThe 10/100/1000 Ethernet ports use standard RJ-45 connectors with Ethernet pinouts. The maximumcable length is 328 feet (100 meters). The 100BASE-TX and 1000BASE-T traffic requires Category 5,Category 5e, or Category 6 UTP cable. The 10BASE-T traffic can use Category 3 or Category 4 cable.The autonegotiation feature is enabled by default on the switch. At this setting, the switch portsconfigure themselves to operate at the speed of attached devices. If the attached device does notsupport autonegotiation, you can explicitly set the switch port speed and the duplex parameters. Tomaximize performance, either let the ports autonegotiate both speed and duplex, or set the port speedand duplex parameters on both ends of the connection.For simplified cabling, the automatic medium-dependent interface crossover (auto-MDIX) feature isenabled by default on the switch. With auto-MDIX enabled, the switch detects the required cable typefor copper Ethernet connections and configures the interface accordingly. Therefore, you can use eithera crossover or a straight-through cable for connections to a switch 10/100/1000 Ethernet port,regardless of the type of device on the other end of the connection.See the switch software configuration guide or the switch command reference on Cisco.com for moreinformation about enabling or disabling autonegotiation and auto-MDIX.Connect to 10/100/1000 PoE PortsThe 10/100/1000 PoE ports have the same default settings and cabling requirements that are describedin the previous section.The PoE ports provide PoE support for devices compliant with IEEE 802.3af and also provide Ciscopre-standard PoE support for Cisco IP Phones and Cisco Aironet Access Points.Each port can deliver up to 15.4 W of PoE. With the 1150-W power supply module, theCatalyst 3560E-48PS switch can deliver 15.4 W on all 48 ports. With the 750-W power supplymodule, the switches can deliver 15.4 W of PoE on any 24 of the 48 ports, or any combination of theports can deliver an average of 7.7 W of PoE at the same time, up to a maximum switch power outputof 370 W. On a per-port basis, you can control whether or not a PoE port automatically providespower when an IP phone or an access point is connected.See the hardware installation guide on Cisco.com for more information about the switch power supplyoptions.17
- Page 1 and 2: GETTING STARTED GUIDECatalyst 3560-
- Page 3 and 4: SYSTRPSMASTRSTATDUPLXSP EDSTACKPoEM
- Page 7 and 8: Step 15Step 16(Optional) You can en
- Page 9 and 10: Refreshing the PC IP AddressAfter y
- Page 11 and 12: Other Management OptionsYou can use
- Page 13 and 14: WarningTo prevent bodily injury whe
- Page 15: 10-5 A50-60 HZAC OK PS OKAttaching
- Page 19 and 20: Install SFP Modules and Connect to
- Page 21 and 22: Resetting the SwitchThis section de
- Page 23 and 24: 9 Cisco Warranty TermsCatalyst 3560
STATDUPLXSPEEDPoEMODE1X2XSTATDUPLXSPEEDPoEMODE1X2X1X12X1X12X49X2-1X2-251505249X2-1X2-2<strong>Catalyst</strong> <strong>3560</strong>-E SERIES PoE-4851AC OK PS OK50521 0-240V ~1.0-5A50-60 HZRack-Mount the <strong>Switch</strong>Use the four number-12 Phillips machine screws to attach the brackets to the rack. Use the blackPhillips machine screw to attach the cable guide to the left or right bracket.2 3SYSTRPS1 2 3 4 5 6 7 8 9 10 1 1213 14 15 16 17 18 19 20 21 2 23 2413X 23X25 26 27 28 29 30 31 32 3 34 35 3625X 35X14X 24X37 38 3 9 40 41 42 43 4 45 46 47 4837X 47X26X 36X138X 48X<strong>Catalyst</strong> <strong>3560</strong>-E SERIES PoE-48541 2 3 4 5 6 7 8 9 10 1 12SYSTRPS13 14 15 16 17 18 19 20 21 2 23 2413X 23X25 26 27 28 29 30 31 32 3 34 35 3625X 35X14X 24X37 38 3 9 40 41 42 43 4 45 46 47 4837X 47X26X 36X38X 48X642029381 Black Phillips machine screw 4 Number-12 Phillips machine screws2 Cable guide 5 Mid-mounting position3 Front-mounting position 6 Rear-mounting position16
Change language