Download PDF - Hainbuch GmbH

That makes senseThe modular system for turningand milling operationsHAINBUCH: Flexible clamping solutions with quick change-overwww.hainbuch.com

The HAINBUCH modular system.Flexibility is trumpClamping devicesrotatingClamping elementTOPlus chuckSPANNTOP chuckClamping head – O.D. clampingcircumferential clamping3 different versions: for raw material,precision machining, and for in-housemachiningan abundance of profile clampingpossibilitiescoolant-resistant, rubber-metalconnection, prevents chips in the chuckAdaptation clamping devicestationaryTOROK manual chuckMANDO Adapt mandrel –I.D. clampingquick change-over from O.D. toI.D. clamping without adjusting,due to CENTREX interfaceconcentricity < 0.005 mm canbe achieved between chuck taperand mandrel taper8 different mandrel sizesclamping range Ø 8 – 120 mmavailable with and without draw boltMANOK plus manual stationary chuckHYDROK hydraulic stationary chuckJaw adapter – clamping infront of the chuckapprox. double the clamping Ø canbe realizeddrilling and milling between the jawsinstallation and removal with taperedbolts – without changing fixtureloading plug for in-house machiningof the soft jaws

TOPlus chuck. Six to winTOPlus25 % higher holding power than SPANNTOPunequalled rigidity due to full-surface contactof the clamping segmentsno radial displacement between clampinghead and chuck body, therefore it is resistantto contaminationconcentric precision < 0.015 mm possibleabsorbs vibrationClamping elementsAdaptationsMANDO Adapt T211SE [ with draw bolt ]Clamping head SEMANDO Adapt T212SE [ without draw bolt ]Jaw adapter SESPANNTOP nova chuck. The original, that wrote workholding historySPANNTOP novatypical HAINBUCH features, such as user friendlyset-up, full passage, parallel clamping, optimalpower conversion, extreme rigidity and superiorholding power, as well as minimal wear and tearconcentric precision < 0.01 mm possibleminimal effects of inertia lossClamping elementsAdaptationsClamping head RDMANDO Adapt T211RD [ with draw bolt ]MANDO Adapt T212RD [ without draw bolt ]MANDO Adapt T812RD [ without draw bolt ]Jaw adapter RDTOROK manual chuck. Clamps gently or forcefullyTOROKsensitive manual clamping is possiblemanual actuation – a clamping cylinderis not requiredconcentric precision < 0.01 mm possibleminimal effects of inertia lossClamping elementsAdaptationsClamping headMANDO Adapt T211[ with draw bolt ]MANDO Adapt T212[ without draw bolt ]Jaw adapterB-Top3 jaw chuck. They all fit in one anotherB-Top3through-bore passage bushings orend-stop bushings that can be changed fromthe front Ø 62 mmfast jaw change with individual unlocking athigh change-over accuracy and suitable forthe »Reishauer« system, straight gear cuttinghigh degree of operator safety with minimumchange-over timeproven wedge rod mechanismClamping elementsAdaptationsJaws, different typesMANDO Adapt[ Mandrel-in-jaw-chuck ]SPANNTOP Adapt[ clamping headend-stop chuck]SPANNTOP Adapt M[ clamping headthrough-bore chuck]

Eccentric chuck. Concentric and eccentric machining in a single clamping set-upEccentric chuckinfinite eccentric adjustment via the C-axisconcentric and eccentric machining in asingleclamping set-upminimal effects of inertia lossClamping elementsClamping head RDChucks made of carbon fiber. Light, lighter, carbon fiberChucks made of carbon fibermade of carbon fiberas much as 70 % lighter than the standard versionIncreased productivity through faster acceleration/decelaration of the machine spindleparticularly user friendlyreduced energy costsClamping elementsClamping headAdaptationsJaw adapterMandrel MANDO T211. Efficient and economicalMANDO T211vibration dampening due to vulcanizedsegmented clamping bushingswork piece stabilization through axial drawforce applied against the work piece end-stopform-compensating segmented clampingbushings upon requestclamping range from Ø 20 – 120 mm withonly 5 mandrel sizesClamping elementsAdaptationsSB segmented clampingbushingSAD segmented clampingbushing [ for machining to size ]MANDREX cartridgeMandrel MANDO T212. Perfekte I.D. clampingMANDO T212vibration dampening due to vulcanizedsegmented clamping bushingswork piece stabilization through axial draw forceapplied against the work piece end-stopclamping without draw bolt, consequently idealfor blind boresclamping range from 8 – 120 mm withonly 8 mandrel sizesClamping elementsAdaptationsSB segmented clampingbushingSAD segmented clampingbushing [ for machining to size ]

NC vise UNOK. There‘s force behind itNC vise UNOKvery rigid, one-piece basic body, chuckingpossibilities base side, lateral, and verticalbasic body ground all-roundmoveable pull-back jaw, the work piece doesnot lift off while clampingrepeatability < 0.01 mm possiblemanual actuation, hydraulic high-pressuretransmission ratiopreliminary introduction of force is possibleClamping elementsJawsMultiple vise DUOK. The specialist for seriesMultiple vise DUOKvery rigid, basic body, chucking possibilitiesbase side, lateral, and verticalbasic body ground all-round3rd hand function facilitates accurate positioningof the work piecesrepeatability < 0.01 mm possiblemanual actuation, hydraulic high-pressuretransmission ratiopreliminary introduction of force is possibleClamping elementsJawsManual stationary chuck MANOK. Small but powerfulMANOKeasy set-upsensitive manual clamping is possibleideal for 5-sided machiningrepeatability < 0.01 mm possibleClamping elementsClamping headBild: Maschinenfabrik Berthold HermleManual stationary chuck MANOK plus. Incredibly versatileMANOK pluslateral clamping set-up possiblesensitive manual clamping is possibleideal for 5-sided machiningrepeatability < 0.01 mm possibleClamping elementsAdaptationsClamping headMANDO Adapt T211[ with draw bolt ]MANDO Adapt T212[ without draw bolt ]Jaw adapter

Mandrel actuation units ms/hs dock. Use MANDO segmented mandrels stationaryms / hs dockideal for 5-sided machiningclamping range from Ø 8 –120 mm withonly 8 mandrel sizesideal for short blind bores, since there areno draw boltsvibration dampening through rigid steel segmentsAdaptationsMANDO T211[ with draw bolt ]MANDO T212[ without draw bolt ]ZS-R-125[ Centric vise ]Stationary clamping devices made of carbon fiber. Less weight, a lot to offerStationary clamping devicesmade of carbon fiberas much as 70 % lighter than the standard versionparticularly user friendlymachine components are offloadedhigher usable work piece weight is possibleClamping elementsAdaptationsClamping headMANDO Adapt T211[ with draw bolt ]MANDO Adapt T212[ without draw bolt ]Jaw adaptercapteX. Clamping change in secondscapteX quick change-over systemclamping device change-over in 30 secondsrepeatability < 0.002 mm possibleup to 4.000 RPM possibleautomatic drawtube connectionlocking via only one central screwsuitable for any machinestandardization of the machineshop with one interface possibleAdaptation examplesSPANNTOP nova chuck+ clamping device adapterJaw chuck B-Top3+ clamping device adapterMANDO mandrel+ clamping device adaptercentroteX. Standardization of the machine shopcentroteX Schnellwechselsystemclamping device change-over 1.5 minutesrepeatability < 0.002 mm possiblemax. RPM possibleautomatic drawtube connectionstandardization of the machineshop with one interface possibleMachineadapterAdaptation examplesSPANNTOP nova chuck+ clamping device adapterJaw chuck B-Top3+ clamping device adapterChuck change-over with centroteX interfaceMANDO mandrel+ clamping device adapter