Cooling/Casting - Spraying Systems Co.

LegendWorld HeadquartersWheaton, IL USA●Sales OfficesManufacturing LocationsHudson, NH USAWheaton, IL USABelgiumBrazilChinaGermanyIndiaItalyJapanKoreaCover and inside back cover photos courtesy of MACSTEEL ® , Republic Engineered Products, Inc. and United States Steel Corporation.

Table of ContentsProduct Primary Application Page No.CasterJet ® Nozzles .............................Cooling/Continuous Casting ................................ 226010 Air Atomizing ................................................................................................................ 5FullJet ® Nozzles ..................................Cooling/Casting ..................................................... 6HHX FullJet .............................................................................................................................. 7HHCC FullJet ............................................................................................................................ 8Standard/Square/Wide Angle ............................................................................................ 10UniJet ® ................................................................................................................................... 11Vaneless ................................................................................................................................. 11Oval ......................................................................................................................................... 11Large capacity DistriboJet ® ............................................................................................... 12P45075 ..................................................................................................................................... 12VeeJet ® Nozzles ..................................Lubrication/Cooling/Strip Wash-Off ................ 22Quick VeeJet, UniJet ............................................................................................................ 23Dovetail VeeJet ..................................................................................................................... 3418897 Dovetail ........................................................................................................................ 36XT VeeJet ............................................................................................................................... 39Rectangular VeeJet .............................................................................................................. 40DescaleJet ® Nozzles .........................Descaling/Hot Strip Mill .................................... 41AA214 ...................................................................................................................................... 4726180/26190/218 ..................................................................................................................... 50Optimizing Spray Applications in Your Mill ................................................................... 43Flowline of Steelmaking ..................................................................................................... 44Areas of Your Mill that May Benefit from Spray System Automation ....................... 46FlatJet ® Nozzles ..................................Strip Wash-Off/Hot Strip Mill ........................... 54FloodJet ® Nozzles ................................................................................................................ 54WashJet ® Nozzles ..............................Strip Wash-Off/Hot Strip Mill ........................... 58Laminar Flow ........................................Run-Off Table/Hot Strip Mill ............................. 60Solid stream version ............................................................................................................. 60Slit type ................................................................................................................................... 60Spray Headers ......................................Lubrication/Strip Wash-Off/Cold Strip Mill ... 61Automatic Brush Header ..................................................................................................... 61Manual Brush Header .......................................................................................................... 61WindJet ® Air Control Nozzles ..........Strip Blow-Off/Cold Strip Mill .......................... 63WindJet Nozzles ................................................................................................................... 63Air Knife .................................................................................................................................. 65Air Atomizing & AutomaticAutoJet ® Spray Controllers ..............Spangling/Cold Strip Mill .................................. 66VAU/VMAU ............................................................................................................................. 67J-Series Air Atomizing ......................................................................................................... 68WhirlJet ® Spray Nozzles ...................Dust Control/Gas Cooling .................................. 78SpiralJet ® Spray Nozzles ..................Dust Control/Gas Cooling .................................. 79FloMax ® Nozzles and AutoJet ® .....Emission Control/Gas Conditioning System ...................Scrubber/Gas Conditioning ............................... 86

Cooling/Continuous CastingCasterJet Nozzles – Unmatched forSecondary Cooling in the CasterThe key to the superior performance of CasterJet nozzles is a unique process formixing air and water. This results in:• Improved surface quality through uniform spray distribution and reduced waterbuildup under rollers• Reduced water costs -- More effective heat transfer means less water is requiredfor cooling and large free-passage openings mean lower quality water can beused• Increased operating versatility -- Variable water flows can accommodate a widerange of steel types and alloys• Reduced maintenance costs -- Fewer nozzles needed per installation so fewernozzles need to be maintained; self-aligning spray tips and new detachableexpansion tubes speed replacement; and less puddling between support rollersreduces clean up time and extends roller life• A potential 25% reduction in air consumption on a continuous caster while maintainingthe same performance (compared with older designs)2

Cooling/Continuous CastingCasterJet Nozzles – How They WorkCasterJet nozzles use an atomization process based on a unique impingementprinciple involving three factors:• A high velocity stream of water forced into an expansion chamber• A target bolt, against which the water stream is shattered• An air stream rushing past the target bolt to further break up the water streamA recent design enhancement in the expansion chamber results in even more efficientmixing. CasterJet nozzles now provide more performance with a 25% reductionin air consumption. This means new caster lines may require fewer or smallercompressors. On existing caster lines, some compressors can be turned off. Thistranslates into lower energy costs and longer compressor life.The nozzle’s target bolt also provides an even greater break-up efficiency thanbefore and are now press-fit into the CasterJet nozzle body.CasterJet nozzles offer a turndown ratio of 25:1. Flow can be reduced using waterpressures as low as 5 psi (.3 bar) without a loss in performance. Wider operatingranges and consistent drop size distribution across the spray pattern allow greaterflexibility in line speeds and the ability to run additional grades of steel.Easy to MaintainCasterJet extension tubes feature broached connections for detachability with aferrule for connecting and a locating pin for safety. Because tubes are detachable,a wide range of lengths can be used. And, when breakouts occur, maintenance iseasier – simply replace the tube and tip instead of the entire nozzle assembly.The CasterJet spray tip, with a new snap ring assembly, is even easier to removefor fast and simple changes. The spray tips are self-aligning and the entire nozzleassembly features smooth, clean passages. Nozzle wear is low due to generallylow operating pressures.Specifications:• Operating range: 2 to 12 gpm (7.6 to 45.4 l/min) at 45 psi air and 100 psi liquid(3 bar air and 7 bar liquid)• Spray angles: 60° to 135°• Materials: Stainless steel wear components including spray tip orifices and targetbolts. Brass bodies and extensions• Inlet connection: 3/8” to 1/2”IMPROVED EXPANSION CHAMBERREDUCES AIR CONSUMPTIONRE-DESIGNED TARGET BOLTIMPROVES BREAK-UP EFFICIENCY3

Cooling/Continuous CastingWater Flow Rate vs. Air FlowRate at Constant Air PressurePerformanceNozzle Set-up50070-Water Flow7 bar (l/min)Air Flow3 bar (l/min)_-NCJ-2-_-SS 7.6 147_-NCJ-2.5-_-SS 9.5 162_-NCJ-3-_-SS 11.4 174_-NCJ-3.5-_-SS 13.2 242_-NCJ-3.7-_-SS 15.1 255_-NCJ-4-_-SS 18.9 284_-NCJ-5-_-SS 24.6 289_-NCJ-6.5-_-SS 30.0 441Nozzle Set-up50085-Water Flow7 bar (l/min)Air Flow3 bar (l/min)_-NCJ-8-_-SS 34.0 517_-NCJ-9-_-SS 40.0 718_-NCJ-10-_-SS 45.0 634_-NCJ-12-_-SS 57.0 634Dimensions 50070/50085Ordering Info50070/50085 Nozzle Set-Up3/8NCJ – 3 – 120 – SS1/2NCJ – 8 – 120 – SS50070/50085 Assembly Style50070 – BRSS + 50080 – 35050085 – BRSS + 50094 – 400Inlet Capacity Spray MaterialConn. Size AngleAssembly StyleLength4

26010 Air AtomizingCooling/Continuous Casting26010 Air Atomizing Nozzles Provide SofterContinuous Cast CoolingIf you’re only running a few grades of steel, our 26010 Air Atomizing nozzle may bea suitable alternative to our CasterJet® nozzles. An air mist style nozzle, the 26010provides softer, impingement-type cooling – performance typically achieved byhydraulic nozzles. Performance can be visually identified by rings on air cap.Specifications:• All brass construction• Inlet connection: 1/4”PerformanceNozzle AssemblyNo.Number ofI.D. RingsPressure (bar)Spray PerformanceCapacityAir Fluid Air (NI/min) Water (l/min)Spray Angle (degree)26010-0-1/4J NONE 2.8 2.6 85 1.9 9026010-1-1/4J 1 2.8 2.3 275 3.8 9026010-2-1/4J 2 2.8 2.4 297 5.7 9026010-3-1/4J 3 2.8 4.1 176 10.6 9026010-4-1/4J 4 2.8 2.4 297 5.7 12026010-5-1/4J 5 2.8 4.1 156 10.6 120Dimensions26010Ordering Info26010 Air Atomizing Nozzle26010 – 1 – 1/4JSpray ID NozzleSet-Up Rings Body5

Cooling/CastingFullJet Nozzles – Uniform DistributionEnhances Steel Quality in Every Areaof Your MillHot spots, cracks and defects – all costly but common problems that can lead towaste. One way to avoid quality problems like these is to use our FullJet spraynozzles. These nozzles feature a unique vane design with large flow passages toprovide a uniform spray over a wide range of flow rates and pressures. This evenand consistent spray coverage results in center-to-edge cooling and defect-freesteel.Our line of FullJet nozzles is extensive. Choose from a wide assortment of styles,sizes, capacities, connections, spray angles, impact areas, materials and more.Common uses for FullJet nozzles include:• Uniform cooling in continuous cast slabs, continuous cast billets, finishing• Fast and uniform quenching• Thorough liquor flushing6

HHXCooling/CastingHHX FullJet Nozzles – Provide UniformDistribution, Reliable Operation and SimplifiedMaintenance in Billet CastersQuality sprays contribute to better steel and increase the efficiency of your caster,and our HHX FullJet nozzles do exactly that – provide uniform cooling to ensurequality problems like diagonal cracks are avoided.Key benefits and features include:• A wide range of nozzle sizes allows you to select different spray densities to customizethe spray zone cooling• The HHX nozzle body features a hex body and allows the use of standard socketsfor easy installation and removal• A staked-in vane design ensures the vane is secure and will not fall out duringcaster operationSpecifications:• Capacities range from .50 to 2.2 gpm (1.9 to 8.4 l/min) at 10 psi (.7 bar)• All brass construction with a staked vane• Inlet connections: 1/4” and 3/8”Ordering InfoDimensionsHHX FullJet Spray Nozzle1/4 HHX - 5Inlet Nozzle CapacityConn. Type SizePerformance* At stated pressure in bar.Nozzle InletConn. NPT orBSPT (in.)1/43/8Nozzle No.OrificeDia.Nom.Max. FreePassageDia.Capacity (Liters per minute)*Spray AngleDegree*mm mm .5 .7 1.5 2 3 4 5 6 7 10 .5 1.5 61/4HHX-5 1.95 1.3 1.6 1.9 2.7 3.1 3.7 4.2 4.7 5.1 5.5 6.5 60 65 611/4HHX-6.5 2.4 1.6 2.1 2.5 3.5 4.0 4.8 5.5 6.1 6.7 7.1 8.4 45 50 461/4HHX-8 2.8 1.2 2.6 3.0 4.3 4.9 6.0 6.8 7.5 8.2 8.8 10.4 68 80 761/4HHX-10 2.8 1.6 3.3 3.8 5.4 6.2 7.4 8.5 9.4 10.2 11.0 13.0 58 67 611/4HHX-12 3.2 1.6 3.9 4.6 6.5 7.4 8.9 10.2 11.3 12.3 13.2 15.5 71 81 721/4HHX-14.5 3.6 1.6 4.7 5.5 7.8 9.0 10.8 12.3 13.7 14.8 15.9 18.8 78 89 753/8HHX-15 3.6 2.4 4.9 5.7 8.1 9.3 11.2 12.7 14.1 15.4 16.5 19.4 64 67 613/8HHX-18 4.0 2.4 5.9 6.9 9.7 11.1 13.4 15.3 16.9 18.4 19.8 23 77 86 733/8HHX-20 4.4 2.8 6.5 7.6 10.8 12.4 14.9 17.0 18.8 20 22 26 76 80 733/8HHX-22 4.8 2.8 7.2 8.4 11.9 13.6 16.4 18.7 21 23 24 28 87 90 827

Cooling/CastingHHCCHHCC FullJet Nozzles – The Most Stable,Uniform Full Cone Spray AvailableTypical full cone nozzles deliver water in a full cone spray. But liquid distribution canvary. Everything gets wet, but some spots get wetter than others. And this can leadto costly defects resulting from uneven cooling. The patent-pending design of ourHHCC FullJet delivers a spray that is more uniform across the cone. This results inconsistent, controlled cooling that meets even the most stringent demands.Here’s how the HHCC FullJet helps control temperature of the strand, a critical componentof maximizing uptime with high-speed continuous casting machines:• New staked vane design yields a more uniform and stable spray over the operatingrange of 10 to 80 psi (.7 to 5.5 bar). Changes in pressure do not impact thenozzle’s spray angle• The vanes are precisely matched with each nozzle size to ensure exact performance• Obtain the mass water flux you need for every casting application through a wideselection of nozzle sizes. There’s a 25% nominal flow rate increase at every sizeincrement, simplifying layout of flow rates for each segmentSpecifications:• Capacities range from .65 to 3.2 gpm (2.5 to 12.1 l/min) at 10 psi (.7 bar)• Brass construction with a staked vane• Inlet connections: 1/4”, 3/8” and 1/2”Dimensions8

HHCCCooling/CastingPerformance* At stated pressure in bar.NozzleInlet Conn.NPT orBSPT (in.)Nozzle No.OrificeDia.Nom.Max.FreePassageDia.Capacity (Liters per minute)*Spray AngleDegree*mm mm .7 1.5 2 3 3.5 4 5 5.5 6 7 1.5 3 61/4HHCC-6.5 2.1 1.7 2.5 3.4 4.2 4.9 5.3 5.7 6.1 6.4 6.8 7.2 68 68 681/41/4HHCC-8 2.2 1.8 3.0 4.2 4.9 5.7 6.4 6.8 7.6 7.9 8.3 8.7 68 68 681/4HHCC-10 2.5 1.9 3.8 5.3 6.4 7.2 8.3 9.1 9.5 10.2 6.6 11.4 74 74 741/4HHCC-12.5 2.7 2.2 4.7 6.4 7.9 9.1 10.2 11 11.7 12.5 13.2 14 74 74 743/8 3/8HHCC-15 3.3 2.6 5.7 7.9 9.5 11 12.1 13.2 14 15.1 15.9 16.7 74 74 741/2HHCC-20 2.8 2.9 7.6 10.6 12.9 14.4 16.3 17.4 18.9 20.1 21.2 22 74 74 741/2 1/2HHCC-25 3.0 3.0 9.5 13.2 15.9 18.2 20.1 22 23.5 25 26.5 27.6 74 74 741/2HHCC-32 4.3 2.8 12.1 17 20.4 23.1 25.7 28 29.9 31.8 33.7 35.6 74 74 74Ordering InfoHHCC FullJet Spray Nozzle1/4 HHCC – 6.5Inlet Nozzle CapacityConn. Type Size9

Cooling/CastingFullJet Nozzles Are Ideal for Cooling in Semi-Finishing, Quenching, Liquor Flushing and MoreOur FullJet nozzles produce a solid cone-shaped spray pattern consisting of mediumto large sized drops with a round impact area. The spray pattern is uniform,providing even and thorough center-to-edge coverage to enhance steel quality.A unique vane design with large flow passages is responsible for the uniformcoverage.There’s a FullJet nozzle for almost every cooling application in your mill. The nozzlesare available in a wide variety of configurations, capacities, connections, materials,spray angles and sizes. Many models are available with a choice of impactareas of wide angle, square and oval.GGGHHRemovable cap and vane1/8” to 1/2” NPT or BSPT (F)Removable cap and vane1/8” to 1/2” NPT or BSPT (M)• G and GG FullJet nozzles feature removable caps andvanes for easy cleaning and inspection. The nozzle bodycan remain in the header or manifold.• Available in standard spray, wide angle spray and squarespray.One-piece body1/8” to 1” NPT or BSPT (M)• HH FullJet nozzles have aone-piece body and nonremovablevanes.• Available in standard spray,wide angle spray, squarespray and wide anglesquare spray.GAGGAGDGGDAngle typeRemovable cap and vane1/8” to 1/2” NPT or BSPT (F)Angle typeRemovable cap and vane1/8” to 1/2” NPT or BSPT (M)• GA and GGA FullJet nozzles have a right angle design forinstallation on a pipe extension over the center of a sprayzone or in a side-tapped header or manifold. The spray isprojected from nozzle at an axis 90° from the axis of thenozzle inlet.• Available in standard spray and wide angle spray.Wall mountedRemovable cap and vane1/8” to 1/2” NPT or BSPT (F)Wall mountedRemovable cap and vane1/8” to 1/2” NPT or BSPT (M)• GD and GGD FullJet nozzles feature a wall mount connectionfor installations where the piping for the nozzle mustbe installed on the exterior of the room, vessel or pipelineinto which the nozzle will spray.• Available in standard spray.10

Cooling/CastingHHGANVGGANVOne piece body/vane3/4” to 1” NPT or BSPT (F)Removable vane/cast body1-1/4” to 3” NPT or BSPT (F)• H FullJet nozzles have a one-piece body with vane or aremovable vane/cast body.• Available in standard spray, wide angle spray, square sprayand wide angle square spray.Vaneless/removable cap1/4” to 1/2” NPTor BSPT (F)Vaneless/removable cap1/4” to 1/2” NPTor BSPT (M)• Vaneless FullJet nozzles feature completely unrestrictedinternal flow passages with no vane. Spray is projectedfrom the nozzle in a full cone pattern at an axis 90° fromthe axis of the nozzle inlet and is best used for applicationsrequiring a coarser spray.UniJet BodiesUniJet TGSpray TipGVLGGVLT female body orTT male bodySpray tipOne-piece spray tipwith vane• TG UniJet spray tips arepart of our UniJet System.Tips can be removed andreplaced while the nozzlebody remains in position.Plus, a variety ofother UniJet componentsare available – strainers,valves, connectors andmore.• Available in standardspray, wide angle sprayand square spray.Removable cap and vane3/8” NPT or BSPTRemovable cap and vane3/8” NPT or BSPT (M)• Oval FullJet nozzles have a solid cone-shaped spray withan oval impact area that has a width approximately onehalfits length. These nozzles are well suited for intensivecooling applications that require a heavy spray tobe projected between rollers to the target surface. OvalFullJet nozzles feature removable caps and vanes for easyinspection and cleaning.Tip retainer11

Cooling/CastingDistriboJetRRRP45075 FullJet Nozzles2” to 8” NPT or BSPT (F)(80°/95° orifice shown)2” to 8” NPT or BSPT (M)(50°/65° orifice shown)1/4” to 3/8” BSPP (F)• DistriboJet FullJet large capacity nozzles feature aninternal vane that is cast as part of the nozzle. Extralargeflow passages and a large open orifice assure noncloggingoperation. Spray angles range from 50° to 95°.• The operating range is 1 to 60 psi (.07 to 4 bar) witha full cone spray pattern developing at 1 psi (.07 bar).The 50° to 65° nozzles have specially designed groovedorifices for accurate flow rates and spray angle control.The 80° to 95° nozzles have smooth orifices with largerdiameters for the same flow rates.• Ideal for use on risers in billet casting, the P45075FullJet nozzle features a low profile design. Like otherFullJet nozzles, the P45075 provides a full cone patternwith even distribution and uses a secure, staked-invane design. Plus, the hex body allows use of socketwrench for easy installation and removal.• BSPP (F) inlet eliminates exposed thread on headers.12

Cooling/CastingPerformance – Standard FullJet Nozzles*At the stated pressure in bar.NozzleInletConn.NPT orBSPT(in.)Standard TypeNozzle TypeWallMountedAngleCapacitySizeMax.OrificeFreeDia.PassageNom.Dia.(mm)(mm)Capacity (Liters per minute)*Spray AngleDegree*G H GG HH GD GGD GA GGA .5 .7 1.5 2 3 4 5 6 7 10 .5 1.5 6● ● ● ● ● 1 .79 .64 — .38 .54 .62 .74 .85 .94 1.0 1.1 1.3 — 58 53● ● 1.5 1.2 .64 .49 .57 .81 .93 1.1 1.3 1.4 1.5 1.7 1.9 52 65 59● ● ● ● ● ● ● 2 1.2 1.0 .65 .76 1.1 1.2 1.5 1.7 1.9 2.0 2.2 2.6 43 50 461/8 ● ● ● ● ● ● ● 3 1.5 1.0 .98 1.1 1.6 1.9 2.2 2.5 2.8 3.1 3.3 3.9 52 65 59● ● ● ● ● ● ● 3.5 1.6 1.3 1.1 1.3 1.9 2.2 2.6 3.0 3.3 3.6 3.9 4.5 43 50 46● ● 3.9 2.0 1.0 1.3 1.5 2.1 2.4 2.9 3.3 3.7 4.0 4.3 5.1 77 84 79● ● ● ● ● ● ● 5 2.0 1.3 1.6 1.9 2.7 3.1 3.7 4.2 4.7 5.1 5.5 6.5 52 65 59● ● ● ● ● ● ● 6.5 2.4 1.6 2.1 2.5 3.5 4.0 4.8 5.5 6.1 6.7 7.1 8.4 45 50 461/4 ● ● ● ● ● ● ● 10 3.2 1.6 3.3 3.8 5.4 6.2 7.4 8.5 9.4 10.2 11.0 13.0 58 67 61● ● 12.5 3.2 1.6 4.1 4.8 6.8 7.7 9.3 10.6 11.8 12.8 13.7 16.2 69 74 683/8● ● ● ● ● ● ● 9.5 2.6 2.4 3.1 3.6 5.1 5.9 7.1 8.1 8.9 9.7 10.4 12.3 45 50 46● ● ● ● ● ● ● 15 3.6 2.4 4.9 5.7 8.1 9.3 11.2 12.7 14.1 15.4 16.5 19.4 64 67 61● ● ● ● ● ● 16 3.5 3.2 5.2 6.1 8.7 9.9 11.9 13.6 15.1 16.4 17.6 21 48 50 46● ● ● ● ● ● ● 25 4.6 3.2 8.2 9.5 13.5 15.4 18.6 21 24 26 27 32 64 67 611/2 ● ● ● ● 32 5.2 3.6 10.4 12.2 17.3 19.8 24 27 30 33 35 41 72 75 68● ● ● ● ● 40 6.2 3.6 13.1 15.2 22 25 30 34 38 41 44 52 88 91 83● ● 50 6.7 4.0 16.3 19.1 27 31 37 42 47 51 55 65 91 94 86● ● 2.5 4.9 4.4 9.6 11.2 15.9 18.2 22 25 28 30 32 38 48 50 463/4 ● ● 4.0 6.4 4.4 15.4 18.0 26 29 35 40 44 48 52 61 67 70 63● ● 7.0 9.5 5.2 27 31 45 51 61 70 78 84 91 107 89 92 84● ● 7.0 8.3 5.6 27 31 45 51 61 70 78 84 91 107 67 68 621● ● 8.0 9.5 5.6 31 36 51 58 70 80 89 97 104 122 72 81 82● ● 10 11.9 5.6 38 45 64 73 88 100 111 121 130 153 78 90 94● ● 12 11.9 6.4 46 54 77 87 105 120 133 145 155 183 89 92 841-1/4 ● 12 10.7 6.4 46 54 77 87 105 120 133 145 155 183 66 70 601-1/2● 10 9.5 8.7 38 45 64 73 88 100 111 121 130 153 64 67 58● 16 12.7 8.7 62 72 102 117 138 157 178 193 206 242 73 76 66● 40 21.0 11.1 154 180 255 295 350 400 445 485 520 610 78 80 702 ● 50 23.8 14.3 192 225 320 365 440 500 560 610 650 770 83 85 75● 60 28.6 14.3 230 270 385 440 530 600 670 730 780 920 98 100 86● 60 24.6 14.3 230 270 385 440 530 600 670 730 780 920 76 78 682-1/2 ● 70 28.6 14.3 270 315 450 510 620 700 780 850 910 1070 79 82 72● 80 28.6 17.5 310 360 510 590 700 800 890 970 1040 1220 86 88 77● 90 30.2 17.5 350 405 580 660 790 900 1000 1090 1170 1380 86 89 773 ● 100 32.5 17.5 385 450 640 730 880 1000 1110 1210 1300 1530 92 95 83● 120 34.9 20.6 465 540 770 880 1060 1200 1340 1450 1560 1840 102 105 89● 160 42.9 19.1 620 720 1020 1170 1410 1610 1780 1930 2080 2450 87 90 704● 180 47.2 22.2 700 810 1150 1310 1580 1810 2000 2170 2340 2750 92 95 83● 200 50.8 25.4 770 900 1280 1460 1760 2010 2220 2420 2590 3060 97 100 87● 210 54.8 25.4 810 950 1340 1530 1850 2110 2330 2540 2720 3210 102 105 91Maximum Free Passage Diameter is the maximum diameter as listedof foreign matter that can pass through the nozzle without clogging.Ordering InfoFullJet Spray Nozzle1/4 G – SS 5Inlet Nozzle Material CapacityConn. Type Code Size13

Cooling/CastingPerformance – Wide Angle, Square and Extra Wide AngleFullJet Nozzles*At the stated pressure in bar.Nozzle InletConn. NPT orBSPT (in.)1/81/43/81/23/4122-1/2Max. FreeSpray AngleNozzle TypeCapacity (Liters per minute)*CapacitySize Dia.PassageDegree*G H GG HH GA GGA (mm) 0.3 0.5 1 2 3 4 5 6 0.5 1.5 6● ● 1.5W .64 — — .67 .90 1.1 1.3 1.4 1.5 — 120 86● ● ● 2.8W 1.0 — — 1.2 1.7 2.0 2.3 2.5 2.7 — 120 102● ● ● ● ● 4.3W 1.0 — — 1.9 2.6 3.1 3.5 3.9 4.2 — 120 102● ● ● 4.8SQ 1.3 1.2 1.6 2.2 3.0 3.6 4.1 4.5 4.9 48 63 57● ● 5.6W 1.0 — 1.8 2.5 3.4 4.0 4.6 5.1 5.5 — 120 102● ● ● 6SQ 1.3 1.5 2.0 2.7 3.7 4.5 5.1 5.6 6.1 60 66 60● ● ● ● ● 8W 1.3 — 2.6 3.6 4.8 5.8 6.6 7.2 7.8 — 120 103● ● 10W 1.3 2.6 3.3 4.5 6.0 7.2 8.2 9.1 9.8 112 120 103● ● ● 10SQ 1.6 2.6 3.3 4.5 6.2 7.4 8.5 9.4 10.2 62 67 61● ● 12W 1.3 3.1 3.9 5.3 7.3 8.7 9.8 10.9 11.8 114 120 103● ● ● 12SQ 1.6 3.1 3.9 5.4 7.4 8.9 10.2 11.3 12.3 70 75 68● ● ● ● ● 14W 1.6 3.7 4.6 6.2 8.5 10.2 11.5 12.7 13.7 114 120 103● 14WSQ 1.6 3.7 4.6 6.2 8.5 10.1 11.5 12.7 13.7 99 101 9314.5SQ 1.6 3.7 4.7 6.5 9.0 10.8 12.3 13.7 14.8 78 82 75● ● ● 18SQ 2.4 4.6 5.9 8.1 11.1 13.4 15.3 17.0 18.4 71 75 68● ● ● ● ● 20W 2.4 5.2 6.6 8.9 12.1 14.5 16.5 18.1 19.6 114 120 104● 20WSQ 2.4 5.2 6.6 8.9 12.1 14.5 16.5 18.1 19.6 104 110 94● ● ● 29SQ 3.2 7.5 9.5 13.0 17.9 22 25 27 30 71 75 68● ● ● 30W 2.8 7.9 9.9 13.4 18.1 22 25 27 29 114 120 108● ● ● ● ● 35W 3.2 9.2 11.5 15.6 21 25 29 32 34 114 120 108● 35WSQ 3.2 9.2 11.5 15.6 21 25 29 32 34 104 110 102● ● ● 40W 3.2 10.5 13.1 17.8 24 29 33 36 39 114 120 108● ● ● 45W 3.6 11.8 14.8 20 27 33 37 41 44 114 120 110● ● ● ● ● 50W 4.0 13.1 16.4 22 30 36 41 45 49 114 120 112● ● 6W 4.4 18.4 23 31 42 51 58 64 69 115 120 112● 50SQ 4.4 12.9 16.3 22 31 37 42 47 51 71 75 68● ● 71WSQ 4.4 18.4 23 31 42 51 58 64 69 105 110 102● ● 11W 5.6 34 42 57 78 93 106 116 126 107 120 117● ● 130WSQ 5.6 34 42 57 78 93 106 116 126 107 110 107● 47W 11.1 144 181 254 335 400 455 500 540 120 124 119● 290SQ 11.1 75 95 130 179 215 250 275 300 66 70 64● 560WSQ 11.1 144 181 245 335 400 455 500 540 110 114 109● 70W 14.3 215 270 365 495 600 680 750 810 120 125 119● 830WSQ 14.3 215 270 365 495 600 680 750 810 110 115 109Maximum Free Passage Diameter is the maximum diameter as listed offoreign matter that can pass through the nozzle without clogging.Ordering InfoFullJet Spray Nozzle1/4 G – SS 14WInlet Nozzle Material CapacityConn. Type Code Size14

Cooling/CastingPerformance – Standard, Square and Wide Angle SprayUniJet Nozzle with TG TipNozzle InletConn. NPT orBSPT (in.)1/81/4*At the stated pressure in bar.Max. FreeSpray AngleNozzle TypeCapacity (Liters per minute)*Capacity PassageDegree*Size Dia.TG TG-W TG-SQ (mm) 0.3 0.5 0.7 2 3 4 5 6 0.3 0.7 6● 2.8W 1.0 — — 1.1 1.7 2.0 2.3 2.5 2.7 — 120 102● 4.3W 1.0 — — 1.6 2.6 3.1 3.5 3.9 4.2 — 120 102● 5.6W 1.0 — 1.8 2.1 3.4 4.0 4.6 5.1 5.5 — 120 102● 8W 1.3 — 2.6 3.0 4.8 5.8 6.6 7.2 7.8 — 120 103● 0.3 .41 — — — .19 .22 .25 .28 .31 — 50 61● 0.4 .46 — — — .25 .30 .34 .38 .41 — 56 63● 0.5 .51 — — — .31 .37 .42 .47 .51 — 56 63● 0.6 .51 — — — .37 .45 .51 .57 .61 — 54 62● 0.7 .51 — — — .43 .52 .60 .66 .72 — 54 63● 1 .64 — — — .62 .74 .85 .94 1.0 — 58 53● 2 1.0 — — .76 1.2 1.5 1.7 1.9 2.0 — 50 46● 2.8W 1.0 — — 1.1 1.7 2.0 2.3 2.5 2.7 — 120 102● 3 1.0 — — 1.1 1.9 2.2 2.5 2.8 3.1 — 65 59● 3.5 1.3 — — 1.3 2.2 2.6 3.0 3.3 3.6 — 50 46● 4.3W 1.0 — — 1.6 2.6 3.1 3.5 3.9 4.2 — 120 102● 5 1.3 — — 1.9 3.1 3.7 4.2 4.7 5.1 — 65 59● 5.6W 1.0 — 1.8 2.1 3.4 4.0 4.6 5.1 5.5 — 120 102● 6SQ 1.3 1.5 2.0 2.7 3.7 4.3 4.9 5.8 6.3 60 66 60● 6.5 1.6 2.1 2.5 3.5 4.0 4.8 5.5 6.1 6.7 45 50 46● 8W 1.3 — 2.6 3.0 4.8 5.8 6.6 7.2 7.8 — 120 103● 8SQ 1.3 2.1 2.6 3.6 4.9 5.9 6.7 7.4 8.3 70 75 68● 10 1.6 3.3 3.8 5.4 6.2 7.4 8.5 9.4 10.2 58 67 61● 10W 1.3 2.6 3.3 3.8 6.0 7.2 8.2 9.1 9.8 112 120 103● 10SQ 1.6 2.6 3.3 4.5 6.3 7.5 8.5 9.5 10.2 62 66 60● 12W 1.3 3.1 3.9 4.6 7.3 8.7 9.8 10.9 11.8 114 120 103● 12SQ 1.6 3.1 3.9 5.4 7.4 8.9 10.2 11.3 12.3 70 75 68● 14W 1.6 3.7 4.6 5.3 8.5 10.1 11.5 12.7 13.7 114 120 1033/8 ● 18SQ 2.4 4.6 5.9 8.1 11.1 13.4 15.3 17.0 18.4 71 75 68Maximum Free Passage Diameter is the maximum diameter as listed offoreign matter that can pass through the nozzle without clogging.Ordering InfoUniJet Spray NozzleNozzle BodySpray Tip1/4 T – SS + TG – SS 10Inlet Nozzle Material Tip Material CapacityConn. Type Code Type Code Size15

Cooling/CastingPerformance – Oval Spray FullJet Nozzles*At the stated pressure in bar.Nozzle InletConn. NPT orBSPT (in.)CapacitySizeMax. FreePassageDia. (mm)Capacity (Liters per minute) * Spray Angle Degree*1 3 7 101 2 3 4 5 7 10A B A B A B A B4.9VL 1.0 2.2 3.0 3.6 4.2 4.6 5.4 6.3 104 66 90 60 86 52 83 473/86.5VL 1.3 2.9 4.0 4.8 5.5 6.1 7.1 8.4 106 64 95 60 85 50 81 458.1VL 1.3 3.6 5.0 6.0 6.9 7.6 8.9 10.5 102 64 100 65 84 50 80 459.2VL 1.3 4.1 5.7 6.8 7.8 8.7 10.1 11.9 103 65 100 65 86 51 81 46Performance – Vaneless FullJet Nozzles*At the stated pressure in bar.Nozzle InletConn. NPTor BSPT (in.)CapacitySizeOrificeDia.Nom.(mm)Max.FreePassageDia. (mm)Capacity (Liters per minute)* Spray Angle Degree*0.3 0.5 1 1.5 2 3 4 5 6 7 0.5 1.5 61/43/81/25 2.8 2.0 1.3 1.6 2.3 2.8 3.2 3.9 4.6 5.1 5.6 6.0 68 75 827 3.2 2.4 1.9 2.3 3.2 3.9 4.5 5.5 6.4 7.1 7.8 8.4 68 75 828 4.0 2.8 2.2 2.6 3.6 4.5 5.2 6.3 7.3 8.2 8.9 9.6 75 80 8510 4.0 3.2 2.7 3.2 4.6 5.6 6.4 7.9 9.1 10.2 11.2 12.1 75 80 8511 4.0 3.6 3.0 3.5 5.0 6.1 7.1 8.7 10.0 11.2 12.3 13.3 75 80 8511 4.4 3.2 3.0 3.5 5.0 6.1 7.1 8.7 10.0 11.2 12.3 13.3 75 85 8313 4.4 3.6 3.5 4.2 5.9 7.3 8.4 10.3 11.9 13.3 14.5 15.7 75 85 8316 4.4 4.0 4.3 5.2 7.3 8.9 10.3 12.6 14.6 16.3 17.9 19.3 75 85 8320 5.6 4.4 5.4 6.4 9.1 11.2 12.9 15.8 18.2 20 22 24 75 85 8323 5.6 4.8 6.2 7.4 10.5 12.8 14.8 18.2 21 23 26 28 75 85 8326 6.0 5.2 7.0 8.4 11.9 14.5 16.8 21 24 27 29 31 75 85 8329 6.0 5.6 7.8 9.3 13.2 16.2 18.7 23 26 30 32 35 75 85 8333 7.5 6.0 8.9 10.6 15.0 18.4 21 26 30 34 37 40 75 85 8332 7.9 5.2 8.0 10.3 14.6 17.9 20 25 29 33 36 39 85 90 9540 7.9 6.0 10.0 12.9 18.2 22 26 32 36 41 45 48 85 90 9548 7.9 7.1 12.0 15.5 22 27 31 38 44 49 54 58 85 90 95°56 9.9 7.5 14.0 18.0 26 31 36 44 51 57 63 68 85 90 95°64 9.9 8.3 16.0 21 29 36 41 51 58 65 71 77 85 90 9572 9.9 9.1 18.0 23 33 40 46 57 66 73 80 87 85 90 95Maximum Free Passage Diameter is the maximum diameter as listed of foreign matter that can pass through the nozzle without clogging.Ordering InfoOval Spray Nozzle3/8 G – SS 4.9VLVaneless Spray Nozzle1/4 GANV – SS 10Inlet Nozzle Material CapacityConn. Type Code SizeInlet Nozzle Material CapacityConn. Type Code Size16

Cooling/CastingPerformance - DistriboJet Spray Nozzles 50°/65°/80°/95°*At the stated pressure in bar.NozzleInletConn.NPT orBSPT(in.)22-1/23Nozzle TypeRRRSpray Angle Degree* Spray Angle Degree*CapacitySizeOrificeDia.Nom.(mm)Capacity (Liters per minute)*50 65 80 95 50 65 80 95 1 3 5 7 10 15 20 30 40 60● ● 45 — 122 168 205 255 300 355 425 485 590 670● ● 45 — 122 168 205 255 300 355 425 485 590 670● ● 45 29 122 168 205 255 300 355 425 485 590 670● ● 60 — 163 225 270 340 400 470 570 650 780 890● ● 60 36.1 163 225 270 340 400 470 570 650 780 890● ● 70 — 190 260 315 400 465 550 660 760 910 1040● ● 70 — 190 260 315 400 465 550 660 760 910 1040● ● 70 36.5 190 260 315 400 465 550 660 760 910 1040● ● 90 — 245 335 405 510 600 710 850 970 1170 1330● ● 90 44.8 245 335 405 510 600 710 850 970 1170 1330● ● 110 — 300 410 495 630 730 860 1040 1190 1430 1630● ● 110 — 300 410 495 630 730 860 1040 1190 1430 1630● ● 110 46.4 300 410 495 630 730 860 1040 1190 1430 1630● ● 140 — 380 530 630 800 930 1100 1320 1510 1820 2070● ● 140 57.2 380 530 630 800 930 1100 1320 1510 1820 2070Performance – P45075*At the stated pressure in bar.Nozzle InletConn. NPT orBSPT (in.)1/43/8Nozzle No.OrificeDia. Nom.(mm)Max. FreePassageDia. (mm)Spray AngleCapacity (Liters per minute)*Degree*.7 1.4 2 2.8 4 5.5 7 20 80P45075-1/4H-4-65 1.9 1.2 1.6 2.2 2.6 3.1 3.6 4.2 4.5 65 65P45075-1/4H-5.5-65 2.1 1.3 2.1 3.0 3.6 4.2 4.9 5.5 6.0 65 65P45075-1/4H-7.5-45 2.5 1.3 2.9 4.1 5.0 5.7 6.8 7.7 8.4 45 45P45075-1/4H-7.5-65 2.5 1.3 2.9 4.1 5.0 5.7 6.8 7.7 8.4 65 65P45075-3/8H-3-65 1.5 1.0 1.0 1.5 1.8 2.1 2.3 2.7 3.0 65 65P45075-3/8H-3.5-65 1.5 1.0 1.0 1.5 1.8 2.1 2.3 2.7 3.0 65 65P45075-3/8H-4-65 1.8 1.2 1.6 2.2 2.6 3.1 3.6 4.2 4.5 65 65P45075-3/8H-5-65 2.1 1.6 1.7 2.5 3.0 3.5 4.3 4.9 5.5 65 65P45075-3/8H-5.5-65 2.1 1.3 2.1 3.0 3.6 4.2 4.9 5.5 6.0 65 65P45075-3/8H-7-45 2.1 1.3 2.1 3.0 3.6 4.2 4.9 5.5 6.0 45 45P45075-3/8H-7-65 2.1 1.3 2.1 3.0 3.6 4.2 4.9 5.5 6.0 65 65P45075-3/8H-8.5-65 2.6 1.6 3.2 4.6 5.6 6.4 7.5 8.5 9.3 65 65P45075-3/8H-10-45 2.9 2.8 3.6 5.1 6.1 7.0 8.7 9.4 10.3 45 55P45075-3/8H-10-65 2.8 1.6 3.6 5.1 6.1 7.0 8.7 9.4 10.3 65 65P45075-3/8H-14-60 2.8 1.6 3.6 5.1 6.1 7.0 8.7 9.4 10.3 60 60P45075-3/8H-22-60 4.2 3.0 8.2 11.4 13.2 14.9 17.4 19.5 22 60 55P45075-3/8H-22-90 4.2 3.0 8.2 11.4 13.2 14.9 17.4 19.5 22 90 87P45075-3/8H-7W-120 2.2 1.3 2.7 3.4 3.9 4.3 5.0 5.6 6.2 120 85Maximum Free Passage Diameter isthe maximum diameter as listed offoreign matter that can pass throughthe nozzle without clogging.Ordering InfoDistriboJet Spray Nozzle2 RR – SS 50 45P45075 Spray NozzleP45075 – 1/4H – SS – 4 – 65Inlet Nozzle Material Spray CapacityConn. Type Code Angle SizeNozzle Inlet Nozzle Material Capacity SprayPrefix Conn. Type Code Size Angle17

Cooling/CastingDimensions – Standard, Wide Angle, Square, Wide Angle SquareNozzle Type (Conn.)InletConn.(in.)A B C D L Net Weight(in.) (mm) (in.) (mm) (in. sq.) (mm sq.) (in.) (mm) (in.) (mm) (oz.) (kg)1/8 11/16 17.5 5/8 16 9/16 14.3 31/32 24.5 29/32 23 1-1/2 .04GA (F)1/4 7/8 22 25/32 20 11/16 17.5 1-7/32 31 1-5/32 29.5 2 .063/8 1 25.5 7/8 22 13/16 20.6 1-7/16 36.5 1-9/32 32.5 3-1/4 .091/2 1-17/32 39 1-1/16 27 1 25.4 2-1/32 51.5 1-9/16 40 6-1/4 181/8 11/16 17.5 21/32 16.5 9/16 14.3 31/32 24.5 15/16 24 1-1/2 .04GGA (M)1/4 7/8 22 13/16 20.5 11/16 17.5 1-1/4 32 1-5/32 29.5 2 .063/8 1 25.5 29/32 23 13/16 20.6 1-7/16 36.5 1-5/16 33.5 3-1/4 .091/2 1-17/32 39 1-1/8 28.5 1 25.4 2-1/32 51.5 1-5/8 41.5 6-1/4 .18Based on largest/heaviest version of each type.Dimensions – UniJet ® Nozzle with TG TipNozzle Type (Conn.)Length Hex. Net Weight(in.) (mm) (in.) (mm) (oz.) (kg)T+TG 1-31/32 50 13/16 20.6 2-1/2 .07TT+TG 1-31/32 50 13/16 20.6 2-1/4 .06Based on largest/heaviest version of each type.19

Cooling/CastingDimensions – OvalNozzle Type (Conn.)Inlet Conn.(in.)Length Hex. Net Weight(in.) (mm) (in.) (mm) (oz.) (kg)GVL 3/8 1-1/2 38 13/16 21 2 .06Based on largest/heaviest version of each type.Dimensions – DistriboJet ® 50°/65°/80°/95°Nozzle Type (Conn.)Inlet Conn.(in.)Length Dia. Net Weight(in.) (mm) (in.) (mm) (oz.) (kg)2 4-7/16 113 2-15/16 75 3 lbs 1.42-1/2 5-15/32 139 3-15/32 88 5-1/2 lbs 2.33 6-1/2 165 4-1/8 105 7-1/2 lbs 3.4R4 8-1/8 206 5 127 13-1/2 lbs 6.15 10-1/32 255 6-3/8 162 33 lbs 15.06 11-13/16 300 7-5/8 194 38-1/2 lbs 17.58 15-5/16 389 9-1/2 241 75 lbs 34.12 3-1/4 82.5 2-3/8 60 2 lbs .912-1/2 4 102 2-7/8 73 5-1/4 lbs 2.43 4-7/8 124 3-1/2 89 5-3/4 lbs 2.6RR4 6-1/2 165 4-1/2 114 10 lbs 4.55 8-1/8 206 5-9/16 141 25 lbs 11.46 9-3/4 248 6-5/8 168 29 lbs 13.28 13 330 8-5/8 219 56 lbs 25.5Based on largest/heaviest version of each type.Dimensions – VanelessNozzle Type (Conn.)InletConn.(in.)A B C D L Net Weight(in.) (mm) (in.) (mm) (in. sq.)(mmsq.)(in.) (mm) (in.) (mm) (oz.) (kg)GANV1/4 9/16 14.5 7/8 22.5 3/4 19 15/16 24 1-1/4 32 2-3/4 .083/8 11/16 17.5 31/32 25 7/8 22 1-1/8 28.5 1-13/32 36 3-3/4 .111/2 25/32 19.5 1-5/16 33.5 1 25.5 1-9-32 32.5 1-13/16 46 5-5/8 .161/4 9/16 14.5 7/8 22.5 3/4 19 15/16 24 1-1/4 32 2-1/2 .07GGANV3/8 11/16 17.5 31/32 25 7/8 22 1-1/8 28.5 1-13/32 36 3-1/2 .101/2 25/32 19.5 1-3/8 35 1 25.5 1-9-32 32.5 1-7/8 48 5-3/8 .15Based on largest/heaviest version of each type.20

Cooling/CastingDimensions – P45075P45075Inlet Conn.(in.)A B C Net Weight(in.) (mm) (in.) (mm) (in. ) (mm) (oz.) (gr.)1/4 1-3/32 28 13/16 20.6 3/4 19 1.9 543/8 1-3/64 26.5 7/8 22.2 53/64 21 1.9 54Based on largest/heaviest version of each type.Materials – Standard, Wide Angle, Square, Wide Angle Square, UniJet ®Nozzle TypeMaterialMaterial CodeG GG H HH GD GGD GA GGA TGBrass (none) ● ● ● ● ● ● ● ● ●Mild Steel I ● ● ● ● ● ● ● ●303 Stainless Steel SS ● ● ● ● ● ● ● ● ●316 Stainless Steel 316SS ● ● ● ●Polyvinyl Chloride PVC ● ● ● ●Cast: Brass (none) ●Cast: Cast Iron I ●Cast: 316 Stainless Steel SS ●Material options may vary by spray pattern type. Contact us for options.Materials – Vaneless, Oval DistriboJet ® 50°/65°/80°/95°/P45075Nozzle TypeMaterialMaterial CodeGANV GGANV G-VL GG-VL R RR P45075Brass (none) ● ● ● ● ● ● ●303 Stainless Steel SS ● ● ● ● ●316 Stainless Steel 316SS ● ●Cast: Cast Iron I ● ●21

Lubrication/Cooling/Strip Wash-OffVeeJet Flat Spray Nozzles ProvideMore Surface Contact for Efficientand Uniform CoolingWhen you need to remove heat during steel forming, our VeeJet spray nozzlesare called for. Providing a flat tapered-edge spray pattern, VeeJets efficiently anduniformly cool the entire width and length of the rolls using overlapping spray patterns.The greater surface contact of the sprays helps utilize available water andcontrols steel expansion and contraction and ultimately contour distortion.Our VeeJet nozzles offer the added advantage of being compact. This enables positioninga greater number of nozzles closer to the target to maximize heat removal,prevent scouring and extend roll life.Available in a wide variety of sizes, capacities, spray angles, materials and connectiontypes, VeeJet nozzles are often also used in cleaning and rinsing of pickledstrip after an acid bath.VeeJet Spray Nozzles – Efficient Heat Removal in Hot Strip andRolling Mill Applications; Effective Cleaning in Other AreasOur VeeJet flat spray nozzles produce a uniform distribution of small- to medium-size drops in a high-impactflat spray pattern with spray angles ranging from 15° to 110° at 40 psi (3 bar). Inlet connections range from1/8” to 1/2”, some with quick-connect spray tips. Most commonly used in roll cooling, VeeJet nozzles are alsoused in run-out tables, lubrication, strip wash and liquor flushing.H-VV H-VVL H-U1/8” to 1/4” NPT or BSPT (M)• H-VV VeeJet nozzles feature flowrates below 1 gpm at 40 psi (3.9l/min at 3 bar).• H-VV and H-VVL nozzles are availablewith spray angles of 15° to110° at 40 psi (3 bar).Integral strainer1/8” to 1/4” NPT or BSPT (M)• H-VVL VeeJet nozzles offer the sameflow rates as the H-VV but feature abuilt-in strainer.221/8” to 1/2” NPT or BSPT (M)• H-U VeeJet nozzles feature low flowrates of 1 gpm or greater at 40 psi(3.9 l/min at 3 bar).• H-U nozzles feature spray angles of15° to 110° at 40 psi (3 bar).

QuickLubrication/Cooling,Strip Wash-OffUniJet BodiesQuick VeeJetBodiesTypical spray nozzleassembly for QVVAand QUA spray tipsQuick VeeJetSpray TipsQUA/QLUAT Female body orTT male bodyQJA and QLJAfemale bodies orQuick VeeJet nozzle spray tip• QUA and QLUA spray tipsprovide flow rates of 1gpm or greater at 40 psi(3.9 l/min at 3 bar).Screen StrainerQJJA and QJJLAmale bodiesQVVASpray TipTip RetainerUniJet TPUSpray TipSpray tip• UniJet tips can beremoved and replacedwhile the nozzle bodyremains in position.• Spray tip orifices arerecessed to protectagainst damage.• Tips also feature unobstructedflow passage tominimize clogging.Spray tip• Quick VeeJet flat spray tipsoffer all the advantages ofstandard VeeJet nozzlesplus these time savingfeatures: quick connectionof tip to body that requiresa 1/4 turn and automaticspray pattern alignment.Brass versions of theQuick VeeJet nozzles havea Buna-N seal and 303stainless steel versions areequipped with a VITON®seal.Quick VeeJet nozzle spray tip• QVVA spray tips offer flowrates below 1 gpm at 40psi (3.9 l/min at 3 bar).23

Lubrication/Cooling/Strip Wash-OffPerformance – VeeJet Standard Nozzles*At the stated pressure in bar.SprayAngleDegreeat 3 bar11095Nozzle Type / Inlet Conn. (in.)H-VV H-VVL H-UCapacitySizeEquiv.OrificeDia.(mm.)Capacity (Liters per minute)*Spray AngleDegree*1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 .03 1 2 3 4 5 6 7 10 20 1.5 3 6● ● ● ● 01 .66 .12 .23 .32 .39 .46 .51 .56 .60 .72 1.0 94 110 121● ● ● ● 015 .81 .19 .34 .48 .56 .68 .76 .84 .90 1.1 1.5 97 110 121● ● ● ● 02 .89 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 98 110 120● ● ● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 99 110 120● ● ● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 100 110 119● ● ● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 100 110 118● ● ● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 101 110 117● ● ● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 102 110 117● ● ● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 103 110 117● ● ● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 104 110 117● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 105 110 117● ● 0050 .46 — — .16 .20 .23 .25 .28 .30 .36 .51 81 95 105● ● ● ● 01 .66 .12 .23 .32 .39 .46 .51 .56 .60 .72 1.0 81 95 105● ● ● 015 .81 .19 .34 .48 .59 .68 .76 .84 .90 1.1 1.5 82 95 105● ● ● ● 02 .89 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 82 95 105● ● ● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 83 95 104● ● ● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 84 95 103● ● ● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 84 95 102● ● ● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 86 95 101● ● ● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 87 95 100● ● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 89 95 100● ● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 90 95 100● ● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 90 95 100● ● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 91 95 101● ● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 92 95 100● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 93 95 99● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 93 95 99● ● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 93 95 99● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 93 95 99● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 93 95 9924

Lubrication/Cooling/Strip Wash-OffPerformance – VeeJet Standard Nozzles*At the stated pressure in bar.SprayAngleDegreeat 3 bar807365Nozzle Type / Inlet Conn. (in.)H-VV H-VVL H-UCapacitySizeEquiv.OrificeDia.(mm.)Capacity (Liters per minute)*Spray AngleDegree*1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 .03 1 2 3 4 5 6 7 10 20 1.5 3 6● ● ● ● 0050 .46 — .11 .16 .20 .23 .25 .28 .30 .36 .51 61 80 95● ● ● ● 0067 .53 — .15 .22 .26 .31 .34 .37 .40 .48 .68 67 80 94● ● ● ● 01 .66 — .23 .32 .39 .46 .51 .56 .60 .72 1.0 68 80 89● ● ● ● 015 .81 — .34 .48 .59 .68 .76 .84 .90 1.1 1.5 68 80 89● ● ● ● 02 .89 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 69 80 88● ● ● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 70 80 87● ● ● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 71 80 86● ● ● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 71 80 86● ● ● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 72 80 85● ● ● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 72 80 84● ● ● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 73 80 84● ● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 74 80 83● ● ● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 74 80 83● ● ● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 74 80 83● ● ● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 74 80 83● ● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 74 80 83● ● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 75 80 83● ● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 75 80 83● ● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 75 80 83● ● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 73 80 84● 200 8.7 25 46 64 79 91 102 112 121 144 205 74 80 82● ● 0231 .97 .29 .53 .74 .91 1.1 1.2 1.3 1.4 1.7 2.4 56 73 83● ● ● ● 0308 1.2 .38 .70 .99 1.2 1.4 1.6 1.7 1.9 2.2 3.1 58 73 82● ● ● 0462 1.4 .58 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.3 4.7 60 73 80● ● ● ● 0770 1.8 .96 1.8 2.5 3.0 3.5 3.9 4.3 4.6 5.5 7.8 64 73 77● ● ● ● 01 .66 — .23 .32 .39 .46 .51 .56 .60 .72 1.0 51 65 74● ● ● ● 015 .81 — .34 .48 .59 .68 .76 .84 .90 1.1 1.5 51 65 74● ● ● ● 02 .89 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 52 65 73● ● 025 .99 .31 .57 .81 .99 1.1 1.3 1.4 1.5 1.8 2.5 52 65 73● ● ● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 53 65 72● ● ● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 53 65 72● ● ● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 53 65 72● ● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 54 65 72● ● ● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 55 65 71● ● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 56 65 71● ● ● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 56 65 70● ● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 57 65 70● ● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 58 65 69● ● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 59 65 68● ● ● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 60 65 68● ● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 60 65 68● ● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 60 65 68● ● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 58 65 69● ● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 59 65 68● 200 8.7 25 46 64 79 91 102 112 121 144 205 60 65 6725

Lubrication/Cooling/Strip Wash-OffPerformance – VeeJet Standard Nozzles*At the stated pressure in bar.SprayAngleDegreeat 3 bar5040Nozzle Type / Inlet Conn. (in.)H-VV H-VVL H-UCapacitySizeEquiv.OrificeDia.(mm.)Capacity (Liters per minute)*Spray AngleDegree*1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 .03 1 2 3 4 5 6 7 10 20 1.5 3 6● ● ● ● 01 .66 — .23 .32 .39 .46 .51 .56 .60 .72 1.0 37 50 59● ● ● ● 02 .89 — .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 39 50 57● ● ● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 40 50 56● ● ● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 42 50 56● ● ● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 44 50 56● ● ● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 45 50 56● ● ● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 45 50 56● ● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 45 50 55● ● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 45 50 55● ● ● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 45 50 55● ● ● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 45 50 55● ● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 46 50 54● ● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 46 50 54● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 46 50 54● ● ● 70 5.1 8.7 16.0 23 28 32 36 39 42 50 71 46 50 54● ● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 44 50 52● 120 6.7 15.0 27 39 47 55 61 67 72 86 122 44 50 53● ● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 45 50 52● 200 8.7 25 46 64 79 91 102 112 121 144 205 46 50 52● ● ● ● 01 .66 — — .32 .39 .46 .51 .56 .60 .72 1.0 26 40 52● ● ● ● 015 .81 — — .48 .59 .68 .76 .84 .90 1.1 1.5 27 40 52● ● ● ● 02 .89 — .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 29 40 51● ● ● ● 03 1.1 — .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 30 40 50● ● ● ● 04 1.3 — .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 30 40 50● ● ● ● 05 1.4 — 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 31 40 49● ● ● ● 06 1.5 — 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 31 40 49● ● ● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 31 40 47● ● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 32 40 45● ● ● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 32 40 45● ● ● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 32 40 45● ● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 33 40 45● ● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 34 40 45● ● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 35 40 45● ● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 35 40 45● ● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 35 40 45● 80 5.5 10.0 18.2 26 32 36 41 45 48 58 82 35 40 44● ● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 34 40 43● ● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 35 40 43● 200 8.7 25 46 64 79 91 102 112 121 144 205 36 40 4226

Lubrication/Cooling/Strip Wash-OffPerformance – VeeJet Standard Nozzles*At the stated pressure in bar.SprayAngleDegreeat 3 bar2515Nozzle Type / Inlet Conn. (in.)H-VV H-VVL H-UCapacitySizeEquiv.OrificeDia.(mm.)Capacity (Liters per minute)*Spray AngleDegree*1/8 1/4 1/8 1/4 1/8 1/4 3/8 1/2 .03 1 2 3 4 5 6 7 10 20 1.5 3 6● ● ● ● 01 .66 — — .32 .39 .46 .51 .56 .60 .72 1.0 14 25 34● ● ● ● 02 .89 — .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 15 25 33● ● ● ● 03 1.1 — .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 15 25 33● ● ● ● 04 1.3 — .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 16 25 32● ● ● ● 05 1.4 — 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 16 25 32● ● ● ● 06 1.5 — 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 17 25 31● ● ● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 17 25 31● ● 10 2.0 — 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 18 25 31● ● ● 15 2.4 — 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 18 25 31● ● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 19 25 31● ● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 20 25 30● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 21 25 29● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 21 25 29● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 22 25 29● ● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 22 25 29● ● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 23 25 28● ● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 24 25 28● 200 8.7 25 46 64 79 91 102 112 121 144 205 24 25 26● ● ● ● 01 .66 — — .32 .39 .46 .51 .56 .60 .72 1.0 — 15 24● ● 02 .89 — — .64 .79 .91 1.0 1.1 1.2 1.4 2.0 6 15 22● ● ● ● 03 1.1 — — .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 6 15 22● ● ● ● 04 1.3 — — 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 7 15 21● ● ● ● 05 1.4 — — 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 7 15 21● ● ● ● 06 1.5 — 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 8 15 21● ● ● ● 08 1.8 — 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 9 15 20● ● 10 2.0 — 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 10 15 19● ● ● 15 2.4 — 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 10 15 19● ● ● 20 2.8 — 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 10 15 19● ● ● 30 3.4 — 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 10 15 19● ● ● 40 3.9 — 9.1 12.9 15.8 18.2 20 22 24 29 41 10 15 18● ● ● 50 4.4 — 11.4 16.1 19.7 23 25 28 30 36 51 11 15 18● ● 60 4.8 — 13.7 19.3 24 27 31 33 36 43 61 11 15 18● ● ● 70 5.2 — 16.0 23 28 32 36 39 42 50 71 11 15 18● ● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 13 15 17● 120 6.7 15.0 27 39 47 55 61 67 72 86 122 13 15 17● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 14 15 17● 200 8.7 25 46 64 79 91 102 112 121 144 205 14 15 17Ordering InfoVeeJet Spray NozzleH 1/4 VV – SS 110 10Nozzle Inlet Nozzle Material Spray CapacityPrefix Conn. Type Code Angle Size27

Lubrication/Cooling,Strip Wash-OffQuickPerformance – Quick VeeJet and UniJet Nozzles*At the stated pressure in bar.SprayAngleat 3 bar1109580Quick FullJet TipsUniJetTipCapacitySizeEquiv.OrificeDiam.(mm.)Capacity (Liters per minute)*Spray AngleDegree*QVVA QUA QLUA TPU 0.3 1 2 3 4 5 6 7 10 20 1.5 3 6● 01 .66 .12 .23 .32 .39 .46 .51 .56 .60 .72 1.0 94 110 121● 015 .81 .19 .34 .48 .59 .68 .76 .84 .90 1.1 1.5 97 110 121● ● 02 .91 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 98 110 120● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 99 110 120● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 100 110 119● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 100 110 118● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 101 110 117● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 102 110 117● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 103 110 117● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 104 110 117● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 105 110 117● 0050 7.5 18.7 34 48 59 68 76 84 90 108 153 93 95 99● ● 01 .66 .12 .23 .32 .39 .46 .51 .56 .60 .72 1.0 81 95 105● ● 015 .81 .19 .34 .48 .59 .68 .76 .84 .90 1.1 1.5 82 95 105● ● 02 .91 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 82 95 105● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 83 95 104● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 84 95 103● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 84 95 102● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 86 95 101● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 87 95 100● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 89 95 100● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 90 95 100● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 90 95 100● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 91 95 101● ● 40 3.8 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 92 95 100● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 93 95 99● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 93 95 99● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 93 95 99● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 93 95 99● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 93 95 99● ● 0050 .46 — .11 .16 .20 .23 .25 .28 .30 .36 .51 61 80 95● ● 0067 .53 — .15 .22 .26 .31 .34 .37 .40 .48 .68 67 80 94● ● 01 .66 — .23 .32 .39 .46 .51 .56 .60 .72 1.0 68 80 89● ● 015 .81 — .34 .48 .59 .68 .76 .84 .90 1.1 1.5 68 80 89● ● 02 .91 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 69 80 88● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 70 80 87● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 71 80 86● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 71 80 86● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 72 80 85● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 72 80 84● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 73 80 84● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 74 80 83● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 74 80 83● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 74 80 83● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 74 80 83● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 74 80 83● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 75 80 83● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 75 80 83● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 75 80 83● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 75 80 84● 200 8.7 25 46 64 79 91 102 112 121 144 205 74 80 8228

QuickPerformance – Quick VeeJet and UniJet NozzlesLubrication/Cooling,Strip Wash-Off*At the stated pressure in bar.SprayAngleat 3 bar736550Quick FullJet TipsUniJetTipCapacitySizeEquiv.OrificeDiam.(mm.)Capacity (Liters per minute)*Spray AngleDegree*QVVA QUA QLUA TPU 0.3 1 2 3 4 5 6 7 10 20 1.5 3 6● ● 0231 .96 .29 .53 .74 .91 1.1 1.2 1.3 1.4 1.7 2.4 56 73 83● ● 0308 1.1 .38 .70 .99 1.2 1.4 1.6 1.7 1.9 2.2 3.1 58 73 82● ● 0462 1.4 .58 1.1 1.5 1.8 2.1 2.4 2.6 2.8 3.3 4.7 60 73 80● ● 0770 1.7 .96 1.8 2.5 3.0 3.5 3.9 4.3 4.6 5.5 7.8 64 73 77● ● 01 .66 — .23 .32 .39 .46 .51 .56 .60 .72 1.0 51 65 74● ● 015 .81 — .34 .48 .59 .68 .76 .84 .90 1.1 1.5 51 65 74● ● 02 .91 .25 .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 52 65 73● 025 .99 .31 .57 .81 .99 1.1 1.3 1.4 1.5 1.8 2.5 80 65 73● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 53 65 72● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 53 65 72● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 53 65 72● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 54 65 72● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 55 65 71● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 56 65 71● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 56 65 70● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 57 65 70● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 58 65 69● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 59 65 68● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 60 65 68● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 60 65 68● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 60 65 68● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 58 65 68● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 59 65 68● 200 8.7 25 46 64 79 91 102 112 121 144 205 60 65 67● ● 01 .66 — .23 .32 .39 .46 .51 .56 .60 .72 1.0 37 50 59● ● 02 .91 — .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 39 50 57● ● 03 1.1 .37 .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 40 50 56● ● 04 1.3 .50 .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 42 50 56● ● 05 1.4 .62 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 44 50 56● ● 06 1.5 .75 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 45 50 56● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 45 50 55● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 45 50 55● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 45 50 55● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 45 50 55● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 45 50 55● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 46 50 54● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 46 50 54● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 46 50 54● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 46 50 54● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 44 50 52● 120 6.7 15.0 27 39 47 55 61 67 72 86 122 44 50 53● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 45 50 52● 200 8.7 25 46 64 79 91 102 112 121 144 205 46 50 5229

Lubrication/Cooling,Strip Wash-OffQuickPerformance – Quick VeeJet and UniJet Nozzles*At the stated pressure in bar.SprayAngleat 3 bar4025Quick FullJet TipsUniJetTipCapacitySizeEquiv.OrificeDiam.(mm.)Capacity (Liters per minute)*Spray AngleDegree*QVVA QUA QLUA TPU 0.3 1 2 3 4 5 6 7 10 20 1.5 3 6● ● 01 .66 — — .32 .39 .46 .51 .56 .60 .72 1.0 26 40 52● ● 015 .81 — — .48 .59 .68 .76 .84 .90 1.1 1.5 27 40 52● ● 02 .91 — .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 29 40 51● ● 03 1.1 — .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 30 40 50● ● 04 1.3 — .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 30 40 50● 05 1.4 — 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 31 40 49● ● 06 1.5 — 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 31 40 49● ● 08 1.8 1.0 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 31 40 47● ● 10 2.0 1.2 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 32 40 45● ● 15 2.4 1.9 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 32 40 45● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 32 40 45● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 33 40 45● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 34 40 45● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 35 40 45● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 35 40 45● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 35 40 45● 80 5.5 10.0 18.2 26 32 36 41 45 48 58 82 35 40 44● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 34 40 43● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 35 40 43● 200 8.7 25 46 64 79 91 102 112 121 144 205 36 40 42● ● 01 .66 — — .32 .39 .46 .51 .56 .60 .72 1.0 14 25 34● ● 02 .91 — .46 .64 .79 .91 1.0 1.1 1.2 1.4 2.0 15 25 33● ● 03 1.1 — .68 .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 15 25 33● ● 04 1.3 — .91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 16 25 32● ● 05 1.4 — 1.1 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 16 25 32● ● 06 1.5 — 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 17 25 31● ● 08 1.8 — 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 17 25 31● ● 10 2.0 — 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 18 25 31● ● 15 2.4 — 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 18 25 31● ● 20 2.8 2.5 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 19 25 31● ● 30 3.4 3.7 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 20 25 30● ● 40 3.9 5.0 9.1 12.9 15.8 18.2 20 22 24 29 41 21 25 29● ● 50 4.4 6.2 11.4 16.1 19.7 23 25 28 30 36 51 21 25 29● ● 60 4.8 7.5 13.7 19.3 24 27 31 33 36 43 61 22 25 29● ● 70 5.2 8.7 16.0 23 28 32 36 39 42 50 71 22 25 29● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 23 25 28● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 24 25 28● 200 8.7 25 46 64 79 91 102 112 121 144 205 24 25 2630

QuickPerformance – Quick VeeJet and UniJet NozzlesLubrication/Cooling,Strip Wash-Off*At the stated pressure in bar.SprayAngleat 3 bar15Quick FullJet TipsUniJetTipCapacitySizeEquiv.OrificeDiam.(mm.)Capacity (Liters per minute)*Spray AngleDegree*QVVA QUA QLUA TPU 0.3 1 2 3 4 5 6 7 10 20 1.5 3 6● ● 01 .66 — — .32 .39 .46 .51 .56 .60 .72 1.0 — 15 24● ● 02 .91 — — .64 .79 .91 1.0 1.1 1.2 1.4 2.0 6 15 22● ● 03 1.1 — — .97 1.2 1.4 1.5 1.7 1.8 2.2 3.1 6 15 22● ● 04 1.3 — — 1.3 1.6 1.8 2.0 2.2 2.4 2.9 4.1 7 15 21● ● 05 1.4 — — 1.6 2.0 2.3 2.5 2.8 3.0 3.6 5.1 7 15 21● ● 06 1.6 — 1.4 1.9 2.4 2.7 3.1 3.3 3.6 4.3 6.1 8 15 21● ● 08 1.8 — 1.8 2.6 3.2 3.6 4.1 4.5 4.8 5.8 8.2 9 15 20● ● 10 2.0 — 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 10.2 10 15 19● ● 15 2.5 — 3.4 4.8 5.9 6.8 7.6 8.4 9.0 10.8 15.3 10 15 19● ● 20 2.8 — 4.6 6.5 7.9 9.1 10.2 11.2 12.1 14.4 20 10 15 19● ● 30 3.4 — 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 31 10 15 19● ● 40 3.9 — 9.1 12.9 15.8 18.2 20 22 24 29 41 10 15 18● ● 50 4.4 — 11.4 16.1 19.7 23 25 28 30 36 51 11 15 18● 60 4.8 — 13.7 19.3 24 27 31 33 36 43 61 11 15 18● ● 70 5.2 — 16.0 23 28 32 36 39 42 50 71 11 15 18● 100 6.2 12.5 23 32 39 46 51 56 60 72 102 13 15 17● 120 6.8 15.0 27 39 47 55 61 67 72 86 122 13 15 17● 150 7.5 18.7 34 48 59 68 76 84 90 108 153 14 15 17● 200 8.7 25 46 64 79 91 102 112 121 144 205 14 15 17Ordering InfoQuickJet Spray NozzleNozzle BodySpray Tip1/4 QJJA – SS+QVVA – SS 110 10Inlet Body MaterialConn. Type CodeTip Material Spray CapacityType Code Angle Size31

Lubrication/Cooling,Strip Wash-OffQuickDimensions – VeeJet NozzlesNozzle Type (Conn.)Inlet Conn.(in.)Length Hex. Net Weight(in.) (mm) (in.) (mm) (oz.) (kg)H-VV(M)1/8 7/8 22 1/2 12.7 1/2 .0141/4 29/32 23 9/16 14.3 3/4 .021/8 1-13/32 36 1/2 12.7 3/4 .02H-VVL(M)1/4 1-1/2 38 9/16 14.3 1 .031/8 7/8 22 1/2 12.7 1/2 .014H-U(M)1/4 1 25 9/16 14.3 3/4 .023/8 1-1/4 32 11/16 17.5 1-1/2 .041/2 1-1/2 38 7/8 22.2 2-1/4 .06Based on largest/heaviest version of each type.Body Types – Quick VeeJet NozzlesStandard BodyInlet Conn. (in.)Conn. FConn. MQJA QJLA QJJA QJJLA1/8 ● ●1/4 ● ●3/8 ● ● ● ●1/2 ● ● ● ●32

QuickLubrication/Cooling,Strip Wash-OffDimensions – Quick VeeJet NozzlesNozzle TypeLength Hex. Net Weight(in.) (mm) (in.) (mm) (oz.) (kg)QJA+QVVA 2-5/32 55 1 25.4 2/1/2 .07QJJA+QVVA 2-1/16 53 1 25.4 2 .06QJA+QUA 2 51 1 25.4 2-3/4 .08QJJLA+QUA 1-29/32 49 1 25.4 2-1/4 .06QJLA+QLUA 2-5/16 59 1-1/8 28.6 4-3/4 .13QJJLA+QLUA 2-11/32 60 1-1/8 28.6 4-1/4 .12Based on largest/heaviest version of each type.Dimensions – UniJet Nozzle with TPU TipNozzle TypeLength Hex. Net Weight(in.) (mm) (in.) (mm) (oz.) (kg)T+TPU 1-57/64 48 13/16 20.6 2-1/4 .06TT+TPU 1-57/64 48 13/16 20.6 2 .06Based on largest/heaviest version of each type.Materials – VeeJet NozzlesMaterialMaterial CodeNozzle TypeH-VV H-VVL H-U QVVA QUA QLUA TPUBrass (none) ● ● ● ● ● ● ●Mild Steel I ● ●303 Stainless Steel SS ● ● ● ● ● ● ●316 Stainless Steel 316SS ● ● ●Polyvinyl Chloride PVC ●33

Lubrication/Cooling/Strip Wash-OffDovetailDovetail VeeJet Nozzles – Consistent, RepeatableSprays Contribute to Improved Steel QualityThe dovetail groove feature of our 1/4” and 3/8” Dovetail VeeJet nozzles is whatprovides the repeatable pattern positioning without an elastomeric seal. The selfaligning,interchangeable spray tips slide into the groove with the spray patternoffset by 5° ensuring exact alignment every time after nozzle disassembly. Thespray tip slides into the body and stays in place, making it easy to slip the capon and secure the tip.Specifications:• Small capacity versions range from .067 to .80 gpmat 40 psi (.26 to 3.03 l/min at 3 bar)• Large capacity versions range from .80 to 7 gpm at40 psi (3.03 to 27.63 l/min at 3 bar)• Brass, 303 or 316 stainless steel material options• Spray angles of 65°, 80°, 95° and 110°• 1/4” and 3/8” nozzle bodies are available withmale, female or weld connectionsOrdering InfoDovetail VeeJet Spray Nozzle49805 – 3/8M – SS + 49807 – SS 6504Assembly Nozzle Body Nozzle Tip Material SprayNo. Material No. Code No.Dimensions – 1 /4" 50870 DovetailDimensions – 3 /8" 49805 Dovetail34

DovetailLubrication/Cooling/Strip Wash-OffPerformance – 1 /4" & 3 /8" Dovetail Nozzles*At the stated pressure in bar.Spray Nozzle No.Capacity (Liters per minute)*2 3 4 5.5 7 10Spray AngleDegree at3 barSpray Nozzle No.Capacity (Liters per minute)*2 3 4 5.5 7 10Spray AngleDegree at3 bar49805-3/8-050150870-1/4-050149805-3/8-150150870-1/4-150149805-3/8-25006750870-1/4-25006749805-3/8-2501550870-1/4-2501549805-3/8-6501550870-1/4-6501549805-3/8-650250870-1/4-650249805-3/8-650450870-1/4-650449805-3/8-650650870-1/4-650649805-3/8-650850870-1/4-650849805-3/8-800150870-1/4-800149805-3/8-800250870-1/4-800249805-3/8-800450870-1/4-800449805-3/8-800650870-1/4-800649805-3/8-800850870-1/4-800849805-3/8-950250870-1/4-950249805-3/8-950450870-1/4-950449805-3/8-950650870-1/4-950649805-3/8-950850870-1/4-950849805-3/8-110006750870-1/4-110006749805-3/8-1100250870-1/4-1100249805-3/8-1100450870-1/4-1100449805-3/8-1100650870-1/4-1100649805-3/8-1100850870-1/4-11008.34 .40 .45 .53 .61 .71 5.34 .40 .45 .53 .61 .71 15.23 .26 .30 .34 .42 .48 25.49 .60 .67 .79 .91 1.07 25.49 .60 .67 .79 .91 1.07 65.64 .79 .91 1.06 1.20 1.40 651.30 1.60 1.80 2.16 2.40 2.90 651.90 2.40 2.70 3.22 3.60 4.30 652.60 3.20 3.60 4.28 4.80 5.80 65.26 .38 .45 .53 .61 .72 80.64 .79 .91 1.06 1.20 1.40 801.30 1.60 1.80 2.16 2.40 2.90 801.90 2.40 2.70 3.22 3.60 4.30 802.60 3.20 3.60 4.28 4.80 5.80 80.64 .79 .91 1.06 1.20 1.40 951.30 1.60 1.80 2.16 2.40 2.90 951.90 2.40 2.70 3.22 3.60 4.30 952.60 3.20 3.60 4.28 4.80 5.80 95.23 .26 .30 .34 .42 .48 110.64 .79 .91 1.06 1.20 1.40 1101.30 1.60 1.80 2.16 2.40 2.90 1101.90 2.40 2.70 3.22 3.60 4.30 1102.60 3.20 3.60 4.28 4.80 5.80 11049805-3/8-405050870-1/4-405049805-3/8-503050870-1/4-503049805-3/8-505050870-1/4-505049805-3/8-507050870-1/4-507049805-3/8-605050870-1/4-605049805-3/8-651050870-1/4-651049805-3/8-651550870-1/4-651549805-3/8-652050870-1/4-652049805-3/8-653050870-1/4-653049805-3/8-654050870-1/4-654049805-3/8-655050870-1/4-655049805-3/8-755050870-1/4-755049805-3/8-801050870-1/4-801049805-3/8-801550870-1/4-801549805-3/8-802050870-1/4-802049805-3/8-803050870-1/4-803049805-3/8-804050870-1/4-804049805-3/8-805050870-1/4-805049805-3/8-951050870-1/4-951049805-3/8-951550870-1/4-951549805-3/8-952050870-1/4-952049805-3/8-953050870-1/4-953049805-3/8-954050870-1/4-954016.11 19.73 22.78 27.90 30.13 36.02 459.66 11.83 13.66 16.73 18.07 21.60 5016.11 19.73 22.78 27.90 30.13 36.02 5022.56 27.63 31.91 37.42 42.22 50.46 5016.11 19.73 22.78 27.90 30.13 36.02 603.22 3.95 4.56 5.35 6.03 7.21 654.82 5.92 6.84 8.02 9.08 10.81 656.44 7.89 9.11 11.16 12.05 14.41 659.66 11.83 13.66 16.73 18.07 21.60 6512.88 15.78 18.22 22.31 24.10 28.80 6516.11 19.73 22.78 27.90 30.13 36.02 6516.11 19.73 22.78 27.90 30.13 36.02 753.22 3.95 4.56 5.35 6.03 7.21 804.82 5.92 6.84 8.02 9.08 10.81 806.44 7.89 9.11 11.16 12.05 14.41 809.66 11.83 13.66 16.73 18.07 21.60 8012.88 15.78 18.22 22.31 24.10 28.80 8016.11 19.73 22.78 27.90 30.13 36.02 803.22 3.95 4.56 5.35 6.03 7.21 954.82 5.92 6.84 8.02 9.08 10.81 956.44 7.89 9.11 11.16 12.05 14.41 959.66 11.83 13.66 16.73 18.07 21.60 9512.88 15.78 18.22 22.31 24.10 28.80 9549805-3/8-955050870-1/4-955016.11 19.73 22.78 27.90 30.13 36.02 9549805-3/8-1104050870-1/4-1104012.88 15.78 18.22 22.31 24.10 28.80 11049805-3/8-1105050870-1/4-1105016.11 19.73 22.78 27.90 30.13 36.02 11035

Lubrication/Cooling,Strip Wash-Off18897 Dovetail18897 Dovetail VeeJet Nozzles – Repeatable,Dependable Performance in High TemperatureRoll CoolingSimilar to our 1/4” and 3/8” Dovetail VeeJet nozzles, the 18897 Dovetail VeeJet is aself-aligning nozzle ensuring performance remains unaltered after replacement ormaintenance. In just a matter of seconds, tips can be changed. Simply loosen thecap, replace the tip and replace the cap to secure the tip.The spray pattern is offset by 15° from the dovetail axis for trouble-free performance.Nozzle bodies fitted with metal seals are welded into the header. Sinceelastomeric seals are not used, 18897 Dovetail VeeJet nozzles are ideal for hightemperature applications.Specifications:• Capacities range from 2 to 20 gpm at 40 psi (7.6 to 75.7 l/min at 3 bar)• Weld and standard body connection options• Brass, 303 stainless steel and hardened stainless steel material optionsDimensions Ordering Info18897 Dovetail VeeJet Spray Nozzle18897 – 5050 SSSpray Tip Spray Tip Tip MaterialPrefix Size Code36

18897 DovetailPerformance — 18897 Dovetail NozzlesLubrication/Cooling,Strip Wash-Off*At the stated pressure in bar.Spray Tip No.Equiv.Capacity (Liters per minute)* Spray Angle Degree*Spray TipOrificeSpray Tip SizePrefixDia. (mm) 0.5 1 2 4 6 8 10 3 518897-18897-18897-18897-1520 2.8 3.2 4.6 6.4 9.1 11.2 12.9 14.4 15 191525 3.2 4.0 5.7 8.1 11.4 14.0 16.1 18.0 15 191530 3.6 4.8 6.8 9.7 13.7 16.7 19.3 22 15 191540 4.0 6.4 9.1 12.9 18.2 22 26 29 15 191550 4.4 8.1 11.4 16.1 23 28 32 36 15 191560 4.8 9.7 13.7 19.3 27 33 39 43 15 191580 5.6 12.9 18.2 26 36 45 52 58 15 1915120 6.8 19.3 27 39 55 67 77 86 15 172520 2.8 3.2 4.6 6.4 9.1 11.2 12.9 14.4 25 322525 3.2 4.0 5.7 8.1 11.4 14.0 16.1 18.0 25 322530 3.6 4.8 6.8 9.7 13.7 16.7 19.3 22 25 322540 4.0 6.4 9.1 12.9 18.2 22 26 29 25 322550 4.4 8.1 11.4 16.1 23 28 32 36 25 322560 4.8 9.7 13.7 19.3 27 33 39 43 25 332580 5.6 12.9 18.2 26 36 45 52 58 25 3325100 6.4 16.2 23 32 46 56 64 72 25 3325120 6.8 19.3 27 39 55 67 77 86 25 3325200 8.7 32 46 64 91 112 129 144 25 334020 2.8 3.2 4.6 6.4 9.1 11.2 12.9 14.4 40 454025 3.2 4.0 5.7 8.1 11.4 14.0 16.1 18.0 40 454030 3.6 4.8 6.8 9.7 13.7 16.7 19.3 22 40 454040 4.0 6.4 9.1 12.9 18.2 22 26 29 40 454050 4.4 8.1 11.4 16.1 23 28 32 36 40 434060 4.8 9.7 13.7 19.3 27 33 39 43 40 434080 5.6 12.9 18.2 26 36 45 52 58 40 434090 6.0 14.6 21 29 41 50 58 65 40 4340100 6.4 16.2 23 32 46 56 64 72 40 4340120 6.8 19.3 27 39 55 67 77 86 40 4340200 8.7 32 46 64 91 112 129 144 40 445020 2.8 3.2 4.6 6.4 9.1 11.2 12.9 14.4 50 555025 3.2 4.0 5.7 8.1 11.4 14.0 16.1 18.0 50 545030 3.6 4.8 6.8 9.7 13.7 16.7 19.3 22 50 545040 4.0 6.4 9.1 12.9 18.2 22 26 29 50 535050 4.4 8.1 11.4 16.1 23 28 32 36 50 535060 4.8 9.7 13.7 19.3 27 33 39 43 50 535080 5.6 12.9 18.2 26 36 45 52 58 50 5350120 6.8 19.3 27 39 55 67 77 86 50 5350200 8.7 32 46 64 91 112 129 144 50 5237

Lubrication/Cooling,Strip Wash-OffPerformance — 18897 Dovetail Nozzles18897 Dovetail*At the stated pressure in bar.Spray Tip No.Equiv.Capacity (Liters per minute)* Spray Angle Degree*Spray TipOrificeSpray Tip SizePrefixDia. (mm) 0.5 1 2 4 6 8 10 3 518897-18897-18897-6520 2.8 3.2 4.6 6.4 9.1 11.2 12.9 14.4 65 726525 3.2 4.0 5.7 8.1 11.4 14.0 16.1 18.0 65 726530 3.6 4.8 6.8 9.7 13.7 16.7 19.3 22 65 726540 4.0 6.4 9.1 12.9 18.2 22 26 29 65 726550 4.4 8.1 11.4 16.1 23 28 32 36 65 736560 4.8 9.7 13.7 19.3 27 33 39 43 65 736580 5.6 12.9 18.2 26 36 45 52 58 65 7465100 6.4 16.2 23 32 46 56 64 72 65 7265120 6.8 19.3 27 39 55 67 77 86 65 6965200 8.7 32 46 64 91 112 129 144 65 698020 2.8 3.2 4.6 6.4 9.1 11.2 12.9 14.4 80 838025 3.2 4.0 5.7 8.1 11.4 14.0 16.1 18.0 80 848030 3.6 4.8 6.8 9.7 13.7 16.7 19.3 22 80 848040 4.0 6.4 9.1 12.9 18.2 22 26 29 80 858050 4.4 8.1 11.4 16.1 23 28 32 36 80 858060 4.8 9.7 13.7 19.3 27 33 39 43 80 868080 5.6 12.9 18.2 26 36 45 52 58 80 8980120 6.8 19.3 27 39 55 67 77 86 80 8380200 8.7 32 46 64 91 112 129 144 80 8211020 2.8 3.2 4.6 6.4 9.1 11.2 12.9 14.4 110 11711025 3.2 4.0 5.7 8.1 11.4 14.0 16.1 18.0 110 11711030 3.6 4.8 6.8 9.7 13.7 16.7 19.3 22 110 11711040 4.0 6.4 9.1 12.9 18.2 22 26 29 110 11711050 4.4 8.1 11.4 16.1 23 28 32 36 110 11711060 4.8 9.7 13.7 19.3 27 33 39 43 110 11611080 5.6 12.9 18.2 26 36 45 52 58 110 116110120 6.8 19.3 27 39 55 67 77 86 110 116110200 8.7 32 46 64 91 112 129 144 110 11638

XTLubrication/Cooling/Strip Wash-OffDramatically Increase Cooling Efficiency withour Extra-Thick (XT) VeeJet NozzlesUsing open passages, the XT VeeJet nozzle provides a wider flat footprint– 30” (762 mm) – than other nozzles. This increased surface contactresults in better cooling efficiency. Plus, the compact size of the nozzleenables positioning for greater spray overlap. The result? Maximum heatremoval, increased production and better steel quality.The spray of the XT VeeJet nozzle is offset 20° to prevent spray interference.Interchangeable with most spray tips used in many cooling operations, the XTVeeJet nozzles offer an easy way to increase cooling efficiency without majorline retooling or expensive equipment upgrades. And, similar to our other dovetailnozzles, the XT VeeJet is self-aligning and features a one-piece construction thateliminates internal obstructions, prevents clogging and simplifies maintenance.Specifications:• Capacities range from 2 to 12 gpm at 40 psi (7.6 to 45.4 l/min at 3 bar)• Spray angle options of 65° or 80°• Brass or 303 stainless steel construction• Weld and standard body connection optionsPerformance*At the stated pressure in bar.Spray TipNo. 49784-Capacity (Liters per minute)*2 3 4 5.5 7 10XT___-___20 6.44 7.89 9.11 11.16 12.05 14.41XT___-___30 9.66 11.83 13.66 16.73 18.07 21.60XT___-___40 12.88 15.78 18.22 22.31 24.10 28.80XT___-___50 16.11 19.73 22.78 27.90 30.13 36.02XT___-80120 38.61 47.66 53.68 62.12 68.97 81.01Spray AngleNozzle No.49784-Spray AngleDegree“A”XT___-65___ 65XT___-80___ 80“B”30Ordering InfoXT VeeJet Spray Nozzle49784 – XT – SS 65 4039Nozzle Material Spray CapacityNo. Code Angle No.

Lubrication/Cooling,Strip Wash-OffRectangular VeeJet Nozzles ProvideThick Sprays and Uniform CoolingFor other cooling operations that require uniform cooling,our Rectangular VeeJet nozzles provide even distributionof a thick spray pattern. Using a smaller orifice than our XTVeeJet nozzles, Rectangular VeeJets minimize fluttering, maximizecooling efficiency and enhance steel quality.Specifications:• Capacities range from 10 to 59 gpm at 40 psi(37.9 to 223 l/min at 3 bar)• Brass or 303 stainless steel material options• Weld and standard body connection optionsRectangularOrdering InfoRectangular VeeJet Spray Nozzle25381 - SS - 28 - 90/20Nozzle Material Capacity SprayNo. Code Size AngleDimensionsPerformanceSpray Tip No.Capacity (Liters per minute)*Spray AngleDegree at 3 bar2 3 5 7 14 A B25381-6-90/2090 201.7 2.3 2.8 3.3 4.925381-6-70/20 70 2025381-8-90/2090 202.2 3.0 3.7 4.5 6.125381-8-70/20 70 2025381-9-90/2090 202.5 3.4 4.5 6.1 6.625381-9-70/20 70 2025381-13-90/2090 2025381-13-70/30 3.5 4.9 6.4 7.0 9.1 70 3025381-13-70/20 70 2025381-14-90/2090 2025381-14-70/30 4.2 5.7 6.8 7.9 11.0 70 3025381-14-70/20 70 2025381-19-90/2090 2025381-19-70/205.3 6.8 9.5 10.6 14.870 2025381-21-90/2090 2025381-21-70/30 6.1 7.9 10.2 12.11 17.0 70 3025381-21-70/20 70 20Spray Tip No.25381-28-90/20Capacity (Liters per minute)**At the stated pressure in bar.Spray AngleDegree at 3 bar2 3 5 7 14 A B90 2025381-28-70/30 7.2 9.8 13.6 15.9 22.3 70 3025381-28-70/20 70 2025381-35-90/2090 2025381-35-70/30 9.5 13.2 17.0 19.7 27.3 70 3025381-35-70/20 70 2025381-46-90/2090 2025381-46-70/30 12.9 17.4 22.3 26.1 34.1 70 3025381-46-70/20 70 2025381-61-90/2090 2025381-61-70/30 17.0 23.1 29.9 34.1 47.3 70 3025381-61-70/20 70 2025381-100-90/2025381-100-70/3025381-100-70/2027.6 37.9 53.0 58.7 76.190 2070 3070 2040

DescaleJet ®Descaling/Hot Strip MillDescaleJet Nozzles:High Impact and Long Wear-LifeDescaling is another critical component when ensuring steel quality. High-impactspray nozzles are used to remove the scale that is formed during rolling. Our lineof DescaleJet nozzles offers more than 50% greater impact force than conventionalnozzles and provides a fine finish. They also offer long wear-life to extend theintervals between maintenance/replacement and make efficient use of water tokeep operating costs low.Choose from our full range of standard DescaleJet nozzles or our AA214DescaleJet for high-pressure, low-flow, thin slab descaling.41

Descaling/Hot Strip MillDescaleJet ®Unique Two-Axis Impact Tester ProvidesMore Precise Performance TestingDecades of experience in spray technology have enabled us tolead the way in development of innovative new products forthe steel industry. Our engineers are continually working onnew designs to improve performance in a variety of applications.During the development process, new product prototypesare put through rigorous testing in our spray laboratories. Fortesting our descaling nozzles, we even developed a unique measuringdevice to obtain the performance data we required.Our impact tester collects data in two axes. The load cell firstmoves to the outside of the spray pattern. Then it transversesthrough the spray, taking measurements at intervalsalong the way. The load cell keeps going back andforth through the spray until the entire spray area hasbeen covered. When the test is complete, a data matrixis available for further analysis.In addition to using our impact tester in our ownresearch and development, we use it frequently whenworking with customers to troubleshoot spray problemsor in proof-of-concept testing for specializedrequirements.This display shows a 3-D image of the datataken. The units are in force pounds. Each colorshows a range of data and illustrates the amountof data collected.This graph shows the lateral distribution. Each bar on the graph isone row in the transverse direction through the spray and shows themaximum impact for each row. Note the even coverage produced byour DescaleJet nozzles.42

AutoJet ® Technologies is the turnkey systems divisionof Spraying Systems Co. Our systems ensurethat you obtain the very best performance possiblefrom your spray nozzles. That can only happen if yourentire spray system operates efficiently, so our systemscontrol all components – nozzles, pumps, sensorsand other hydraulic and pneumatic components.Your spray system is a small but important part ofyour steelmaking operation. Nozzle performance canhave a tremendous impact on steel quality and operatingcosts.That’s why our spray controllers and systems aredesigned to yield process improvements with fastpayback. In fact, automating your spray applicationcan often pay for itself in just a few months by:• Improving product quality through precise and uniformcooling, cleaning and coating• Reducing manual labor by minimizing set-up,maintenance and monitoring of spray systemoperation• Improving regulatory compliance and emissioncontrolFor maximum flexibility, AutoJet Spray Systemscan operate independently or can be integratedwith other plant control systems.43

45Photos courtesy of UnitedStates Steel Corporationand MACSTEEL ® .

Gas Conditioning: Reduce Gas Temperatureand Volume Prior to Baghouse EntryA major producer of hot-rolled, cold-rolled and coatedsheets turned to AutoJet ® Technologies for a gas conditioningsystem that would:• Reliably and effectively reduce gas temperature,humidity and volume to prevent damage to baghousefilters, ensure efficient baghouse operation and maximizeuptime• Lower gas temperature without wetting ducts toensure maximum air flow and prevent sludge fromforming and creating maintenance problems andincreased disposal costsThe turnkey solution for this particular applicationincorporated ten FloMax ® FM-10 air atomizing nozzlelances monitored and controlled by a Model 2250AutoJet Spray Controller using closed loop temperaturecontrol. Based on input from multiple temperaturesensors, the system automatically adjusts the liquidflow to maintain the desired outlet gas temperature.Independent flow monitoring of each nozzle’slance water and air supply ensures peak performancewithout interruption.Marking Defects in Steel Qualityduring Quality ChecksSome mills utilize a quality control system that markssteel defects with color. These systems often use adigital signal to convey that a defect has been identified.AutoJet Spray Systems can be integrated with thequality system to mark the defect with a thin strip of acolored solution to prevent sub-standard product frombeing shipped.Dispensing Oil at Varying Flow Rates Using aZoned Spray HeaderIf you need to apply different oil products at variableflow rates, a zoned header system may be just whatyou need to ensure precise application of the proper oil.An AutoJet Spray Controller can monitor and controlthe spray process, maintaining the proper flow rate asline speed varies and ensuring that various strip widthsare accurately coated.Photos courtesy of United States Steel Corporation.46

DescaleJet ®Descaling/Hot Strip MillLower Costs and Improve Steel Quality inCSP mills with AA214 DescaleJetA new design coupled with a harder, finer grade of carbide allows our AA214DescaleJet nozzle to offer better wear resistance and longer intervals betweenmaintenance than ever before. The more robust carbide insert is now presseddirectly into the body. Plus, fluid passages have been re-engineered to reduceturbulence, improve nozzle durability and increase impact by producing a thinnerspray.The AA214 DescaleJet nozzle is more compact than standard descaling nozzlesso nozzles can be installed closer together allowing for less coverage per nozzle.Less coverage produces greater impact and a more effective, uniform spray is produced.Better surface cleaning is the result.AA214 DescaleJet nozzles also offer exceptionally low flow rates – 4.8 to 18.1 gpm(18.2 to 68.5 l/min) at 2000 psi (138 bar) and a maximum operating pressure of5800 psi (400 bar). Lower water consumption means lower costs and a savings thatgoes right to the bottom line.Specifications:• Spray angles: 18°, 25°, 42° and 40°• Materials: Stainless steel with tungsten carbide orifice insert• Rigid weld configuration fits any pipe assembly47

48Descaling/Hot Strip MillDimensions – AA214 DescaleJetDescaleJet ®

DescaleJet ®Descaling/Hot Strip MillPerformance — DescaleJet 214*At the stated pressure in barTip Sub-Asb. No. 38801-2504E-SSTC4004E-SSTC2505E-SSTC4005E-SSTC2506E-SSTC4006E-SSTC2507E-SSTC4007E-SSTC2508E-SSTC4008E-SSTC2509E-SSTC4009E-SSTC2510E-SSTC4010E-SSTC2515E-SSTC4015E-SSTCNozzle Orifice InsertNo.TC2504ETC4004ETC2505ETC4005ETC2506ETC4006ETC2507ETC4007ETC2508ETC4008ETC2509ETC4009ETC2510ETC4010ETC2515ETC4015EEquiv. Orifice Dia.Capacity (Liters per minute)mm 200 250 300 350 4001.3 13.0 14.5 15.9 17.2 18.41.4 16.2 18.1 19.9 21 231.6 19.5 22 24 26 281.7 23 25 28 30 321.8 26 29 32 34 371.9 29 33 36 39 412.0 32 36 40 43 462.5 49 54 60 64 69CapacitySpray Height “H” (mm)“W” - Coverage for Various Spray Angle Series (mm)#25--E#40--E50 37 5275 55 75100 73 101150 108 150FOR ACTUAL INSTALLATION, OVER-LAPPING OF ADJACENT SPRAYPATTERNS IS SUGGESTED.Ordering InfoAA214 DescaleJet with Weld BodyAA214 DescaleJet with AdapterAA214 – 1 – L + TC2504EAA214 – 2 – R + TC4005ENozzle Cap/Strainer Offset OrificeNumber 1 = Cap L = Left Insert Number2 = Strainer R = RightNozzle Cap/Strainer Offset SprayNumber 1 = Cap L = Left Tip2 = Strainer R = Right49

Descaling/Hot Strip MillDescaleJet ®Standard DescaleJet Nozzles: Idealfor Descaling Ingots, Slabs, Bars,Plates and MoreSeveral basic models of self-aligning DescaleJet nozzles areavailable for use in hot strip mills where spray heights of 6” to12” (152 mm to 305 mm) are required. Used after the roughingstands, these nozzles deliver a flat spray pattern with up to 50%more impact than conventional nozzles. An internal vane stabilizesthe spray and enables higher impact to be achieved.Basic DescaleJet nozzles feature self-aligning spray tips. A stainlesssteel body and spray tip holder provides heavy outer protectionfrom splash-back wear and flying debris. All working parts, includingalignment elements, are positioned internally for maximum protection.Specifications:• Capacities: 15 to 52 gpm (56.8 to 196.8 l/min) at 2000 psi (138 bar)• Materials: Stainless steel with hardened stainless steel or tungstencarbide inserts• Spray angles: 15°, 18°, 25°, 32° and 40°• 1” inlet connectionsDimensions – 26180 DescaleJetOrdering Info26180 DescaleJet Spray Nozzle26180 – 1 + TC2530ENozzle Cap OrificeNumber 1 = Cap Insert Number2 = Strainer50

DescaleJet ®Descaling/Hot Strip MillDimensions – 26190 DescaleJetOrdering Info26190 DescaleJet Spray Nozzle26190 – 1 + TC2530ENozzle Cap OrificeNumber 1 = Cap Insert Number2 = StrainerDimensions – 218 DescaleJetOrdering Info218 DescaleJet Spray NozzleAA218C – 1 + TC2530ENozzle Cap OrificeNumber 1 = Cap Insert Number2 = Strainer51

Descaling/Hot Strip MillDescaleJet ®Performance – 26180, 26190, 218 DescaleJet Nozzles*At the stated pressure in bar.Nozzle OrificeInsert No.Equiv.Orifice Dia.(mm)Capacity (Liters per minute)*40 50 60 80 100 120 140 150 160TC1510E* 2.0 14.4 16.1 17.6 20 23 25 27 28 29TC1520E* 2.8 29 32 35 41 46 50 54 56 58TC1530E 3.5 43 48 53 61 68 75 81 84 86TC1540E 4.0 58 64 71 82 91 100 108 112 115TC1550E 4.4 72 81 88 102 114 125 135 140 144TC1560E 4.8 86 97 106 122 137 150 162 167 173TC1570E 5.2 101 113 124 143 160 175 189 195 202TC1808E* 1.8 11.5 12.9 14.1 16.3 18.2 20 22 22.5 23TC1812E* 2.1 17.3 19.3 21 24 27 30 32 33 35TC1820E* 2.8 29 32 35 41 46 50 54 56 58TC1830E 3.5 43 48 53 61 68 75 81 84 86TC1840E 4.0 58 64 71 82 91 100 108 112 115TC1850E 4.4 72 81 88 102 114 125 135 140 144TC1855E* 4.6 79 89 97 112 125 137 148 154 159TC1860E 4.8 86 97 106 122 137 150 162 167 173TC2508E* 1.8 11.5 12.9 14.1 16.3 18.2 20 22 22.5 23TC2510E* 2.0 14.4 16.1 17.6 20 23 25 27 28 29TC2512E* 2.1 17.3 19.3 21 24 27 30 32 33 35TC2515E* 2.4 22 24 26 31 34 37 40 42 43TC2520E* 2.8 29 32 35 41 46 50 54 56 58TC2525E 3.2 36 40 44 51 57 62 67 70 72TC2530E 3.5 43 48 53 61 68 75 81 84 86TC2535E* 3.6 50 56 62 71 80 87 94 98 101TC2540E 4.0 58 64 71 82 91 100 108 112 115TC2550E 4.4 72 81 88 102 114 125 135 140 144TC2555E* 4.6 79 89 97 112 125 137 148 154 159TC2560E 4.8 86 97 106 122 137 150 162 167 173TC2570E 5.2 101 113 124 143 160 175 189 195 202TC3208E* 1.8 11.5 12.9 14.1 16.3 18.2 20 22 22.5 23TC3210E* 2.0 14.4 16.1 17.6 20 23 25 27 28 29TC3212E* 2.1 17.3 19.3 21 24 27 30 32 33 35TC3215E* 2.4 22 24 26 31 34 37 40 42 43TC3220E* 2.8 29 32 35 41 46 50 54 56 58TC3230E 3.5 43 48 53 61 68 75 81 84 86TC3240E 4.0 58 64 71 82 91 100 108 112 115TC3250E 4.4 72 81 88 102 114 125 135 140 144TC3255E* 4.6 79 89 97 112 125 137 148 154 159TC3260E 4.8 86 97 106 122 137 150 162 167 173TC3270E 5.2 101 113 124 143 160 175 189 195 202TC4030E 3.5 43 48 53 61 68 75 81 84 86TC4040E 4.0 58 64 71 82 91 100 108 112 115TC4050E 4.4 72 81 88 102 114 125 135 140 144TC4060E 4.8 86 97 106 122 137 150 162 167 173*Not used with AA218C, AA218AC, 26180-1, 26180-2, 26190-1 and 26190-2 DescaleJet nozzles.52

DescaleJet ®Descaling/Hot Strip MillSpray Angle — 26180, 26190, 218 DescaleJet NozzlesSpray Height “H” (mm)“W” - Coverage for Various Spray Angle Series (mm)#15—E #18—E #25—E #32—E #40—E205 85 90 125 150 180230 90 100 145 165 195255 95 110 155 180 215280 105 120 170 195 235305 110 130 180 210 255330 120 140 190 220 265355 125 150 200 240 285405 145 170 220 265 315460 155 195 245 290 345510 165 215 260 305 370560 175 235 275 320 380610 180 260 285 325 38553

Strip Wash-Off/Hot Strip MillHigh Impact Cooling and Rinsing Solutions:FlatJet and FloodJet Spray NozzlesFlatJet and FloodJet spray nozzles are used in a variety of steel mill applicationstypically in areas where high impact sprays are needed and/or clogging is a concern.For example, FlatJet and FloodJet nozzles are often used to blow loose scaleacross and off the strip. Another common use is in quenching applications wherethe water source may be filled with contaminants.FlatJet nozzles use a deflector plane to produce a high impact flat spray patternwith narrow spray angles. These nozzles feature a one-piece design and a large,unobstructed flow passage to minimize clogging.FloodJet spray nozzles feature a wide-angle flat spray pattern with medium impact.Similar to FlatJet nozzles, they produce a uniform spray distribution of mediumsizeddrops and have large, unobstructed flow passages to minimize clogging.Suitable for use with liquid or air and steam, the nozzle’s deflector surface providesdependable, accurate control of deflection and spray angle.FlatJet nozzle specifications• Capacities: 0.50 to 20 gpm at 40 psi (2.0 to 75.7 l/min at 3 bar)• Materials: Brass, mild steel, 303 stainless steel, 316 stainless steel• Spray angles: 50°, 40°, 35°, 25° and 15°• 1/8” to 3/4” inlet connectionsFloodJet nozzle specifications• Capacities – Liquid: 0.05 to 90 gpm at 40 psi (0.2 to 340.7 l/min at 3 bar)• Capacities – Air: 0.35 to 25.4 SCFM at 40 psi (10.5 to 760 l/min at 3 bar).Steam: 0.78 to 56.9 lb/hr at 40 psi (0.37 to 27 kg/hr at 3 bar)• 1/8” to 1” inlet connections• Materials: Brass, 303 stainless steel, 316 stainless steel and polyvinyl chloride54

Strip Wash-Off/Hot Strip MillPerformance — FlatJet Nozzles*At the stated pressure in bar.SprayAngleDegreeat 3 bar504035Nozzle Inlet Conn. NPT orBSPT (in.)CapacitySizeEquiv.OrificeDia. (mm)Capacity (Liters per minute)*55Spray AngleDegree*1/8 1/4 3/8 1/2 3/4 1 2 3 4 5 6 7 10 1 3 7ALength(mm)DimensionsBDeflectionAngleDegreeC BarSize (mmsq.)● 05 1.3 1.2 1.6 2.0 2.3 2.6 2.8 3.1 3.7 33 50 60 31 60 15.9 .03● 10 1.9 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 34 50 60 31 60 15.9 .03● ● 25 3.0 5.7 8.1 9.9 11.4 12.7 14.0 15.1 18.0 42 50 59 41.5 42 19.1 .09● ● 40 3.8 9.1 12.9 15.8 18.2 20 22 24 29 39 50 60 47 45 19.1 .09● 60 4.6 13.7 19.3 24 27 31 33 36 43 42 50 53 55 37 25.4 .14● 100 5.9 23 32 39 46 51 56 60 72 43 50 55 72 40 31.8 .33● 125 6.6 28 40 49 57 64 70 75 90 38 50 59 72 38 31.8 .31● 160 7.5 36 52 63 73 82 89 96 115 44 50 55 72 37 31.8 .31● 200 8.4 46 64 79 91 102 112 121 144 46 50 53 72 32 31.8 .31● 40 3.8 9.1 12.9 15.8 18.2 20 22 24 29 31 40 50 60.5 35 22.2 .14● 50 4.2 11.4 16.1 19.7 23 25 28 30 36 31 40 49 63.5 33 25.4 .20● 60 4.6 13.7 19.3 24 27 31 33 36 43 32 40 49 72 33 25.4 .23● 70 5 16.0 23 28 32 36 39 42 50 32 40 49 75.5 29 25.4 .26● 80 5.3 18.2 26 32 36 41 45 48 58 32 40 48 77 26 25.4 .26● 90 5.6 21 29 36 41 46 50 54 65 34 40 44 77 28 25.4 .23● 100 5.9 23 32 39 46 51 56 60 72 35 40 44 86.5 28 25.4 .26● 04 1.2 0.91 1.3 1.6 1.8 2.0 2.2 2.4 2.9 20 35 41 23 40 11.1 .01● 10 1.9 2.3 3.2 3.9 4.6 5.1 5.6 6.0 7.2 18 35 39 36.5 36 15.9 .06● ● 20 2.7 4.6 6.4 7.9 9.1 10.2 11.2 12.1 14.4 24 35 40 42 30 19.1 .06● 25 3 5.7 8.1 9.9 11.4 12.7 14.0 15.1 18.0 24 35 39 49 28 19.1 .09● 30 3.3 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 26 35 41 52.5 28 19.1 .09● 40 3.8 9.1 12.9 15.8 18.2 20 22 24 29 28 35 38 58 26 22.2 .11● 50 4.2 11.4 16.1 19.7 23 25 28 30 36 31 35 38 63.5 23 22.2 .14● 60 4.6 13.7 19.3 24 27 31 33 36 43 29 35 39 73 27 25.4 .23● 80 5.3 18.2 26 32 36 41 45 48 58 26 35 40 81 24 25.4 .26● 100 5.9 23 32 39 46 51 56 60 72 26 35 40 89 19 25.4 .26● 160 7.5 36 52 63 73 82 89 96 115 26 35 40 114 23 31.8 .57● 200 8.4 46 64 79 91 102 112 121 144 25 35 40 122 22 31.8 .5725 ● 40 3.8 9.1 12.9 15.8 18.2 20 22 24 29 15 25 34 65 25 19.1 .1115● 10 1.9 2.3 3.2 3.9 4.6 5.1 5.6 6 7.2 — 15 23 47.5 22 15.9 .06● 20 2.7 4.6 6.4 7.9 9.1 10.2 11.2 12.1 14.4 — 15 19 54 19 15.9 .06● 30 3.3 6.8 9.7 11.8 13.7 15.3 16.7 18.1 22 6 15 24 72 25 19.1 .11● 40 3.8 9.1 12.9 15.8 18.2 20 22 24 29 8 15 21 92 18 22.2 .23● 50 4.2 11.4 16.1 19.7 23 25 28 30 36 9 15 20 90.5 15 22.2 .17● 60 4.6 13.7 19.3 24 27 31 33 36 43 10 15 19 125 14 25.4 .34● 80 5.3 18.2 26 32 36 41 45 48 58 11 15 18 130 14 25.4 .34● 100 5.9 23 32 39 46 51 56 60 72 11 15 18 137 14 25.4 .40● 200 8.4 46 64 79 91 102 112 121 144 12 15 18 191 14 31.8 .91NetWeight(kg)

Strip Wash-Off/Hot Strip MillPerformance – FloodJet Nozzles*At the stated pressure in bar.Nozzle Inlet Conn. NPT orBSPT (in.)CapacitySizeEquiv.OrificeDia. (mm)Capacity (Liters per minute)*Spray Angle Degree1/8 1/4 3/8 1/2 3/4 1 0.2 0.3 0.5 0.7 1 1.5 2 3 4 0.5 1.5 4● .25 .43 — — — — .11 .14 .16 .20 .23 — 83 117● .50 .58 — — — — .23 .28 .32 .39 .46 — 89 122● .75 .74 — — — .29 .34 .42 .48 .59 .68 — 106 125● 1 .84 — — — .38 .46 .56 .64 .79 .91 — 103 128● 1.5 1.0 — — .48 .57 .68 .84 .97 1.2 1.4 73 103 125● ● 2 1.2 — — .64 .76 .91 1.1 1.3 1.6 1.8 83 113 129● ● 2.5 1.3 — .62 .81 .95 1.1 1.4 1.6 2.0 2.3 98 122 133● ● 3 1.4 — .75 .97 1.1 1.4 1.7 1.9 2.4 2.7 86 112 126● 4 1.7 — 1.0 1.3 1.5 1.8 2.2 2.6 3.2 3.6 97 123 132● ● 5 1.9 1.0 1.2 1.6 1.9 2.3 2.8 3.2 3.9 4.6 114 128 142● ● 7.5 2.3 1.5 1.9 2.4 2.9 3.4 4.2 4.8 5.9 6.8 101 119 134● ● 10 2.7 2.0 2.5 3.2 3.8 4.6 5.6 6.4 7.9 9.1 115 133 145● ● 12 2.9 2.4 3.0 3.9 4.6 5.5 6.7 7.7 9.5 10.9 128 139 153● ● 15 3.3 3.1 3.7 4.8 5.7 6.8 8.4 9.7 11.8 13.7 98 113 123● ● 18 3.6 3.7 4.5 5.8 6.9 8.2 10.0 11.6 14.2 16.4 106 120 131● ● 20 3.8 4.1 5.0 6.4 7.6 9.1 11.2 12.9 15.8 18.2 110 122 133● 22 3.9 4.5 5.5 7.1 8.4 10.0 12.3 14.2 17.4 20 113 125 136● 24 4.1 4.9 6.0 7.7 9.2 10.9 13.4 15.5 18.9 22 115 131 144● 27 4.4 5.5 6.7 8.7 10.3 12.3 15.1 17.4 21 25 119 135 148● 30 4.6 6.1 7.5 9.7 11.4 13.7 16.7 19.3 24 27 100 110 121● 35 5.0 7.1 8.7 11.3 13.3 16.0 19.5 23 28 32 105 118 128● ● 40 5.3 8.2 10.0 12.9 15.3 18.2 22 26 32 36 111 126 136● 45 5.6 9.2 11.2 14.5 17.2 21 25 29 36 41 115 130 140● 50 5.9 10.2 12.5 16.1 19.1 23 28 32 39 46 117 131 140● 60 6.5 12.2 15.0 19.3 23 27 33 39 47 55 120 134 142● 70 7.0 14.3 17.5 23 27 32 39 45 55 64 123 137 146● 80 7.5 16.3 20 26 31 36 45 52 63 73 127 138 149● 90 8.1 18.3 22 29 34 41 50 58 71 82 120 133 140● 100 8.5 20 25 32 38 46 56 64 79 91 123 136 145● 110 8.9 22 27 35 42 50 61 71 87 100 125 138 148● 120 9.3 24 30 39 46 55 67 77 95 109 129 143 150● 140 10.0 29 35 45 53 64 78 90 111 128 118 127 135● 160 10.7 33 40 52 61 73 89 103 126 146 121 130 137● 180 11.4 37 45 58 69 82 100 116 142 164 124 133 139● 210 12.3 43 52 68 80 96 117 135 166 191 128 139 145● 300 14.8 61 75 97 114 137 167 193 235 275 110 128 135● 450 18.0 92 112 145 172 205 250 290 355 410 118 132 13856

Strip Wash-Off/Hot Strip MillAir & Steam Performance — FloodJet Nozzles*At the stated pressure in bar.Nozzle Inlet Conn.NPT or BSPT (in.)1/8, 1/4, 3/8CapacitySizeEquiv. OrficeDia. (mm)Capacity – for Air (Nl/min)*Capacity – for Steam (kg per hour)*Coverage at 150 mm Distancefrom Nozzle (mm)*0.7 2 4 0.7 1.5 3 3.5 0.7 3.5.50 .58 4.5 8.1 12.0 .16 .23 .37 .41 51 127.75 .74 6.2 11.5 17.3 .23 .33 .53 .60 64 1401 .84 9.6 17.4 26 .34 .49 .80 .90 76 1521.5 1.0 15.3 28 41 .54 .78 1.3 1.5 89 1652 1.2 19.3 35 53 .68 1.0 1.6 1.8 102 1902.5 1.3 27 48 74 .95 1.3 2.1 2.5 102 1903 1.4 31 58 89 1.1 1.7 2.7 3.0 127 2034 1.7 40 71 113 1.4 2.0 3.1 3.9 127 2285 1.9 54 96 144 1.9 2.7 4.5 5.0 152 2677.5 2.3 79 146 220 2.9 4.2 6.8 7.6 152 26710 2.7 110 200 300 3.9 5.7 9.2 10.4 178 27915 3.3 181 330 493 6.5 9.3 15.0 17.1 178 30520 3.8 225 409 615 8.0 11.6 18.8 21 216 36830 4.6 320 586 881 11.6 16.8 27 30 216 394DimensionsNozzle Type (Conn.) Inlet Conn. (in.) Length (in.) Length (mm) Hex. (in.) Hex. (mm) Net Weight (oz.) Net Weight (kg)1/8 1 25.4 7/16 11.1 .5 .0151/4 1-7/32 30.9 9/16 14.3 1 .03K(M)3/8 1-3/4 44.5 11/16 17.5 2 .061/2 2 51 7/8 22.2 4 .11Based on largest/heaviest version of each type.3/4 2-9/16 65.1 1-1/2 38.1 14 .401 3-5/8 92.1 1-7/8 47.6 32 .91Ordering InfoFloodJet Spray Nozzle1/8 K – SS 0.5FlatJet Spray Nozzle3/8 P – SS – 50 60InletConn.NozzleTypeMaterialCodeCapacitySizeInlet Nozzle Material Spray CapacityConn. Type Code Angle Size57

Strip Wash-Off/Hot Strip MillHigh Impact Spot Spraying Solutions:WashJet Spray NozzlesWashJet high-pressure spray nozzles operate at pressures from 300 to 4000 psi(20 to 275 bar) and feature a high impact solid stream (0°) or flat spray patternwith spray angles of 5° to 65°. Ideal for spot cleaning or light descaling of billets,blooms or rounds, WashJet nozzles use an internal guide vane to stabilize liquidturbulence to provide maximum spray integrity and impact.Milled flats parallel to the plane of the spray pattern provide a visual referencefor quick and easy spray alignment. Specialty hardened stainless steel constructionprovides longer wear-life and flow control accuracy. Or, for maximum erosionresistance, specify WashJet nozzles with tungsten carbide orifice inserts.Specifications:• Capacities: .1 to 3 gpm at 40 psi (.39 to 11.8 at 3 bar)• Material – MEG WashJet nozzles: Specialty hardened stainless steel• Material – MEG-SSTC WashJet nozzles: Stainless steel with tungsten carbideorifice inserts• Spray angles: 65°, 50°, 45°, 25°, 15° and 0°• 1/8” to 1/4” inlet connectionsDimensionsNozzle Type (Conn.) Inlet Conn. (in.) Length (in.)Length(mm)Hex.(in.)Hex.(mm)Flats(in.)Flats(mm)Net Weight(oz.)Net Weight(kg)1/8 7/8 22 1/2 12.7 5/16 7.9 .61 .02MEG (M)29/32 flat 23 flat1/49/16 14.3 13/32 10.3 .76 .021-1/64 solid 26 solidBased on largest/heaviest version of each type.Ordering InfoWashJet Spray Nozzle1/4 MEG - 15 04Inlet Nozzle Spray CapacityConn. Type Angle Size58

Strip Wash-Off/Hot Strip MillPerformance – WashJet Spray Nozzles*At the stated pressure in bar.Nozzle Type and Spray Angle Degree1/8 MEG 1/4 MEG 1/4 MEG-SSTCCapacitySizeCapacity (Liters per minute)*00 5 15 25 40 50 65 00 5 15 25 40 50 65 00 5 15 25 40 50 65 20 25 30 35 40 50 60 70 100 150 200● ● ● ● 01 1.0 1.2 1.3 1.4 1.5 1.6 1.8 1.9 2.3 2.8 3.2● 015 1.5 1.7 1.9 2.0 2.2 2.4 2.6 2.9 3.4 4.2 4.8● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 02 2.0 2.3 2.5 2.7 2.9 3.2 3.5 3.8 4.6 5.6 6.4● 025 2.6 2.9 3.1 3.4 3.6 4.1 4.4 4.8 5.7 7.0 8.1● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 03 3.1 3.4 3.7 4.0 4.3 4.8 5.3 5.7 6.8 8.4 9.7● ● ● ● 035 3.6 4.0 4.4 4.7 5.1 5.7 6.2 6.7 8.0 9.8 11.5● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 04 4.1 4.6 5.0 5.4 5.8 6.4 7.1 7.6 9.1 11.2 12.9● ● ● ● ● ● ● ● ● ● ● ● 045 4.6 5.1 5.6 6.1 6.5 7.3 7.9 8.6 10.3 12.6 14.5● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 05 5.1 5.7 6.2 6.7 7.2 8.1 8.8 9.5 11.4 14.0 16.1● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 055 5.6 6.3 6.9 7.4 7.9 8.9 9.7 10.5 12.5 15.4 17.7● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 06 6.1 6.8 7.5 8.1 8.6 9.7 10.6 11.4 13.7 16.7 19.3● ● ● ● ● ● ● ● ● 065 6.6 7.4 8.1 8.8 9.4 10.5 11.5 12.4 14.8 18.1 21● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 07 7.1 8.0 8.7 9.4 10.1 11.3 12.4 13.3 16.0 19.5 23● ● ● ● ● ● ● ● 075 7.6 8.5 9.4 10.1 10.8 12.1 13.2 14.3 17.1 21 24● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 08 8.2 9.1 10.0 10.8 11.5 12.9 14.1 15.3 18.2 22 26● ● ● ● ● ● ● ● 085 8.7 9.7 10.6 11.5 12.3 13.7 15.0 16.2 19.4 24 27● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 09 9.2 10.3 11.2 12.1 13.0 14.5 15.9 17.2 21 25 29● ● ● ● 095 9.7 10.8 11.9 12.8 13.7 15.3 16.8 18.1 22 27 31● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 10 10.2 11.4 12.5 13.5 14.4 16.1 17.7 19.1 23 28 32● ● ● ● ● ● 11 11.2 12.5 13.7 14.8 15.9 17.7 19.4 21 25 31 35● ● ● 115 11.7 13.1 14.4 15.5 16.6 18.5 20 22 26 32 37● ● ● ● ● ● ● ● ● ● 12 12.2 13.7 15.0 16.2 17.3 19.3 21 23 27 33 39● ● ● ● ● 125 12.7 14.2 15.6 16.9 18.0 20 22 24 28 35 40● ● ● ● ● 13 13.3 14.8 16.2 17.5 18.7 21 23 25 30 36 42● ● ● 14 14.3 16.0 17.5 18.9 20 23 25 27 32 39 45● ● ● ● ● ● ● ● ● ● ● ● ● ● 15 15.3 17.1 18.7 20 22 24 26 29 34 42 48● ● ● 16 16.3 18.2 20 22 23 26 28 31 36 45 52● ● ● ● ● 18 18.3 21 22 24 26 29 32 34 41 50 58● ● ● ● ● ● ● ● ● 20 20 23 25 27 29 32 35 38 46 56 64● ● ● ● ● 25 25 28 31 34 36 40 44 48 57 70 81● ● ● ● ● ● 30 31 34 37 40 43 48 53 57 68 84 97● ● ● ● 35 36 40 44 47 50 56 62 67 80 98 113● ● ● ● ● 40 41 46 50 54 58 64 71 76 97 112 129● ● ● ● 50 51 57 62 67 72 81 88 95 114 140 161● ● ● ● 60 61 68 75 81 86 97 106 114 137 167 193● 70 71 80 87 94 101 113 124 133 160 195 225● 80 82 91 100 108 115 129 141 153 182 225 260● 90 92 103 112 121 130 145 159 172 205 250 290● 105 107 120 131 141 151 169 186 200 240 — —59

Run-off Table/Hot Strip MillLaminar FlowNeed Efficient Cooling on Runout Tables?Choose From These Cost-Effective SolutionsOur Laminar Flow Header with VeeJet® spray nozzles produces a rod-like column ofwater that has proven superior to conventional U-tube nozzle cooling. And with operatingpressures as low as 0.9 psi (0.06 bar), laminar cooling uses water more effectively.At these low pressures, less water is used, runout tables can be shortened andcost-savings on piping can result.A long, smooth approach ensures nozzle inlets are always high in the water manifold.Since the entire header doesn’t have to fill or drain to interrupt the flow pattern, headersequencing is much easier and more precise. Also, lag time is greatly reduced.The flow header also features an internal baffle plate that allows for precise flow distributionacross the header without sizing. This simplifies maintenance and replacement.Solid stream VeeJet nozzles are used on the flow header and feature recessed orificesthat remain in adjustment to ensure even flow and minimal maintenance time.Another option is our slit-style laminar flow header. It produces a curtain-like sheet ofwater. The even distribution of water provided by the header ensures consistent sheetcooling and helps minimize cracking and other defects. The slit-design is clog resistantand eliminates the need for maintaining or replacing nozzles. In the event of ashut down, after water has had time to settle, the slit-type laminar flow header can bestarted up again without the worry of plugged nozzles. This eliminates the checkingof nozzles before startup and saves time for mill personnel.Specifications:• Types: Top and bottom• Materials – Headers: Hot rolled steel; Nozzles: brass• Capacities: 300 to 1800 gpm (1136 to 6813 l/min) at pressure less than 4 psi (0.3 bar)60

Spray HeadersLubrication/Strip Wash-Off/Cold Strip MillSpray Headers are Ideal for Cooling,Cleaning and RinsingOur custom-designed spray headers improve product quality, reducewater consumption, eliminate frequent clogging of spray nozzles andminimize production downtime for nozzle maintenance.Common uses for our spray headers include cooling before the coilerto eliminate cracking and extend roll life, cleaning strip steel beforegalvanizing, cooling rolls on a reducing mill and high temperature/high pressure rinsing in a sheet steel pickling operation.Spray headers feature an internal rotating brush assembly that sweepsdebris away from the nozzle without shutting the system down. Duringthe cleaning cycle, the brushes scrub the interior wall of the header aswell as the nozzle orifices. In a matter of seconds, accumulated debrisis removed and discharged through a flush-out valve restoring full liquidflow to the system without contaminating the sprayed surface.There are three styles from which to choose:• Brushless• Manual brush type with handwheel operation• Automatic brush type with motor and timer for completelyautomated operationSpecifications:• Capacities: 0.04 to 53.74 gpm (0.15 to 203.4 l/min)• 1-1/2” to 6” pipe sizes with customer specified lengths• Material: Stainless steel• Spray angles: 60°, 30° and 0°How to order:Contact your local sales engineerwith the following information for ano-obligation quotation.• Pipe size• Material• No. of showers• No. of nozzles per shower• Nozzle orifice size• Spray angle• Operating pressure• Total flow rate per shower• Type of liquid being sprayed• Machine manufacturer and model• Control unit or control unit plusoptional timer61

Lubrication/Strip Wash-Off/Cold Strip MillPerformance — Spray HeadersSpray Headers*At the stated pressure in bar.Spray Angle Degree at4 bar0Solid Stream3060Capacity (Liters per minute)*Nozzle Size Number Orifice Diameter (mm)1.5 3 7 20 5500004 .30 .11 .16 .24 .41 .6800007 .40 .20 .28 .42 .71 1.200009 .50 .25 .36 .54 .92 1.50001 .60 .36 .51 .78 1.3 2.20002 1.0 .64 .91 1.4 2.3 3.90003 1.2 .92 1.3 2.0 3.4 5.60004 1.5 1.2 1.7 2.6 4.4 7.30008 1.9 2.2 3.1 4.8 8.1 13.40012 2.4 3.5 4.9 7.5 12.6 210020 3.2 5.5 7.8 11.9 20 333002 1.0 .64 .91 1.4 2.3 3.93003 1.2 .92 1.3 2.0 3.4 5.63004 1.5 1.2 1.7 2.6 4.4 7.33006 1.8 1.7 2.4 3.7 6.2 10.43008 2.0 2.2 3.1 4.8 8.1 13.43010 2.3 2.8 4.0 6.2 10.5 17.63012 2.5 3.5 4.9 7.5 12.6 213016 2.8 4.5 6.4 9.8 16.5 283020 3.0 5.5 7.8 11.9 20 336002 1.0 .64 .91 1.4 2.3 3.96003 1.2 .92 1.3 2.0 3.4 5.66004 1.5 1.2 1.7 2.6 4.4 7.36006 1.8 1.7 2.4 3.7 6.2 10.46008 2.0 2.2 3.1 4.8 8.1 13.46010 2.3 2.8 4.0 6.2 10.5 17.66012 2.5 3.5 4.9 7.5 12.6 216016 2.8 4.5 6.4 9.8 16.5 286020 3.0 5.5 7.8 11.9 20 336025 3.5 7.1 10.1 15.5 26 446031 4.0 8.8 12.4 18.9 32 536040 4.5 11.2 15.9 24.5 41 696049 5.0 13.7 19.4 30 50 836078 6.0 22 31 47 80 1336099 7.0 28 39 60 101 16760124 8.0 35 49 75 126 21062

Strip Blow-Off/Cold Strip MillFor Fast and Effective Blow-Off and Drying,WindJet Nozzles Are UnsurpassedFor cleaning and drying cut sheets, rolls or other surfaces, our WindJet AirControl Nozzles, WindJet Air Knives and Air Cannons are cost-effective solutions.AA707 and AA727 WindJet nozzles convert a low-pressure volume of compressedair into a targeted, high-velocity, concentrated stream or flat fan of high-impactair. This creates a better pattern than open pipes and/or drilled holes and ensurescost effective, streak-free drying.AA707 WindJet nozzle specifications:• 1/4” male inlet connection• Produces a round spray pattern with minimum noise• Extended ribs protect the recessed orifices from external damage• Ribs provide an air escape should the nozzle be placed against a flat surface• Materials: ABS plastic, aluminum, polyphenylene sulfide (PPS), stainless steeland PVDF• Aluminum and stainless steel versions feature interchangeable caps thatcontrol air usage• Aluminum caps are color-coded for easy identification of flow ratesAA727/Y727 WindJet nozzle specifications:• 1/4” inlet connection• Produces a flat fan spray pattern• Air stream is discharged through 16 precision orifices• Materials: ABS plastic, aluminum, polyphenylene sulfide (PPS) and stainlesssteel• Produces a tightly directed flat spray pattern with minimum noise levels• Extended ribs protect the recessed orifices against external damage• Ribs also provide an air escape should the nozzle be placed against a flatsurface and they accommodate a deep well socket• A convenient mounting hole on the ABS, PPS and stainless steel versionsensures correct positioning on the header or manifold for fixed applications63

Strip Blow-Off/Cold Strip MillPerformance – WindJet NozzlesInlet Conn.NPT orBSPT (in.)1/4 AA7071/4* Model AA707-AL (aluminum) only.Nozzle Type Capacity Size Cap* ColorAA727Y727Capacity (Nl/min)*0.7 2 4 611 green 147 266 442 61215 yellow 181 345 578 81023 red 294 530 889 123711 — 142 246 396 54915 — 193 357 586 81623 — 280 510 852 1198DimensionsBNozzle Type (Conn.)AInletConn.(in.)A (in.)A(mm)B(in.)B(mm)NetWeight(oz.)NetWeight(kg)AA707 (M) 1/4 1-7/8 48 1 25 1.6 .05Ordering InfoWindJet NozzleAA707 — 1/4 — AL — 11Nozzle Inlet Material CapacityType Conn. Code SizeAA727 — 1/4 — RY — 15Nozzle Inlet Material CapacityType Conn. Code SizeY727 – ALAA727 (M) 1/4 3-9/16 91 2 51 2.0 .06NozzleTypeMaterialCodeBAY727 (F) 1/4 3-9/16 91 2 51 2.2 .0664

Strip Blow-Off/Cold Strip MillWindJet Air KnifeIf your application allows nozzle placement close tothe target and the ambient environment is clean, ourWindJet Air knife is ideal for quick and even dryingafter washing or rinsing. The WindJet Air knife featuresa unique protruding leading edge that extends1/8” beyond the air slot along the length of the knife.Because of this pronounced edge, the flow of air isdirected out of the knife in a straight stream. This leadsto a stream that retains its integrity in a more controlledmanner.The extended edge also improves the air entrainmentaround the Air Knife body. The WindJet Air Knifeoperates on the principles of the Coanda effect andair entrainment to provide a steady, consistent, highvolumestream of air. The longer edge of the Air Knifetakes advantage of the Coanda effect, which inducesthe supplied air to attach itself to the surface of theknife. The integrity of the air stream is maintainedfurther downstream and a condition conducive to theentraining of ambient air is present, increasing thetotal volume of air.In addition to producing a uniform, controlled airstream, our leading edge helps application set-up. Theextended edge provides a visual guide as to where theair stream is headed. It literally points out the directionof the flow, so you can accurately position the knife foroptimum performance.Specifications:• Two air slot sizes: 0.04” (1.02 mm) and 0.06” (1.52mm) for a higher flow rate• 3” flanged air inlet with threaded mounting insert• Available in six lengths: 6”, 12”, 18”, 24”, 30” and36” (154, 305, 457, 610, 762, 914 mm)• Standard lengths up to 3’ (91.44 cm); customlengths available• Materials: Corrosion-resistant anodized aluminumor stainless steel for long life and durabilityOur WindJet Air Knives are powered by electric regenerativeblowers. These blowers offer performancecomparable to more costly multi-stage or positivedisplacement blowers and operate trouble-free withminimal maintenance. Be sure to request more informationabout our complete WindJet Air knife DryingPackages.Air CannonThe 55155 Air Cannon deliversa high-velocity air stream intoholes and crevices of irregularlyshaped parts, perfect forbeam blanks or extruded sections.The air cannon can alsobe used for blowing out orcleaning areas needing highair concentration, like in tubingapplications.Specifications:• Materials: Anodized aluminum or 316 stainless steel• Three orifice sizes – 1/2”, 3/4” or 1” (12.7, 19.1 or25.4 mm) diameter• Built-in mounting spacer for easy repositioning• Available separately or as part of an Air Knife dryingpackageDimensions — WindJet Air KnifePart NumberKnife Length(mm)Air Slot(mm)Material50750-06-040 154 1.02 Aluminum50750-06-060 154 1.52 Aluminum50750-12-040 305 1.02 Aluminum50750-12-060 305 1.52 Aluminum50750-18-040 457 1.02 Aluminum50750-18-060 457 1.52 Aluminum50750-24-040 610 1.02 Aluminum50750-24-060 610 1.52 Aluminum50750-30-040 762 1.02 Aluminum50750-30-060 762 1.52 Aluminum50750-36-040 914 1.02 Aluminum50750-36-060 914 1.52 Aluminum50700-06-040 154 1.02 Stainless Steel50700-12-040 305 1.02 Stainless Steel50700-18-040 457 1.02 Stainless Steel50700-24-040 610 1.02 Stainless Steel50700-30-040 762 1.02 Stainless Steel50700-36-040 914 1.02 Stainless Steel65

Spangling/Cold Strip MillAir Atomizing Nozzles/Spray ControlHundreds of Air Atomizing Options forDozens of Cold Mill OperationsAir atomizing nozzles are among the most versatile of spray nozzle types withmany diverse uses in mills. Zinc dip, galvanizing, soft quenching and oiling arejust a few of the more common applications. Our line of air atomizing nozzlesis extensive with a wide choice of air and liquid inlet locations, built-in strainersand check valves and multiple spray assemblies. Whether it be an applicationwhere drop size control is critical as in the galvanizing line or where rapidquenching is the goal, Spraying Systems Co. offers a wide variety of productswith different operating characteristics. Plus, we offer a wide variety of materials,spray angles and flow rates. Various mounting options are also available.Optimize the Performance of Your AutomaticSpray Nozzles with Integrated Spray ControlPowered by SprayLogic ® firmware and software, AutoJet ®Spray Controllers accurately monitor and precisely adjust sprayvariables. Our controllers can monitor and control multiplespray nozzles or manifolds and include eight built-in regulationmodes for open-loop or closed-loop spray control.Adding an AutoJet Spray Controller can improve the performanceand efficiency of air atomizing nozzles in a variety ofways:• Accurately control liquid, atomizing air and fan pressures forproper drop size, flow rate and spray angle• Increase cycle speed for automatic spray nozzles andcontrol spray timing more precisely• Easily program system setpoint parameters• Use Pulse Width Modulation to improve the efficiency ofelectric spray nozzles• Notify operators or shut down on specified faults• Assist with troubleshooting spray system problems• Integrate spray control withexisting mill control systems66

Air Atomizing NozzlesSpangling/Cold Strip MillVariable Spray Air Atomizing OptionsAllow Fine-Tuning of Spray PerformanceOur VAU and VMAU Air Atomizing nozzles allow you to adjust the atomizing air, fanair and liquid flow independently. For example, you can reduce the atomizing air toproduce a larger drop size. Or, you can adjust the fan air line to regulate the spraypattern and coverage without affecting the drop size or flow rate. Independent controlof the liquid flow also allows you to achieve various distribution patterns withthe use of just one nozzle. An additional inlet/outlet port allows for liquid recirculationthat effectively maintains the flow of viscous liquids such as oils.The VMAU allows for a slightly finer adjustment of the spray for applications requiringhigh precision. It also features a modular design approach for maximum flexibility.Other unique features of the VMAU include:• O-ring sealed air cap on the fluid tip for positive alignment and sealing• Patent-pending modular body and threadless fluid tip design• Available with anti-bearding set-ups• Use of a baffling system for supplying the atomizing and fan air. This system distributesboth the fan and atomizing air equally, providing a more uniform spraypattern.Current VAU customers can easily change to the VMAU since the centerline distanceand mounting thread is the same on both nozzles.VAU nozzles are available with seven different spray set-ups with flows rangingfrom 0.74 to 47 gph (2.8 to 179 l/h). For complete performance data, request datasheets 37459-V67B, 37459-V67A, 37459-V67, 37459-V113A, 37459-V113, 37459-128and 37459-V152.VMAU nozzles can utilize any of eight different spray set-ups that provide flow ratesranging from 0.74 to 73 gph (2.8 to 276 l/h). The following chart provides liquidcapacity data for each of the available set-ups. Refer to the data sheets listed foradditional details and spray performance data.Performance – VMAU Nozzles*At the stated pressure in bar.Liquid Capacity (Liters per hour)*Spray Set-up NumberData Sheet Number0.2 1.4SUVM67A-SS 2.8 7.3 52530-001SUVM67B-SS 4.2 11.1 52530-002SUVM67-SS 8.1 21 52530-003SUVM113A-SS 13.6 35 52530-004SUVM113-SS 18.4 48 52530-005SUVM128-SS 40.8 106 52530-006SUVM152-SS 72 189 52530-007SUVM189-SS 106 276 52530-008Ordering InfoVMAU Air Atomizing Nozzle1/4VMAU – 316SSSUVM113A – 316SSModel #MaterialCodeSpray Set-upMaterialCodeNote: body, actuator and spray set-up must be ordered separately.67

Spangling/Cold Strip MillAir Atomizing NozzlesStandard Air Atomizing NozzlesOur J Series of air atomizing nozzles include:Low-Capacity Series. Our 1/8J and 1/4J models range in capacity from0.13 to 72 gph (0.49 to 280 l/h).Medium-Capacity Series. Our 1/2J models range in capacity from4.1 to 306 gph (15.5 to 1158 l/h).High-Capacity Series. Our 1J models range in capacity from 24 to 1740 gph(91 to 6586 l/h).These models are designed to operate at air pressures ranging from 10 to 60 psi(0.7 to 4.0 bar) and can be specified with pressure or siphon/gravity liquid-fed sprayset-ups. They are available in an array of body styles and with a variety of options.Material choices include nickel-plated brass, 303 stainless steel, 316 stainless steelalong with other machineable materials. All J Series nozzles are available in dripfreeversions.Detailed information on the options and performance of the air atomizing nozzlesmost commonly used in steel mills can be found in our Industrial Spray ProductsCatalog or by contacting your local sales representative.JSingle Air Line• The J basic nozzle assembly features air and liquidinlets in opposite positions with an end plug. 1/8”and 1/4” inlet connections are available.• The 6218-1/4JAU features a single air line used bothfor spray atomization and for operation of the aircylinder. The single air line is regulated at the desired“on/off” cycle time causing simultaneous flow ofatomizing air and liquid. The nozzle operates up to180 cycles per minute and requires a minimum airpressure of 30 psi (2 bar).Standard1/4 JAUH• The 1/4JAU features 1/4” NPT (F) air and liquid inletsand 1/8” NPT (F) control valve air inlets.• The 1/4JAUH is a compact air actuated automaticspray gun. It can be used with any UniJet® spray tipto provide precise automated control of intermittentspraying.68

Air Atomizing NozzlesSpangling/Cold Strip Mill10535-1/4J, 10536-1/2J,10537-1J24AUA• The J Series Air Atomizing nozzles mix air and liquidsupplied at line pressures up to 125 psi (9 bar) toproduce fine atomization. The self-contained air cylinderprovides controlled “on/off” operation at anydesired frequency up to 180 cycles per minute. The JSeries features a spray nozzle body assembly that iscompletely separate from the air cylinder assemblyfor minimal maintenance and fast, easy cleaning ofthe nozzle. The TEFLON ® packings and gaskets in thenozzle withstand continuous use at temperatures upto 400°F (205°C) and the air cylinder packing is recommendedfor temperatures up to 150°F (65°C).Available with 1/4”. 1/2” and 1” inlet connections.22AUH• A 1/2” (12.7 mm) diameter mounting hole and lockingscrew allows quick installation and positioningof the 22AUH Air Atomizing nozzle on a mountingbar. Constructed of brass with nickel-plated externalsurfaces, the 22AUH also features a TEFLON® valveseat and packings and stainless steel valve stem.A variety of spray tips are available in flat, hollowcone and full cone spray patterns. The 22AUH is alsoavailable with an inlet body and cap assembly ofstainless steel.Cycles/min: 180Pressure: 600 psi (40 bar)Capacity: 2 gpm (7.6 l/min)• 24AUA Air Atomizing nozzles feature a 1/2”(12.7 mm) diameter mounting hole and lockingscrew for quick installation and easy positioning ona mounting bar. The shut-off needle and valve seatare available in tungsten carbide or stainless steel.The valve seat is located directly behind the spray tipfor drip-free shut off. A rear knob locks the shut-offneedle in place to prevent accidental discharge whilechanging spray tips. The liquid inlet connection isavailable in the standard down position or one ofseven other positions in intervals of 45°.Cycles/min: 180Pressure: 4000 psi (280 bar)Capacity: 0.6 gpm (2.3 l/min)24AUA-20190• Offering similar features to the standard 24AUA,this version has an aluminum support body andend cap for a total nozzle weight of 1.25 lbs (0.6 kg).Operating at liquid pressures up to 3000 psi (210bar), the 24AUA-20190 requires a minimum air pressureof 42 psi (3 bar) for the air cylinder.Cycles/min: 180Pressure: 3000 psi (210 bar)Capacity: 0.6 gpm (2.3 l/min)69

Spangling/Cold Strip MillAir Atomizing NozzlesPerformance – Air Atomizing Round Spray NozzlesSpraySet-upNo.SU11SU12ASU12SU22BSU22SU42SpraySet-upConsistsof Fluidand AirCapCombinationFluid Cap2050+Air Cap67147Fluid Cap2050+Air Cap73160Fluid Cap2850+Air Cap73160Fluid Cap40100+Air Cap1401110Fluid Cap60100+Air Cap1401110Fluid Cap100150+Air Cap1891125AirPress.(bar)Liquid Capacity (liters per hour) and Air Capacity (liters per minute)Liquid Pressure (bar)0.7 1.5 2 3 4l/hrAir (l/min)AirPress.(bar)l/hrAir (l/min)AirPress.(bar)l/hrAir (l/min)AirPress.(bar)l/hrAir (l/min)AirPress.(bar).70 2.5 15.6 1.1 6.4 11.9 1.4 6.4 13.9 2.7 6.2 23 3.5 7.8 28l/hrAir (l/min)Air(bar)Liquid(bar)Spray DimensionsSprayAngleDegreeA.85 1.8 19.0 1.4 5.0 15.0 1.7 5.5 16.7 2.8 5.7 25 3.7 7.3 29 .85 .70 13 30 2.71.0 1.4 22 1.7 4.1 18.7 2.0 4.5 19.8 3.0 5.2 27 3.9 6.4 33 1.7 1.5 13 33 3.0— — — 1.8 3.4 20 2.2 3.4 24 3.1 4.7 29 4.2 5.5 38 2.5 2.0 13 36 3.4— — — 2.0 3.0 23 2.4 3.0 26 3.2 4.3 31 4.5 4.5 43 3.1 3.0 14 39 3.8— — — 2.1 2.6 25 2.5 2.5 28 3.4 3.9 33 4.6 4.1 45 4.5 4.0 15 44 4.4— — — 2.2 2.0 27 2.7 2.3 31 3.7 3.0 38 4.8 3.7 47.70 2.5 18.7 1.4 5.7 27 1.7 6.7 29 2.2 9.2 34 2.8 11.9 39.85 2.0 22 1.5 5.2 29 1.8 6.4 31 2.5 8.2 39 3.1 11.0 43 .85 .70 12 43 3.71.0 1.6 26 1.7 4.8 32 2.0 5.9 34 2.8 7.2 44 3.4 10.1 47 1.5 1.5 13 46 4.0— — — 1.8 4.3 35 2.1 5.2 37 3.0 6.7 47 3.7 9.2 52 2.4 2.0 13 48 4.3— — — 2.0 3.9 37 2.2 4.8 40 3.1 6.3 49 3.9 8.4 58 3.0 3.0 13 51 4.6— — — 2.1 3.4 40 2.4 4.3 43 3.2 5.9 52 4.2 7.6 62 3.9 4.0 15 56 5.2— — — — — — 2.7 3.6 48 3.4 5.5 55 4.5 6.8 68.85 4.8 21 1.7 8.4 31 2.0 10.7 33 2.7 16.5 37 3.4 20 431.1 4.1 27 1.8 7.5 35 2.1 9.8 37 2.8 15.4 38 3.7 18.4 47 1.5 .70 12 48 4.01.4 3.4 33 2.0 7.0 37 2.4 8.2 42 3.1 13.6 43 3.9 16.8 50 2.5 1.5 13 51 4.31.5 3.1 35 2.2 5.7 44 2.7 6.8 48 3.4 11.8 49 4.2 15.2 55 3.0 2.0 13 53 4.61.7 3.0 39 2.5 4.8 49 3.0 5.9 55 3.7 10.4 55 4.5 13.8 60 3.4 3.0 14 56 4.91.8 2.9 41 2.8 4.1 54 3.2 5.0 59 3.9 9.1 61 4.8 12.4 65 4.2 4.0 15 60 5.32.0 2.8 44 3.1 3.6 59 3.5 4.1 65 4.2 7.9 65 4.9 11.8 681.1 13.0 76 2.2 17.8 116 2.8 20 136 3.4 32 149 4.6 37 1931.4 8.9 91 2.5 13.1 130 3.1 16.3 149 3.9 25 170 5.3 29 220 1.7 .70 18 66 4.91.5 7.2 98 2.8 9.5 143 3.4 11.9 163 4.6 15.9 205 5.6 25 235 2.8 1.5 20 76 6.11.7 5.8 105 3.1 7.0 157 3.9 7.0 187 5.3 9.1 240 6.0 21 250 3.9 2.0 20 81 6.71.8 4.7 112 3.4 4.9 171 4.2 4.7 205 5.6 6.8 255 6.3 17.4 270 5.3 3.0 21 91 7.92.0 3.6 119 3.5 4.2 178 4.6 3.0 220 6.0 5.0 275 6.7 14.0 290 6.0 4.0 21 97 9.12.1 2.7 127 — — — — — — 6.3 3.6 290 7.0 11.0 305.85 31 57 1.4 61 69 2.1 53 96 2.7 80 103 3.8 88 1351.0 25 66 1.5 54 76 2.4 41 112 3.0 69 117 4.2 73 156 1.0 .70 17 61 4.91.1 18.5 75 1.7 48 85 2.7 31 127 3.2 59 130 4.6 61 176 1.8 1.5 18 69 5.81.3 12.9 85 1.8 41 93 2.8 26 136 3.5 49 146 4.9 48 196 2.8 2.0 20 76 6.7— — — 2.0 35 102 3.0 22 144 3.7 44 154 5.3 39 215 3.5 3.0 20 79 7.0— — — 2.1 30 110 — — — 3.8 37 161 5.6 31 240 4.9 4.0 21 91 8.5— — — 2.2 25 119 — — — 3.9 35 170 6.0 23 2601.0 44 86 1.4 125 79 2.0 123 108 2.2 199 88 3.0 250 991.1 32 102 1.5 106 91 2.1 108 119 2.5 174 110 3.2 225 120 1.0 .70 19 89 6.1— — — 1.7 87 105 2.2 95 130 2.8 146 133 3.5 205 141 1.7 1.5 20 99 7.0— — — 1.8 70 118 2.4 79 143 3.1 121 154 3.8 182 163 2.4 2.0 21 104 7.6— — — 2.0 55 130 2.5 64 155 3.2 108 166 4.1 159 184 3.1 3.0 21 107 7.9— — — — — — 2.7 52 166 3.4 95 176 4.6 121 225 3.8 4.0 22 117 9.1— — — — — — 2.8 42 178 3.5 84 187 4.9 93 255B(cm)D(cm)70

Air Atomizing NozzlesSpangling/Cold Strip MillPerformance – Air Atomizing Wide-Angle Round Spray NozzlesWIDE ANGLE ROUNDSPRAY PATTERNLiquid Capacity (liters per hour) and Air Capacity (liters per minute)Spray SetupNo.SU16SU26BSU26SU29SU30SU46Spray Set-upConsists ofFluid andAir CapCombinationFluid Cap2050+Air Cap67-6-20-70°Fluid Cap40100+Air Cap140-6-37-70°Fluid Cap60100+Air Cap140-6-37-70°Fluid Cap60100+Air Cap140-6-52-70°Fluid Cap40100+Air Cap120-6-35-60°Fluid Cap100150+Air Cap189-6-62-70°AirPress.(bar)Liquid Pressure (bar)0.7 1.5 2 3 4l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar).60 5.3 10.2 1.1 8.1 13.3 1.5 8.1 16.4 2.4 8.9 22 3.1 10.5 24l/hr.Airl/minAir(bar)Liquid(bar)Spray Dimensions.70 4.3 12.2 1.3 7.0 15.0 1.8 6.6 21 2.7 8.1 26 3.4 9.7 28 .70 .70 14 18 23 1.5.85 3.0 14.2 1.4 6.4 17.0 2.1 4.9 25 3.0 6.4 30 3.9 7.8 36 1.4 1.5 15 19 24 1.81.0 1.7 17.0 1.5 5.5 19.0 2.4 3.2 29 3.2 4.9 34 4.2 6.1 42 1.8 2.0 16 20 25 2.1— — — 1.7 4.5 22 — — — 3.4 4.2 37 4.6 4.4 47 3.0 3.0 16 20 26 2.7— — — 1.8 3.5 24 — — — 3.5 3.4 40 4.9 2.8 54 3.9 4.0 19 23 30 4.0.85 7.0 50 1.7 13.2 68 2.0 18.5 68 2.8 25 84 3.7 31 961.0 2.1 62 1.8 9.8 79 2.1 15.1 76 3.0 22 92 3.8 28 105 .85 .70 18 24 31 1.8— — — — — — 2.2 11.7 85 3.1 18.5 101 3.9 26 113 1.7 1.5 19 25 33 2.4— — — — — — — — — 3.2 15.1 109 4.1 23 122 2.1 2.0 19 25 33 3.2— — — — — — — — — 3.4 12.1 119 4.2 20 130 3.2 3.0 20 26 34 4.1— — — — — — — — — 3.5 9.1 130 4.6 13.6 153 4.1 4.0 21 28 37 5.9— — — — — — — — — 3.7 6.1 142 4.9 6.8 183.70 24 32 1.4 43 37 2.1 33 66 2.8 52 65 3.7 63 68.85 13.6 44 1.5 35 49 2.2 26 78 3.0 46 76 3.8 58 79 .85 .70 19 25 36 2.11.0 7.6 57 1.7 28 61 2.4 18.9 89 3.1 39 87 3.9 52 101 1.5 1.5 20 27 37 3.2— — — 1.8 21 71 2.5 11.7 100 3.2 33 99 4.2 41 111 2.4 2.0 20 27 37 4.1— — — — — — — — — 3.4 26 110 4.6 27 138 3.2 3.0 20 28 38 5.0— — — — — — — — — 3.5 19.5 122 4.9 15.9 166 3.9 4.0 20 28 39 6.8— — — — — — — — — 3.7 13.2 133 - - -1.3 36 85 2.1 57 116 3.1 53 156 4.2 64 197 5.6 74 2451.5 29 102 2.4 51 130 3.2 50 163 4.9 51 230 6.0 68 260 2.0 .70 20 25 33 5.51.8 23 117 2.7 45 143 3.4 47 170 5.6 40 265 6.3 62 280 3.0 1.5 20 27 34 6.42.0 19.7 125 3.0 39 157 3.5 45 177 6.0 34 285 6.7 56 295 3.9 2.0 22 28 37 8.22.1 16.7 133 3.2 33 170 3.9 38 194 6.3 28 300 7.0 51 315 6.0 3.0 23 29 38 9.12.3 14.0 142 3.5 28 185 4.6 25 230 6.7 22 320 - - - 6.3 4.0 24 32 41 10.42.4 11.4 149 4.2 13.6 220 4.9 18.5 245 7.0 17.8 335 - - -1.1 12.3 40 2.2 16.3 62 2.7 21 69 4.2 19.3 100 5.6 22 1301.3 9.9 45 2.5 12.1 71 3.0 16.3 78 4.6 14.6 113 6.0 17.6 142 1.5 .70 15 19 23 2.71.4 7.9 50 2.8 8.9 79 3.2 12.3 86 4.9 10.8 124 6.3 14.0 152 3.0 1.5 16 20 24 4.61.5 6.1 54 3.0 7.6 83 3.4 10.7 91 5.3 8.1 135 6.7 11.4 163 3.4 2.0 16 20 24 5.51.7 4.9 58 3.1 6.4 87 3.5 9.3 94 5.6 6.2 146 7.0 9.1 174 5.3 3.0 18 22 25 7.31.8 3.9 62 3.2 5.5 91 3.9 6.4 105 6.0 4.9 157 — — — 6.3 4.0 19 24 30 9.42.0 3.1 67 3.4 4.7 95 4.2 4.7 115 6.3 4.0 167 — — —1.7 25 156 3.0 39 230 3.4 50 250 4.6 62 320 6.0 93 3951.8 19.7 167 3.1 33 240 3.5 43 260 4.9 47 345 6.3 77 425 2.0 .70 24 33 46 5.52.0 15.1 178 3.2 27 255 3.7 41 275 5.3 36 375 6.7 62 460 3.2 1.5 25 34 47 6.42.1 11.4 193 3.4 23 265 3.9 27 300 5.6 26 405 7.0 52 495 3.9 2.0 28 37 51 7.32.3 7.6 205 3.5 18.5 280 4.1 23 310 6.0 18.9 435 — — — 5.3 3.0 29 38 53 7.9— — — 3.7 14.8 290 4.2 18.9 320 6.3 13.6 460 — — — 6.3 4.0 33 42 58 9.8— — — — — — 4.4 15.9 335 — — — — — —A(cm)B(cm)C(cm)D(m)71

Spangling/Cold Strip MillAir Atomizing NozzlesPerformance – Air Atomizing Deflected Flat Spray NozzlesSpray SetupNo.SU240ESpray Set-upConsists ofFluid andAir CapCombinationFluid Cap28150+Air Cap189110-75°AirPress.(bar)Liquid Capacity (liters per hour) and Air Capacity (liters per minute)Liquid Pressure (bar)0.7 1.5 2 3 4l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar).40 11.0 45 1.1 14.5 79 1.5 15.7 96 2.1 20 114 2.7 26 133.60 9.5 54 1.3 13.2 86 1.7 14.3 104 2.2 19.2 121 3.2 22 160.70 7.6 65 1.4 11.8 95 1.8 12.9 112 2.7 15.8 146 3.8 17.7 186.80 5.7 77 1.5 10.0 103 2.1 9.8 130 3.1 11.8 173 4.4 13.1 230— — — 1.7 8.7 113 2.2 8.3 142 3.2 10.3 183 4.6 10.2 250l/hr.Airl/minPerformance – Air Atomizing 360˚ Circular Spray NozzlesSpray SetupNo.SU340CSpray SetupConsistsof Fluid andAir CapCombinationFluid Cap60150+Air Cap189-6-62-160HCAirPress.(bar)Liquid Capacity (liters per hour) and Air Capacity (liters per minute)Liquid Pressure (bar)0.7 1.5 2 3 4l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)1.4 15.1 69 2.8 19.5 142 3.5 21 185 4.2 48 210 6.0 45 3401.5 10.6 77 3.0 16.1 153 3.7 17.6 196 4.6 37 240 6.3 37 3751.7 7.6 84 3.1 13.2 165 3.8 14.8 210 4.9 28 275 6.7 30 4051.8 5.7 93 3.2 10.6 177 3.9 12.5 220 5.6 15.5 340 7.0 24 4402.0 4.2 103 3.4 8.3 188 4.2 8.1 245 6.3 7.8 425 — — —l/hr.Airl/min72

Air Atomizing NozzlesSpangling/Cold Strip MillPerformance – Air Atomizing Flat Spray NozzlesLiquid Capacity (liters per hour) and Air Capacity (liters per minute)Spray SetupNo.Spray SetupConsistsof Fluid andAir CapCombinationAirPress.(bar)Liquid Pressure (bar)0.7 1.5 2 3 4l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAir(bar)Liquid(bar)Spray DimensionsA(cm)B(cm)C(cm)D(m)SU13ASU13SUN13SU14Fluid Cap2050+Air Cap73328Fluid Cap2850+Air Cap73328Fluid Cap2850+Air Cap73335Fluid Cap2850+Air Cap73320.70 5.5 24 1.3 9.1 31 2.0 8.6 42 2.7 11.2 52 3.9 12.0 69.85 4.7 27 1.5 7.7 36 2.2 7.5 47 3.0 10.1 56 4.6 9.7 81 1.1 .70 25 36 46 2.61.0 4.1 31 1.8 6.5 42 2.5 6.2 52 3.2 9.1 62 5.3 7.5 93 2.1 1.5 36 48 66 3.01.1 3.5 34 2.1 5.4 47 2.8 5.2 57 3.5 8.1 66 6.0 5.3 104 2.8 2.0 38 53 76 3.21.3 3.0 37 2.4 4.3 52 3.1 4.2 63 4.2 5.4 79 6.3 4.3 110 3.5 3.0 47 61 86 3.41.4 2.5 40 2.7 3.3 57 3.2 3.7 65 4.6 4.2 85 6.7 3.3 116 6.0 4.0 56 74 94 4.01.5 2.0 44 2.8 2.8 60 3.4 3.2 68 4.9 3.1 91 7.0 2.4 122.85 8.2 19.8 1.4 14.4 27 2.1 13.5 36 2.7 19.1 42 4.6 16.1 691.0 6.8 23 1.7 11.9 32 2.4 11.4 42 3.0 17.1 46 4.9 13.8 76 1.1 .70 36 46 71 2.11.1 5.5 27 2.0 9.5 37 2.7 9.2 47 3.2 15.1 52 5.3 11.5 83 2.1 1.5 43 61 81 2.41.3 4.1 30 2.1 8.3 40 3.0 7.1 53 3.5 13.1 57 5.6 9.3 90 3.0 2.0 51 66 89 2.61.4 2.9 34 2.2 7.1 43 3.2 5.0 59 4.2 8.1 72 6.0 7.3 97 3.5 3.0 58 76 97 2.7— — — 2.4 6.1 46 3.4 4.0 63 4.6 5.9 79 6.3 5.6 104 5.6 4.0 58 76 97 3.2— — — 2.5 5.1 49 3.5 3.3 66 4.9 4.0 86 6.7 4.3 1121.0 9.0 25 2.0 10.4 41 2.4 11.6 48 3.1 15.6 56 4.2 17.1 731.1 7.8 30 2.1 9.3 45 2.5 10.4 51 3.2 14.6 59 4.6 15.0 80 1.4 .70 10 13 17 3.01.3 6.6 32 2.2 8.2 48 2.7 9.4 54 3.4 13.7 62 4.9 12.8 87 2.5 1.5 13 15 20 3.71.4 5.2 36 2.5 6.1 55 3.0 7.3 61 3.8 10.8 71 5.3 11.0 94 3.2 2.0 13 17 22 4.01.7 3.1 44 2.8 4.3 62 3.2 5.5 68 4.2 8.5 82 5.6 9.4 103 3.8 3.0 15 22 28 4.22.0 2.0 50 3.1 3.0 69 3.5 4.1 75 4.9 5.2 98 6.3 7.2 119 5.3 4.0 20 25 33 4.82.2 1.1 56 3.4 2.0 75 3.8 2.9 81 6.0 2.3 120 7.0 6.1 1341.3 3.9 30 2.1 7.4 40 3.0 6.1 52 3.9 9.4 60 5.3 10.2 781.4 3.0 33 2.4 5.3 45 3.1 5.3 54 4.2 7.2 67 5.6 8.3 84 1.5 .70 25 33 46 1.81.5 2.3 35 2.5 4.4 47 3.2 4.5 57 4.6 5.3 73 6.0 6.6 89 2.7 1.5 36 51 69 2.01.7 1.8 38 2.7 3.7 50 3.4 3.8 59 4.9 3.8 80 6.3 5.1 98 3.2 2.0 58 74 91 2.01.8 1.3 41 2.8 3.1 52 3.5 3.2 62 — — — — — — 4.2 3.0 61 74 94 2.12.0 .95 44 3.0 2.6 55 3.9 1.8 68 — — — — — — 5.6 4.0 64 76 97 2.3— — — 3.1 2.1 57 — — — — — — — — —73

Spangling/Cold Strip MillAir Atomizing NozzlesPerformance – Air Atomizing Flat Spray NozzlesLiquid Capacity (liters per hour) and Air Capacity (liters per minute)Spray SetupNo.Spray SetupConsistsof Fluid andAir CapCombinationAirPress.(bar)Liquid Pressure (bar)0.7 1.5 2 3 4l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAirPress.(bar)l/hr.Airl/minAir(bar)Liquid(bar)Spray DimensionsA(cm)B(cm)C(cm)D(m)SUN23SU23BSU23SU43Fluid Cap60100+Air Cap125340Fluid Cap40100+Air Cap125328Fluid Cap60100+Air Cap125328Fluid Cap100150+Air Cap1893511.0 17.0 23 2.0 24 44 2.4 28 51 3.4 38 72 3.9 65 751.1 11.0 27 2.1 18.9 50 2.5 23 59 3.5 33 80 4.2 53 89 1.1 .70 10 13 15 2.41.3 7.6 33 2.2 14.4 56 2.7 18.9 66 3.7 28 89 4.6 40 108 2.1 1.5 10 13 17 3.01.4 3.2 40 2.4 10.6 63 2.8 15.1 74 3.8 23 97 4.9 30 127 2.8 2.0 13 17 22 3.4— — — 2.5 7.2 71 3.0 11.7 79 3.9 19.7 105 5.3 21 149 3.7 3.0 15 20 28 3.6— — — — — — — — — 4.2 13.1 120 5.6 13.8 173 4.9 4.0 20 25 35 4.0— — — — — — — — — 4.6 7.2 138 6.3 3.2 2251.1 11.2 54 2.1 18.0 79 2.7 19.6 93 3.5 27 112 4.6 33 1371.3 8.5 60 2.2 15.8 84 2.8 17.3 98 3.7 25 116 4.9 28 149 1.4 .70 15 18 20 3.01.4 6.5 65 2.4 13.6 89 3.0 15.2 103 3.8 23 121 5.3 24 161 2.4 1.5 23 28 33 3.21.5 5.0 71 2.5 11.6 95 3.1 13.2 109 3.9 21 126 5.6 19.7 174 3.0 2.0 25 33 46 3.41.7 3.8 77 — — — 3.2 11.4 114 4.1 18.9 132 6.0 15.7 187 3.7 3.0 30 38 46 3.5— — — — — — — — — 4.2 17.0 137 6.3 12.4 200 5.3 4.0 33 41 48 4.0.85 27 33 1.8 38 55 2.4 39 67 3.2 58 76 4.6 59 1061.0 20 38 2.1 28 66 2.7 30 77 3.5 47 87 5.3 40 132 1.1 .70 18 23 30 3.41.1 15.9 45 2.2 24 71 3.0 24 87 3.8 38 97 5.6 32 145 2.4 1.5 23 30 41 3.51.3 12.5 48 2.4 21 76 3.2 17.8 98 3.9 34 103 6.0 26 158 3.2 2.0 25 33 43 3.71.4 10.2 56 2.5 17.8 82 3.4 15.1 103 4.2 27 113 6.3 20 172 3.9 3.0 30 38 48 3.81.5 7.6 62 2.7 15.1 87 3.5 12.9 109 4.6 20 126 6.7 15.9 185 6.0 4.0 33 41 51 4.4— — — — — — 3.7 10.6 114 4.9 14.8 140 7.0 12.7 1981.0 29 90 1.8 56 117 2.1 100 119 3.0 126 140 4.1 140 1811.1 18.9 108 2.0 40 133 2.2 79 133 3.1 110 151 4.2 125 193 1.0 .70 18 20 25 3.4— — — — — — 2.4 62 147 3.2 95 163 4.6 89 225 1.8 1.5 25 30 43 3.8— — — — — — 2.5 48 162 3.4 78 184 4.9 58 265 2.4 2.0 25 30 46 4.3— — — — — — 2.7 36 177 3.5 62 193 5.3 34 305 3.4 3.0 33 41 53 4.6— — — — — — — — — 3.7 48 210 5.6 16.7 340 4.9 4.0 36 43 58 5.2— — — — — — — — — 3.8 37 225 — — —74

Air Atomizing NozzlesSpangling/Cold Strip MillPerformance – Air Atomizing Flat External Mix Spray NozzlesSpray SetupNo.SUE15BSUE18BSUE15ASUE18ASUE15SUE18Spray Set-upConsists ofFluid andAir CapCombinationFluid Cap1650+Air Cap67228-45°Fluid Cap1650+Air Cap62240-60°Fluid Cap2050+Air Cap67228-45°Fluid Cap2050+Air Cap62240-60°Fluid Cap2850+Air Cap67228-45°Fluid Cap2850+Air Cap62240-60°AirPress.(bar)Liquid Capacity (liters per hour) and Air Capacity (liters per minute)Liquid Pressure (bar)0.2 0.3 0.7 1.5 3Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.Air(bar)Liquid(bar)Spray Dimensions.20 25.2 2.8 3.5 26.3 3.5 .70 31.2 5.3 1.4 45.3 7.8 2.8 73.6 11.0 .20 .20 9.0 15.0 23 .90.35 26.3 2.8 .70 31.2 3.5 1.05 39.6 5.3 1.75 53.8 7.8 3.5 85 11.0 1.05 .20 9.0 15.0 23 1.2.70 31.2 2.8 1.05 39.6 3.5 1.4 45.3 5.3 2.1 59.5 7.8 4.2 102 11.0 1.4 .35 10.0 15.0 23 1.21.05 39.6 2.8 1.4 45.3 3.5 1.75 53.8 5.3 2.8 73.6 7.8 4.9 119 11.0 1.4 1.4 11.5 18.0 25 1.51.4 45.3 2.8 1.75 53.8 3.5 2.1 59.4 5.3 3.5 85 7.8 5.3 127.5 11.0 1.75 .70 11.5 15.0 24 1.51.75 53.8 2.8 2.1 59.4 3.5 2.8 73.6 5.3 4.2 102 7.8 5.6 139 11.0 2.8 1.4 13.0 18.0 28 1.82.1 59.4 2.8 2.8 73.6 3.5 3.5 85 5.3 5.6 139 7.8 6.3 159 11.0 4.9 2.8 15.0 18.0 24 2.4.35 22 2.8 .35 22 3.5 .40 25 5.3 .60 28 7.8 .70 34 11.0 .60 .70 23 30 40 1.8.40 25 2.8 .40 25 3.5 .60 28 5.3 .70 34 7.8 1.1 45 11.0 .60 1.5 28 35 46 1.8.50 27.5 2.8 .60 28 3.5 .70 34 5.3 1.1 45 7.8 1.8 62 11.0 1.4 1.5 25 30 41 2.7.60 28 2.8 .70 34 3.5 .85 40 5.3 1.4 54 7.8 2.5 79 11.0 1.1 2.0 28 35 48 2.6.35 26.3 4.5 .70 31.2 5.5 1.05 39.6 8.3 1.75 53.8 12.2 3.15 82 16.6 .35 .20 7.5 14.0 22 1.0.70 31.2 4.5 1.05 39.6 5.5 1.4 45.3 8.3 2.1 59.4 12.2 3.5 85 16.6 1.4 .20 9.0 15.0 22 1.71.05 39.6 4.5 1.4 45.3 5.5 1.75 53.8 8.3 2.8 73.6 12.2 4.2 102 16.6 1.75 .35 10.0 16.5 23 1.81.4 45.3 4.5 1.75 53.8 5.5 2.1 59.4 8.3 3.5 85 12.2 4.9 119 16.6 1.75 1.4 13.0 19.0 29 2.11.75 53.8 4.5 2.1 59.4 5.5 2.8 73.6 8.3 4.2 102 12.2 5.25 127 16.6 2.1 .70 13.0 18.0 25 1.82.1 59.4 4.5 2.8 73.6 5.5 3.5 85 8.3 4.9 119 12.2 6.3 159 16.6 3.5 1.4 13.0 22 30 2.42.8 73.6 4.5 3.5 85 5.5 4.2 102 8.3 6.3 159 12.2 6.7 164 16.6 5.3 2.8 15.0 19.0 25 3.0.35 22 4.5 .35 22 5.5 .60 28 8.3 .70 34 12.2 1.1 45 16.6 1.1 .70 30 38 48 2.1.60 28 4.5 .70 34 5.5 .70 34 8.3 1.4 54 12.2 1.4 54 16.6 .70 1.5 38 46 58 1.8.70 34 4.5 1.1 45 5.5 1.4 54 8.3 2.1 71 12.2 2.1 71 16.6 2.5 1.5 33 40 51 3.01.1 45 4.5 1.4 54 5.5 2.1 71 8.3 2.5 79 12.2 2.5 79 16.6 1.8 2.0 38 46 58 2.7.70 31.2 8.5 1.05 39.6 10.4 1.4 45.3 15.9 2.5 68 23 3.5 85 33 .70 .20 13.0 16.5 25 1.21.05 39.6 8.5 1.4 45.3 10.4 1.75 53.8 15.9 2.8 73.6 23 4.2 102 33 1.75 .20 13.0 16.5 25 1.81.4 45.3 8.5 1.75 53.8 10.4 2.1 59.4 15.9 3.5 85 23 4.9 119 33 2.1 .35 13.0 18.0 24 1.81.75 53.8 8.5 2.1 59.4 10.4 2.8 73.6 15.9 4.2 102 23 5.3 127 33 2.5 1.4 14.0 20 32 1.82.1 59.4 8.5 2.8 73.6 10.4 3.5 85.0 15.9 4.9 119 23 5.6 139 33 2.8 .70 14.0 19.0 30 2.32.8 73.6 8.5 3.5 85 10.4 4.2 102 15.9 5.6 139 23 6.3 159 33 4.2 1.4 14.0 20 36 3.03.5 85 8.5 4.2 102 10.4 4.9 119 15.9 6.3 159 23 7.0 176 33 5.3 2.8 16.5 20 30 4.0.40 25 8.5 .40 25 10.4 .40 25 15.9 .70 34 23 1.4 54 33 .60 .70 35 48 63 1.5.50 27.5 8.5 .60 28 10.4 .60 28 15.9 .85 40 23 1.8 62 33 .70 1.5 38 48 63 1.8.60 28 8.5 .65 31 10.4 .70 34 15.9 1.1 45 23 2.1 71 33 1.4 1.5 43 53 66 2.4.70 34 8.5 .70 34 10.4 .85 40 15.9 1.4 54 23 2.5 79 33 1.8 2.0 41 51 69 2.7A(cm)B(cm)C(cm)D(m)75

Spangling/Cold Strip MillAir Atomizing NozzlesPerformance – Air Atomizing Flat External Mix Spray NozzlesSpray SetupNo.SUE25BSUE28BSUE25ASUE28ASUE28SUE25SUE45BSpray Set-upConsists ofFluid andAir CapCombinationFluid Cap35100+Air Cap134255-45°Fluid Cap35100+Air Cap122281-60°Fluid Cap40100+Air Cap134255-45°Fluid Cap40100+Air Cap122281-60°Fluid Cap60100+Air Cap122281-60°Fluid Cap60100+Air Cap134255-45°Fluid Cap60150+Air Cap200278-45°AirPress.(bar)Liquid Capacity (liters per hour) and Air Capacity (liters per minute)Liquid Pressure (bar)0.2 0.3 0.7 1.5 3Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.Air(bar)Liquid(bar)Spray Dimensions.70 85 13.4 1.0 102 16.4 1.4 116 25 2.5 178 37 3.2 212 52 .70 .20 13.0 19.0 25 1.71.0 102 13.4 1.4 116 16.4 1.8 139 25 2.8 195 37 3.5 232 52 1.8 .20 13.0 19.0 25 2.71.4 116 13.4 1.8 139 16.4 2.1 156 25 3.5 227 37 3.9 255 52 2.1 .35 15.0 19.0 28 3.01.8 139 13.4 2.1 156 16.4 2.5 178 25 4.2 266 37 4.2 275 52 2.5 .70 15.0 22 28 3.52.1 156 13.4 2.8 195 16.4 2.8 195 25 4.9 312 37 4.9 314 52 2.5 1.4 16.5 23 36 3.72.8 195 13.4 3.5 227 16.4 3.5 227 25 5.6 360 37 5.6 360 52 4.2 1.4 16.5 23 37 4.33.5 227 13.4 4.2 266 16.4 4.2 266 25 6.3 411 37 6.3 411 52 4.9 2.8 16.5 22 32 4.9.60 91 13.4 .70 102 16.4 1.4 156 25 2.1 210 37 3.2 285 52 2.1 .70 33 40 56 4.3.70 102 13.4 1.1 130 16.4 2.1 210 25 2.8 260 37 4.2 360 52 2.1 1.5 35 46 58 4.01.1 130 13.4 1.8 184 16.4 2.5 235 25 3.5 310 37 5.3 430 52 4.2 1.5 38 48 64 5.21.4 156 13.4 2.1 210 16.4 2.8 260 25 4.2 360 37 5.6 455 52 3.9 2.0 41 51 69 4.6.70 85 17.6 1.4 116 22 1.8 139 33 2.8 195 48 3.5 232 68 .70 .35 15.0 19.0 27 2.11.0 102 17.6 1.8 139 22 2.1 156 33 3.2 212 48 4.2 275 68 1.8 .70 15.0 19.0 27 3.01.4 116 17.6 2.1 156 22 2.5 178 33 3.5 227 48 4.9 314 68 2.5 1.4 15.0 22 33 3.41.8 139 17.6 2.5 178 22 2.8 195 33 4.2 266 48 5.3 340 68 2.8 1.4 15.0 22 36 3.82.1 156 17.6 2.8 195 22 3.5 227 33 4.9 312 48 5.6 360 68 2.8 1.4 16.5 25 37 4.02.8 195 17.6 3.5 227 22 4.2 266 33 5.6 360 48 6.3 411 68 4.2 2.1 16.5 25 37 4.93.5 227 17.6 4.2 266 22 4.9 312 33 6.3 411 48 6.6 428 68 5.3 2.8 18.0 23 36 5.8.60 91 17.6 .70 102 22 1.1 130 33 2.5 235 48 3.5 310 68 1.8 .70 35 48 64 3.01.1 130 17.6 1.4 156 22 1.8 184 33 3.2 285 48 4.6 380 68 2.5 1.5 38 46 64 3.81.4 156 17.6 1.8 184 22 2.5 235 33 3.9 330 48 6.0 475 68 4.2 1.5 30 43 58 4.91.8 184 17.6 2.1 210 22 2.8 260 33 4.2 360 48 6.7 525 68 4.2 2.0 33 43 61 5.2.70 102 36 1.1 130 45 1.8 184 68 3.2 285 100 5.3 430 141 2.8 .70 46 58 81 4.01.1 130 36 1.4 156 45 2.1 210 68 3.5 310 100 6.0 475 141 3.2 1.5 48 58 79 4.31.4 156 36 2.1 210 45 2.8 260 68 4.9 405 100 6.7 525 141 5.6 1.5 38 51 66 5.81.8 184 36 2.5 235 45 3.2 285 68 5.9 455 100 7.0 550 141 3.9 2.0 48 64 84 4.31.0 102 36 1.8 139 45 2.5 178 68 3.2 212 100 3.9 255 141 1.0 .20 15.0 20 25 2.71.4 116 36 2.1 156 45 2.8 195 68 3.5 227 100 4.2 275 141 2.1 .20 15.0 22 29 3.01.8 139 36 2.5 178 45 3.2 212 68 3.9 246 100 4.6 297 141 2.8 .35 18.0 24 36 3.52.1 156 36 2.8 195 45 3.5 227 68 4.2 266 100 4.9 314 141 3.2 1.4 20 28 39 3.72.5 178 36 3.2 212 45 4.2 266 68 4.9 312 100 5.6 360 141 3.5 .70 19.0 27 38 4.02.8 195 36 3.5 227 45 4.9 312 68 5.6 360 100 6.3 411 141 4.2 1.4 20 28 39 4.33.5 227 36 4.2 266 45 5.6 360 68 6.3 411 100 7.0 453 141 5.6 2.8 18.0 24 38 5.91.8 235 36 1.8 235 45 2.5 300 68 3.9 410 100 — — — 1.8 .20 15.0 20 29 3.02.1 260 36 2.1 260 45 2.8 330 68 4.2 445 100 — — — 2.8 .20 15.0 20 30 3.42.5 300 36 2.5 300 45 3.2 355 68 4.6 480 100 — — — 2.8 .30 15.0 20 30 4.02.8 330 36 2.8 330 45 3.5 380 68 4.9 529 100 — — — 3.5 .70 17.0 22 32 4.33.2 355 36 3.2 355 45 3.9 410 68 5.3 565 100 — — — 3.9 1.5 17.0 22 34 4.63.5 380 36 3.5 380 45 4.2 445 68 5.6 600 100 — — — 4.2 1.0 17.0 23 33 4.74.2 445 36 4.2 445 45 4.9 520 68 6.3 685 100 — — — 4.9 1.5 17.0 23 34 5.5A(cm)B(cm)C(cm)D(m)76

Air Atomizing NozzlesSpangling/Cold Strip MillPerformance – Air Atomizing Flat External Mix Spray NozzlesSpray SetupNo.SUE45ASUE45Spray Set-upConsists ofFluid andAir CapCombinationFluid Cap80150+Air Cap200278-45°Fluid Cap100150+Air Cap200278-45°AirPress.(bar)Liquid Capacity (liters per hour) and Air Capacity (liters per minute)Liquid Pressure (bar)0.2 0.3 0.7 1.5 3Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.AirPress.(bar)Airl/minl/hr.Air(bar)Liquid(bar)Spray Dimensions2.1 260 64 2.8 330 78 3.9 410 119 4.9 520 175 — — — 2.1 .20 17.0 24 34 3.52.5 300 64 3.2 355 78 4.2 445 119 5.3 565 175 — — — 3.2 .20 18.0 24 36 4.32.8 330 64 3.5 380 78 4.6 480 119 5.6 600 175 — — — 3.9 .30 18.0 25 36 4.93.2 355 64 3.9 410 78 4.9 520 119 6.0 640 175 — — — 4.9 .70 18.0 25 36 5.53.5 380 64 4.2 445 78 5.3 565 119 6.3 685 175 — — — 4.9 1.5 20 25 38 5.54.2 445 64 4.9 520 78 5.6 600 119 — — 175 — — — 5.3 1.0 18.0 25 38 5.84.9 520 64 5.6 600 78 6.3 685 119 — — 175 — — — 5.6 1.5 20 25 38 6.12.8 330 102 3.5 380 125 4.6 480 192 5.6 600 280 — — — 2.8 .20 19.0 25 36 4.63.2 355 102 3.9 410 125 4.9 520 192 6.0 640 280 — — — 3.9 .20 20 25 37 4.93.5 380 102 4.2 445 125 5.3 565 192 6.3 685 280 — — — 4.6 .30 20 25 37 5.23.9 410 102 4.6 480 125 5.6 600 192 — — 280 — — — 5.3 .70 22 27 38 5.54.2 445 102 4.9 520 125 6.0 640 192 — — 280 — — — 5.6 1.0 22 27 41 5.54.6 480 102 5.3 565 125 6.3 685 192 — — 280 — — — 5.6 1.5 22 27 41 5.84.9 520 102 5.6 600 125 — — 192 — — 280 — — — 6.0 1.5 22 27 41 6.1A(cm)B(cm)C(cm)D(m)77

Dust Control/Gas CoolingEffective Dust Control and Gas ConditioningDepends on Drop Size… And We Have theSystems, Nozzles and Data You NeedWhether you’re looking for hydraulic spray nozzles for dust control or gas cooling,energy-efficient air atomizing nozzles for evaporative cooling or a fully automatedsystem for gas conditioning, you’ll find we have a wide assortment ofproven solutions.WhirlJet and SpiralJet ® Nozzles –Ideal for Dust Absorption and Gas CoolingStandard WhirlJet spray nozzles feature a hollow cone spray patternwith a ring-shaped impact area. They produce a uniform distributionof small- to medium-sized drops over a wide range of flow rates andpressures and are well-suited to pollution control applications in millsthat require good atomization of liquids at lower pressures, quick heattransfer or effective airborne drop impingement. WhirlJet nozzles alsofeature large and unobstructed flow passages, which minimize or eliminateclogging.Specifications:• Model A and B WhirlJet spray nozzles have removable caps and the originalWhirlJet whirlchamber design• Model AX and BX WhirlJet spray nozzles feature the same uniform spray distributionand two-piece construction as the A and B Series plus a slope-bottomdesign which reduces the “drilling effect” of the fluid vortex in the whirlchamber• Model C and D WhirlJet spray nozzles feature one-piece cast construction witha precision-machined finish and the original WhirlJet whirlchamber design foruniform spray distribution• Model CX slope-bottom WhirlJet nozzles feature the same uniform spray performanceas the C Series, plus the added advantage of the patented, longer-life,slope-bottom design to reduce the “drilling effect” of the liquid vortex in thewhirlchamber• Model CRC two-piece WhirlJet spray nozzles feature a hollow cone spray patternwith a ring-shaped impact area. They are available in two spray angleseries: narrow angle 45° to 52° and standard angle 60° to 86° with flow rate of140 gpm at 7 psi (530 l/min at .5 bar)78

Dust Control/Gas CoolingSpiralJet nozzles are also widely used in dust control and gas cooling. Choosefrom three types: BSJ, HHSJ or HHSJX SpiralJets.Similar to WhirtlJet ® nozzles, BSJ SpiralJet nozzles produce a hollow cone spraypattern. These compact nozzles permit maximum liquid output for a given pipe sizeand the free passage design minimizes clogging.BSJ Specifications:• Spray angles: 50° to an extra wide angle of 180°• Materials: Brass, 316 stainless steel, PVC or TEFLON®• Brass nozzles have hex or flats design depending on connection size• Stainless steel nozzles have hex or flats design depending on capacity size• PVC and TEFLON ® nozzles have rounded design• Designed with precision impact blade angles that distribute the spray drops forexcellent coverage• Flanged versions available in reaction-bonded silicon carbide• Custom-sized for your installation and available in several abrasion-resistantmaterialsHHSJ SpiralJet nozzles produce a full cone spray pattern. Similar to our hollowcone SpiralJet nozzles, the HHSJ nozzles permit maximum liquid output for a givenpipe size and feature a clog-resistant free passage design.HHSJ Specifications:• 3” and 4” sizes are available in brass and stainless steel• Brass version is available with hex design. Stainless steel nozzles are availablewith flats• TEFLON ® and PVC nozzles have a rounded designHHSJX Specifications:HHSJX Extra Large Free Passage SpiralJet nozzles minimize the possibility of pluggingin high-flow pollution control applications. With a simple one-piece design,the inlet orifice is the smallest opening that liquid passes through. The outlet helixorifice is proportionately larger than the inlet opening. This virtually eliminatesplugging and allows for maximum liquid output.• Standard materials: Brass, cast 316 stainless steel, PVC and polypropylene• Additional materials available upon request: TEFLON ® , silicon carbide, Stellite ® ,Hastelloy ® C and ceramic• Spray Angles: 90° or 120° with full cone spray patterns• HHSJX nozzle is available in threaded/hex, threaded/round and threaded/flats79

Dust Control/Gas CoolingPerformance — WhirlJet Nozzles*At the stated pressure in bar.NozzleInletConn.NPT orBSPT(in.)1/81/43/81/23/4Nozzle TypeCapacitySizeInlet Dia.Nom.(mm)OrificeDia.Nom.(mm)Capacity (Liters per minute)*Spray AngleDegree*A AX B BX 0.2 0.5 1 1.5 2 3 4 5 6 7 0.5 1.5 6● ● ● ● .5 .79 1.2 — .16 .23 .28 .32 .39 .46 .51 .56 .60 — 58 69● ● ● ● 1 1.6 1.6 — .32 .46 .56 .64 .79 .91 1.0 1.1 1.2 — 64 76● ● ● ● 2 2.0 2.0 — .64 .91 1.1 1.3 1.6 1.8 2.0 2.2 2.4 52 61 69● ● ● ● 3 2.4 2.4 — .97 1.4 1.7 1.9 2.4 2.7 3.1 3.3 3.6 52 64 77● ● ● ● 5 3.2 3.2 1.0 1.6 2.3 2.8 3.2 3.9 4.6 5.1 5.6 6.0 56 67 76● ● ● ● 8 4.0 4.0 1.6 2.6 3.6 4.5 5.2 6.3 7.3 8.2 8.9 9.6 56 65 70● ● ● ● 10 4.4 4.4 2.0 3.2 4.6 5.6 6.4 7.9 9.1 10.2 11.2 12.1 55 65 72● ● ● ● 1 1.6 1.6 — — .38 .45 .53 .64 .76 .90 1.0 1.2 — 53 67● ● ● ● 2 2.0 2.0 — — .76 .95 1.0 1.3 1.5 1.8 2.1 2.4 — 62 71● ● ● ● 3 2.4 2.4 — .79 1.1 1.9 1.6 2.0 2.3 2.8 3.2 3.6 51 65 78● ● ● ● 5 3.6 3.6 1.0 1.3 1.9 2.3 2.6 3.3 3.8 4.5 5.3 6.1 63 73 79● ● ● ● 8 4.0 4.0 1.7 2.1 3.0 3.7 4.2 5.3 6.1 7.6 8.7 9.5 61 69 73● ● ● ● 10 4.8 4.4 2.1 2.7 3.8 4.5 5.3 6.4 7.6 9.5 10.6 12.1 63 70 74● ● ● ● 15 5.9 5.2 3.1 4.2 5.7 6.8 7.9 9.8 11.4 14 15.9 17.8 63 71 72● ● ● ● 5 3.6 3.2 1.0 1.6 2.3 2.8 3.2 3.9 4.6 5.1 5.6 6.0 64 73 79● ● ● ● 8 4.4 4.0 1.6 2.6 3.6 4.5 5.2 6.3 7.3 8.2 8.9 9.6 62 70 74● ● ● ● 10 5.2 4.4 2.0 3.2 4.6 5.6 6.4 7.9 9.1 10.2 11.2 12.1 64 72 75● ● ● ● 15 5.9 5.6 3.1 4.8 6.8 8.4 9.7 11.8 13.7 15.3 16.7 18.1 64 72 74● ● ● ● 20 7.1 6.4 4.1 6.4 9.1 11.2 12.9 15.8 18.2 20 22 24 63 70 74● ● ● ● 25 7.5 7.5 5.1 8.1 11.4 14.0 16.1 19.7 23 25 28 30 63 70 74● ● ● ● 30 8.3 7.9 6.1 9.7 13.7 16.7 19.3 24 27 31 33 36 63 70 74● ● 15-30.1 5.9 7.9 4.7 7.4 10.5 12.8 14.8 18.2 21 23 26 28 40 50 54● ● 25-30.1 7.5 7.9 5.7 9.0 12.8 15.6 18 22 26 29 31 34 40 47 51● ● 50-50.1 8.7 9.5 10.2 16.1 23 28 32 39 46 51 56 60 40 47 50● ● 50-50.3 8.7 9.5 10.2 16.1 23 28 32 39 46 51 56 60 72 76 78● ● ● ● 25 9.5 6.4 5.1 8.1 11.4 14 16.1 19.7 23 25 28 30 63 66 71● ● ● ● 30 9.5 7.5 6.1 9.7 13.7 16.7 19.3 24 27 31 33 36 67 71 75● ● ● ● 40 9.5 9.1 8.2 12.9 18.2 22 26 32 36 41 45 48 72 76 78● ● ● ● 50 9.5 11.1 10.2 16.1 23 28 32 39 46 51 56 60 74 79 82● ● ● ● 60 9.5 13.1 12.2 19.3 27 33 39 47 55 61 67 72 77 82 86● ● ● ● 40 12.7 7.9 8.2 12.9 18.2 22 26 32 36 41 45 48 70 73 74● ● ● ● 50 12.7 9.5 10.2 16.1 23 28 32 39 46 51 56 60 72 75 77● ● ● ● 60 12.7 11.1 12.2 19.3 27 33 39 47 55 61 67 72 74 76 79● ● ● ● 70 12.7 12.7 14.3 23 32 39 45 55 64 71 78 84 76 79 83● ● ● ● 80 12.7 14.3 16.3 26 36 45 52 63 73 82 89 96 78 82 84● ● ● ● 90 12.7 14.7 18.3 29 41 50 58 71 82 92 100 109 81 84 84● ● ● ● 100 12.7 15.9 20 32 46 56 64 79 91 102 112 121 83 86 86● ● ● ● 110 12.7 17.1 22 35 50 61 71 87 100 112 123 133 85 88 88● ● ● ● 120 12.7 18.3 24 39 55 67 77 95 109 122 134 145 87 90 9080

Dust Control/Gas CoolingPerformance — WhirlJet CX, C, D Nozzles*At the stated pressure in bar.NozzleInletConn.NPT orBSPT(in.)Nozzle TypeCapacitySizeInletDia.Nom.(mm)OrificeDia.Nom.(mm)Capacity (Liters per minute)*Spray AngleDegree*CX C D 0.2 0.3 0.5 0.7 1 1.5 2 3 4 5 6 7 0.7 1.5 4● 3 11.1 7.5 7.3 9.0 11.6 13.7 16.3 20 23 28 33 37 40 43 60 63 65● 4 11.1 9.5 9.7 11.9 15.4 18.2 22 27 31 38 44 49 53 58 68 71 73● 5 11.1 11.5 12.2 14.9 19.3 23 27 33 39 47 54 61 66 72 74 77 801/23/411-1/41-1/222-1/2● 7 11.1 13.5 17.1 21 27 32 38 47 54 66 76 85 93 101 77 80 83● 3 11.1 7.9 7.3 9.0 11.6 13.7 16.3 20 23 28 33 37 40 43 62 65 67● 4 11.1 9.9 9.7 11.9 15.4 18.2 22 27 31 38 44 49 53 58 68 71 73● 5 11.1 11.9 12.2 14.9 19.3 23 27 33 39 47 54 61 66 72 74 77 80● 7 11.1 13.9 17.1 21 27 32 38 47 54 66 76 85 93 101 77 80 83● ● ● 5 15.1 9.9 12.2 14.9 19.3 23 27 33 39 47 54 61 66 72 59 61 63● ● ● 6 15.1 11.5 14.6 17.9 23 27 33 40 46 57 65 73 80 86 62 64 66● ● ● 7 15.1 12.7 17.1 21 27 32 38 47 54 66 76 85 93 101 70 71 72● ● ● 10 15.1 16.7 24 30 39 46 54 67 77 94 109 122 133 144 73 75 77● 7 17.5 11.5 17.1 21 27 32 38 47 54 66 76 85 93 101 64 65 66● 8 17.5 12.7 19.5 24 31 36 44 53 62 75 87 97 107 115 65 66 67● 9 17.5 14.3 22 27 35 41 49 60 69 85 98 110 120 130 66 67 69● 10 17.5 15.5 24 30 39 46 54 67 77 94 109 122 133 144 67 69 71● 12 17.5 17.1 29 36 46 55 65 80 92 113 131 146 160 173 70 73 75● 15 17.5 20.6 37 45 58 68 82 100 116 142 163 183 200 215 76 79 81● 10 21.4 14.3 24 30 39 46 54 67 77 94 109 122 133 144 65 67 67● 12 21.4 16.3 29 36 46 55 65 80 92 113 131 146 160 173 68 70 71● 14 21.4 18.3 34 42 54 64 76 93 108 132 153 171 187 200 71 73 75● 16 21.4 20.2 39 48 62 73 87 107 123 151 174 195 215 230 74 75 77● 20 21.4 24.2 49 60 77 91 109 133 154 189 220 245 265 290 76 77 79● 16 27.8 17.5 39 48 62 73 87 107 123 151 174 195 215 230 64 67 69● 20 27.8 21.8 49 60 77 91 109 133 154 189 220 245 265 290 69 72 74● 25 27.8 25.8 61 75 96 114 136 167 193 235 270 305 335 360 72 74 76● 30 27.8 28.6 73 90 116 137 163 200 230 285 325 365 400 430 74 76 78● 30 36.5 23.8 73 90 116 137 163 200 230 285 325 365 400 430 66 67 70● 35 36.5 27 85 104 135 160 191 235 270 330 380 425 465 500 68 70 73● 40 36.5 30.2 97 119 154 182 220 265 310 375 435 490 530 580 70 72 75● 45 36.5 32.9 110 134 173 205 245 300 345 425 490 550 600 650 72 74 78● 50 36.5 36.1 122 149 193 230 270 335 385 470 540 610 670 720 74 77 82● 60 36.5 39.7 146 179 230 275 325 400 460 570 650 730 800 860 77 79 84● 60 47.6 36.1 146 179 230 275 325 400 460 570 650 730 800 860 67 68 7170 47.6 40.5 171 210 270 320 380 465 540 660 760 850 930 1010 69 71 7480 47.6 44.1 195 240 310 365 435 535 620 750 870 970 1070 1150 71 73 7790 47.6 47.6 220 270 345 410 490 600 690 850 980 1100 1200 1300 73 75 80100 47.6 50.8 245 300 385 455 540 670 770 940 1090 1220 1330 1440 77 79 8381

Dust Control/Gas CoolingDimensions — WhirlJet NozzlesNozzle Type (Conn.)A, AX(F)B, BX(M)C(F)InletConn.(in.)A (in.)A(mm)B (in.)B(mm)C (in.)C(mm)D (in.)D(mm)L (in.)L(mm)NetWeight(oz.)1/8 11/16 17.5 5/8 16.0 15/32” 12.0 25/32 20 1 25.5 1-1/2 .041/4 7/8 22.5 3/4 19.0 17/32” 13.5 29/32 23 1-1/4 32 2-3/4 .083/8 1-1/32 26.5 7/8 22.5 11/16” 17.5 1-1/8 28.5 1-15/32 37.5 4-1/4 .121/2 1-3/8 35 1-1/8 28.5 27/32” 21.5 1-13/32 36 1-15/16 49.5 8-3/4 .253/4 1-9/16 40 1-1/4 32 15/16 24 1-9/16 40 2-3/16 55.5 11 .311/8 7/8 22.5 5/8 16.0 15/32” 12.0 25/32 20 1-3/16 30.5 1-1/2 .041/4 1 25.5 3/4 19.0 17/32 13.5 29/32 23 1-3/8 35 2-1/2 .073/8 1-1/8 28.5 7/8 22.5 11/16 17.5 1-1/8 28.5 1-9/16 40 4 .111/2 1-3/8 35 1-1/8 28.5 27/32 21.5 1-13/32 36 1-15/16 49.5 7 .203/4 1-5/8 41.5 1-1/4 32 15/16 24 1-9/16 40 2-1/4 57.5 10-3/4 .311/2 1-5/16 33.5 1-5/16 33.5 7/32 5.5 23/32 18.5 1-7/8 48 4-1/2 .133/4 1-1/2 38 1-21/32 42 19/64 7.5 29/32 23 2-9/32 58 7 .201 1-3/4 44.5 1-27/32 47 11/32 9.0 1-1/32 26 2-5/8 66.5 11 .31NetWeight(kg)1-1/4 2-1/16 50.9 2-3/16 55.6 7/16 11.1 1-1/4 31.7 3-1/16 77.8 20 .57 CX(F)1-1/2 2-7/16 61.9 2-7/8 73 9/16 14.3 1-21/32 42.1 3-11/16 93.6 28 .792 2-15/16 74.6 3-11/16 93.6 23/32 18.2 2-3/32 53.1 4-17/32 115.1 48 1.42-1/2 3-1/2 88.9 4-1/2 114.3 15/16 23.8 2-11/16 68.3 5-17/32 140.5 68 1.91/2 1-3/4 44.5 1-5/16 33.5 1/4 6.5 23/32 18.5 2-5/16 59 5 .14D(M)3/4 2 51 1-21/32 42 5/16 8.0 15/16 24 2-23/32 69 7-1/2 .21Based on largest/heaviest version of each type.Materials — WhirlJet NozzlesNozzleMaterialMaterialA AX B BX C CX DBrass (none) ● ● ● ● ●Mild Steel I ● ● ● ●303 Stainless Steel SS ● ● ● ●316 Stainless Steel 316SS ● ● ● ●Polyvinyl Chloride PVC ● ●Cast: Iron I ● ● ●Cast: Brass (none) ● ●Cast: 316 Stainless Steel SS ● ●Ordering InfoWhirlJet Spray Nozzle1/4 A — SS 10Inlet Nozzle Material CapacityConn. Type Code SizeOther materials availbale upon request.82

Dust Control/Gas CoolingPerformance — SpiralJet BSJ Nozzles*At the stated pressure in bar.Nozzle InletConn. NPT orBSPT (in.)1/4**3/8**1/2Spray Angle Degree at 0.7 barMax. FreeCapacity (Liters per minute)*Capacity Orifice Dia.Passage50 60 90 120 180 Size Nom. (mm)Dia. (mm) 0.3 0.7 1.5 3 7 25***● ● ● ● 07 2.4 2.4 1.7 2.6 3.9 5.5 8.4 16● ● ● ● ● 13 3.2 3.2 3.2 4.9 7.3 10.3 15.7 30● ● ● ● ● 20 4.0 3.2 5 7.6 11.2 15.8 24 46● ● ● ● ● 30 4.8 3.2 7.5 11.4 16.7 24 36 68● ● ● ● ● 40 5.6 3.2 9.9 15.1 22 32 48 91● ● ● ● ● 53 6.4 3.2 13.1 20 30 42 64 121● ● ● ● ● 82 7.9 3.2 20.3 31 46 65 99 187● ● ● ● ● 120 9.5 4.8 29.5 45 67 95 145 270● ● ● ● ● 164 11.1 4.8 40.6 62 92 129 198 3703/4 ● ● ● ● ● 210 12.7 4.8 56 80 117 166 255 48011-1/223● ● ● ● 340 15.9 6.4 91 130 190 270 410 775● ● ● ● 470 19.1 6.4 125 179 260 370 565 1070● ● ● ● 640 22.2 7.9 170 245 355 505 770 1460● ● ● ● 820 25.4 7.9 219 310 455 645 990 1870● ● ● ● 960 28.6 7.9 257 365 535 755 1160 2190● ● ● ● 1400 34.9 11.1 375 535 780 1105 1690 3190● ● ● ● 1780 38.1 11.1 477 680 995 1405 2150 4060● ● ● 2560 44.5 14.3 685 980 1430 2020 3090 5830● ● ● 3360 50.8 14.3 901 1280 1880 2650 4050 76604 ● ● ● 5250 63.5 15.9 1404 2000 2930 4140 6330 11960** For all 1/4 and 3/8 connection size SpiralJets, optimum spray angle is achieved at 40 psi (3 bar).*** Maximum operating pressure depends on material, size and application. Call for specific recommendations.DimensionsNozzle TypeBSJ(M)InletConn.(in.)Length(in.)Based on largest/heaviest version of each type.Length(mm)Hex.(in.)Hex(mm)NetWeight(oz.)NetWeight(kg)1/4 1-7/8 47.6 9/16 14.3 1.0 .033/8 1-7/8 47.6 11/16 17.5 1.8 .051/2 2-1/2 63.5 7/8 22.2 3.0 .083/4 2-3/4 69.8 1-1/16 27 5 .141 3-5/8 92.1 1-3/8 34.9 11 .311-1/2 4-3/8 111.1 2 50.8 1.7 lbs. .772 6-7/8 174.6 2-1/2 63.5 3 lbs. 1.43 8 203.2 3-3/4 95.2 7.8 lbs. 3.64 9 228.6 4-1/2 114.3 12.3 lbs. 5.6MaterialsMaterialOrdering InfoMaterialCodeSpiralJet Spray Nozzle1/4 BSJ — SS 120 07Nozzle TypeBSJBrass (none) ●TEFLON TEF ●Polyvinyl Chloride PVC ●Cast: 316 Stainless Steel SS ●Other materials available upon request.Inlet Nozzle Material Spray CapacityConn. Type Angle Code Size83

Dust Control/Gas CoolingPerformance — SpiralJet HHSJ Nozzles*At the stated pressure in bar.Nozzle InletConn. NPT orBSPT (in.)1/4**3/8**1/2Spray Angle Degree at 0.7 barMax. FreeCapacity (Liters per minute)*Capacity Orifice Dia.Passage Dia.60 90 120 150 170 Size Nom. (mm)(mm) 0.7 1.5 3 7 25***● ● ● 07 2.4 2.4 2.6 3.9 5.5 8.4 16.0● ● ● ● ● 13 3.2 3.2 4.9 7.3 10.3 15.7 30● ● ● ● ● 20 4.0 3.2 7.6 11.2 15.8 24 46● 07 2.4 2.4 2.6 3.9 5.5 8.4 16.0● 13 3.2 3.2 4.9 7.3 10.3 15.7 30● 20 4.0 3.2 7.6 11.2 15.8 24 46● ● ● ● ● 30 4.8 3.2 11.4 16.7 24 36 68● ● ● ● ● 40 5.6 3.2 15.1 22 32 48 91● ● ● ● ● 53 6.4 3.2 20 30 42 64 121● ● ● ● ● 82 7.9 3.2 31 46 65 99 187● ● ● ● ● 120 9.5 4.8 45 67 95 145 270● ● ● ● ● 164 11.1 4.8 62 92 129 198 370● 210 12.7 4.8 80 117 166 255 4803/4 ● ● ● ● ● 210 12.7 4.8 80 117 166 255 48011-1/223● ● ● ● ● 340 15.9 6.4 130 190 270 410 775● ● ● ● ● 470 19.1 6.4 179 260 370 565 1070● ● ● ● ● 640 22.2 7.9 245 355 505 770 1460● ● ● ● ● 820 25.4 7.9 310 455 645 990 1870● ● ● ● ● 960 28.6 7.9 365 535 755 1160 2190● ● ● ● ● 1400 34.9 11.1 535 780 1105 1690 3190● ● ● ● ● 1780 38.1 11.1 680 995 1405 2150 4060● ● ● 2560 44.5 14.3 980 1430 2020 3090 5830● ● ● 3360 50.8 14.3 1280 1880 2650 4050 76604 ● ● ● 5250 63.5 15.9 2000 2930 4140 6330 11960** For all 1/4 and 3/8 connection size SpiralJets, optimum spray angle is achieved at 40 psi (3 bar)*** Maximum operating pressure depends on material, size and application. Call for specific recommendations.DimensionsNozzle Type (Conn.)HHSJ(M)InletConn.(in.)Length(in.)Length(mmHex.(in.)Hex(mm)NetWeight(oz.)NetWeight(kg)1/4 2-1/8 53.9 9/16 14.3 1 .033/8 2-3/8 60.3 11/16 17.5 1-3/4 .051/2 3-1/8 79.4 7/8 22.2 3.5 .103/4 3-7/16 87.3 1-1/16 27 5.4 .151 4-9/16 116 1-3/8 34.9 10.1 .291-1/2 6-3/4 171 2 50.8 27 .772 6-7/8 175 2-1/2 63.5 35 .993 11-7/8 302 3-3/4 95.34 9 229 4-1/2 114.35 lbs. 12oz10 lbs.3 oz2.64.6MaterialsMaterialOrdering InfoMaterialCodeSpiralJet HHSJ Spray Nozzle3/4 HHSJ — SS 120 210Nozzle TypeHHSJBrass (none) ●Polyvinyl Chloride PVC ●TEFLON TEF ●Cast: 316 Stainless Steel SS ●Other materials available upon requestBased on largest/heaviest version of each type.Inlet Nozzle Material Spray CapacityConn. Type Angle Code Size84

Dust Control/Gas CoolingPerformance — SpiralJet HHSJX Nozzles*At the stated pressure in bar.Nozzle InletConn. NPT orBSPT (in.)3/8**1/2Spray AngleMax. FreeDegree at 0.7 bar Capacity Orifice Dia.Capacity (Liters per minute)*Passage Dia.Size Nom. (mm)90 120 (mm)0.7 1.5 3 7 25***● ● 30 4.8 4.8 11.4 16.7 24 36 68● ● 40 5.6 5.6 15.1 22 32 48 91● ● 53 6.4 6.4 20 30 42 64 121● ● 82 7.9 7.9 31 46 65 99 187● ● 120 9.5 9.5 45 67 95 145 270● ● 164 11.1 11.1 62 92 129 198 3703/4 ● ● 210 12.7 12.7 80 117 166 255 48011-1/22● ● 340 15.9 15.9 130 190 270 410 775● ● 470 19.1 19.1 179 260 370 565 1070● ● 640 22.2 22.2 245 355 505 770 1460● ● 820 25.4 25.4 310 455 645 990 1870● ● 960 28.6 28.6 365 535 755 1160 2190● ● 1400 34.9 34.9 535 780 1105 1690 3190● ● 1780 38.1 38.1 680 995 1405 2150 4060** For all 1/4 and 3/8 connection size SpiralJets, optimum spray angle is achieved at 40 psi (3 bar)*** Maximum operating pressure depends on material, size and application. Call for specific recommendations.DimensionsNozzle Type (Conn.)HHSJX(M)InletConn.(in.)Length(in.)Based on largest/heaviest version of each type.Length(mmHex.(in.)Hex(mm)NetWeight(oz.)NetWeight(kg)3/8 2-3/4 69 7/8 22.2 3 .091/2 3-3/8 85 1-1/16 26.9 4.5 .183/4 4-5/8 117 1-3/8 34.9 8 .231 5-1/8 130 1-3/4 44.5 18 .511-1/2 6-3/4 171 2 50.8 30 .852 11 279 3 76.25 lbs. 8oz.2.5MaterialsMaterialOther materials available upon request.Ordering InfoMaterialCodeSpiralJet HHSJX Spray NozzleNozzle TypeHHSJXBrass (none) ●Polypropylene PP ●Polyvinyl Chloride PVC ●Cast: 316 Stainless Steel SS ●3/4 HHSJX — SS 120 210Inlet Nozzle Material Spray CapacityConn. Type Angle Code Size85

Emission Control/Scrubber/Gas ConditioningFloMax ®FloMax Nozzles Provide UnmatchedEfficiency in Evaporative Gas CoolingVery few air atomizing nozzles are suitable for use in gas conditioning since tightcontrol of drop size and spray coverage is required to cool hot gases and reducegas volume. And, of those that are suitable, none offer the performance ofour FloMax Air Atomizing nozzles. FloMax nozzles use a patented threestageatomization process to produce very small drops using less airthan competitive nozzles.The competitive advantages of FloMax nozzles extend beyond drop size.• Higher turndown ratios• Large flow rates per nozzle so fewer nozzles are required for cooling• Special materials such as Hastelloy® and Stellite® are available in addition to 316and 310 stainless steel• Large free passage allows flexibility in water sourcesFloMax nozzles are available in a wide range of flow rates:Nozzle Type Capacity (gpm) Capacity (l/min)FM 1 0.5 to 2.5 1.8 to 9.5FM 5 2.0 to 7.0 7.6 to 26.5FM 10 4.0 to 13.0 15.0 to 49.2FM 25 15.0 to 30.0 57.0 to 114FM 40 14.0 to 52.0 53.0 to 197FloMaxPrincipleof Operation34% SmallerDrop size reduces dwell timefor complete evaporation.Stage Three: Final MixingAir cap acts as a final mixing chamber.As liquid crosses multiple orifices, anadditional pressure drop provides thefinal atomization.Stage One: Primary Fluid BreakupAir and liquid combine behind the airguide. The pressure drop across the airguide orifice provides primary atomizationof the liquid stream.Stage Two: Secondary Fluid BreakupFocused stream impacts the targetbolt forcing additional mechanicalbreakup.86

Emission Control/ScrubberGas ConditioningAutoJet Gas Conditioning Systems:A Completely Automated Solution thatResults in Even Greater EfficienciesMany mills can benefit from a totally automated solution to ensure optimal gascooling and reduce labor costs and downtime. Our AutoJet ® Gas ConditioningSystem is designed to maximize the performance of FloMax nozzles and providestotal automation.System Overview:• Our AutoJet Spray Controller, with patent-pending SprayLogic® firmware andsoftware, monitors and automatically adjusts the closed loop system. By regulatingliquid and air flow to the nozzles based on data gathered from RTD temperaturesensors, the controller offers the highest level of reactivity and accuracy forthe system.• The AutoJet Spray Controller is pre-programmed with parameters and functionscreens specific to gas conditioning applications, saving time and money duringsystem implementation.• All system components – nozzles, pumps, sensors and other hydraulic/pneumaticcomponents – are controlled by the AutoJet Spray Controller. If a problem isdetected that the controller can’t resolve automatically, operator warnings will bedisplayed or sounded.• Multiple lance zones can be configured to allow greater turndown of flow rateunder variable system conditions. The AutoJet Spray Controller can preciselycontrol spray performance of multiple FloMax nozzle lances in multiple lancezones.• Variable Frequency Drive (VFD) pumps provide proportional liquid regulation andsignificant electricity savings. In addition, energy-efficient proportional air regulationreduces air consumption and operating costs.• The AutoJet Spray Controller is easy touse and is equipped with complete spray“knowledge”. Just provide informationabout your operation using the menusystem and the controller will essentiallyconfigure itself.• The AutoJet Gas Conditioning Systemcan operate independently or can be integratedwith other plant control systems.87

Other CapabilitiesCustom Header FabricationOur sales engineers work closely with our factory engineers to understand yourprocess and performance requirements so we can assist with header specifications.In addition to having more than 100 years of cumulative experience in spraytechnology, our engineers have both state-of-the-art and proprietary tools to helpwith header specification. Computational Fluid Dynamics (CFD) software is used forapplication simulation and modeling and a proprietary software program is usedfor heat transfer calculations.Design and construction to globally recognized standards:• ASME Boiler and Pressure Vessel Code• ASME B31.1 Power Piping Code• ASME B31.3 Process Piping Code• Welding to ASME B&PV Code Section IX• Other requirements can be met upon requestTesting in accordance with ANSI and ASTM standards.Destructive and non-destructive examinations:• Ultrasonic• Radiographic• Liquid penetrant• Hardness testing• Hydrostatic testing• Spray and flow testing• Magnetic particle examination• Positive material identificationTypical Applications• Descale lines• Roll cooling• Quenching• Pickle lines• Oiling/coatingTrademarksHastelloy ® is a registered trademark of Haynes InternationalStellite ® is a registered trademark of Stoody Deloro Stellite, Inc.Viton ® is a registered trademark of DuPont Dow ElastomersTEFLON ® is a registered trademark of E.I. DuPont de Nemours and Company88

Other Helpful Resources:Industrial Spray ProductsCatalog 60Features our complete line of spray nozzles and accessories. U.S. and Metricversions available.FloMax Air Atomizing NozzlesBulletin 487BFeatures details and performance data on the unmatched energy-efficient FloMax ®nozzles and lances.An Engineer’s Practical Guide to Drop SizeBulletin 459An invaluable technical guide. We’ve taken 60 years of spray drop knowledge andcondensed it into a 28-page booklet to teach you the fundamentals of evaluating andinterpreting drop size data.Optimizing System Performancewith Precision Spray ControlBulletin AT103BProvides an overview of the benefits of automated spray systems. Included areapplication examples that show how to reduce overspray, improve product quality,increase throughput and improve regulatory compliance.Model 2250 AutoJet Spray ControllerBulletin AT105BFeatures the specification information and details of our unique control package thatautomates and optimizes spray performance.Optimizing Your Spray SystemTechnical Manual 410Explains how to maximize performance and quality in your spray application.Easily specify and order your nozzles online at www.spray.com/iSprayP.O. Box 7900, Wheaton, IL 60189-7900 USATel: 1.800.95.SPRAY Intl. Tel: 1.630.665.5000Fax: 1.888.95.SPRAY Intl. Fax: 1.630.260.0842www.spray.comCatalog No. 44AM Printed in the U.S.A. ©Spraying Systems Co. 2005