Cycling - Alge-Timing

CYCLING - Track CyclingTiming SystemALGE-TIMING can offer the complete technical equipment for carrying out track cycling events may they be large or small.This ranges from simple training systems to complete systems for major events.All accessories are also available e.g. starting machines, starting display boards with countdown and cabling solutions.The photofinish system OPTIc2 has already been presented on some previous pages. On the following pages we will givean overview of the devices developed especially for track cycling.On the following page you find a diagram of a complete track cycling system. Of course, ALGE-TIMING also equips smallervelodroms. Please contact your local ALGE representative for further information.www.alge-timing.com

T I M I N GT I M I N GALGE-TIMINGCYCLING - Track CyclingTiming SystemOPTIc2CameraTapeswitch ATS3Pursuit (green)StretchCycle StartmachineTapeswitchATS7IT 100 mGALGE-TIMINGALGE-TIMINGDisplayCyclestart ProABSV4/SMStartmicrophone SM8with Startgun STPTimy2Timy2 Terminal forCyclestart ProHeadsetHS2-2ETapeswitchATS7Start 200 mALGE-TIMINGALGE-TIMINGHeadsetHS2-2Display BoardCyclestart ProLap CounterD-LCDisplay Board D-LINE for CyclingSV4-SCDHomeCycle StartmachineTapeswitch ATS3Pursuit (red)Tapeswitch ATS7Finish SprintVelo-SoftwareTimingHeadsetHS2-2FOPTIc2CameraODB2OPTIc2CameraOPTIcDistribution BoxOCD2ODB2OPTIcDistribution BoxOCD2PC with MonitorPC forOPTIc2PC forOPTIc2DISPLAYManagerTiming Device TdC 80011GBit SwitchPC with Monitor123Videowall or Full Matrix LED Display BoardSpeaker ModulePress Information System1GBit-Switchwww.alge-timing.com

CYCLING - Track CyclingCycle StartCycleStart is a multi use system es pecially developed for track cycling. For all events with an electronic countdown(e.g. pursuit) it is used as start countdown. The display board counts down from 50 seconds to zero supported by acountdown horn. The CycleStart can be used as lap counter and backup timing system for all races.The CycleStart includes the complete connection boxes for the timing. This means that at all strategically importantplaces a distributor box is placed in order to connect timing devices, displays, etc. Since the cable lengths mayvary a lot depending on the track, the cables are not included in the system but ALGE can provide them in custommadelengths.ALGE-TIMING offers a CycleStart for mobile installation as well as for permanent installation.CycleStart M consisting of:2 x CycleStart display board CS-DB2 x tripod TRI128Terminal Timy2 XEPower Supply PS12A2 x pushbutton 023-02 for lap counterDistributor Central VELO-M-BDistributor RED VELO-M-ADistributor GREEN VELO-M-CDistributor Sprint VELO-M-DDistributor Start 200 m VELO-M-EDistributor Timing VELO-M-FCycleStart P consisting of:2 x CycleStart d isplay board CS-DB2 x tripod TRI128Terminal Timy2 XE2 x pushbutton 023-02 for lap counterDistributor Central with integrated chargerVELO-P-BDistributor RED VELO-P-ADistributor GREEN VELO-P-CDistributor Sprint VELO-P-DDistributor Start 200 m VELO-P-EDistributor Timing VELO-P-Fwww.alge-timing.com

T I M I N GT I M I N GCYCLING - Track CyclingCycle StartDisplay Board CS-DB:two electromagnetical digits, yellowon black ground, red-green light forcountdown and cycle identification,figure height 15 cm, max. readingdistance about 70 m, includingcountdown horn and powerpack(battery and charger)Tripod TRI128:with a maximum height of 128 cmController Timy2:to control the display board (countdownfunction and lap counter), as well as backuptimere.g. Distributor VELO-M-Ae.g. Distributor VELO-P-CTapeswitch ATS3Pursuit (grün)StretchCycle StartmachineDisplayCycleStart ProAStart Microphone SM8with Start GunT I M I N GBSV4/SMTerminal Timy2 forCycleStart ProETapeswitch ATS7Start 200 mCycle Start forTrack CyclingHeadsetHS2-2DisplayCycleStart ProSV4/SCDHomeCycle StartmachineTapeswitch ATS3Pursuit (rot)Tapeswitch ATS7Finish SprintFwww.alge-timing.com

CYCLING - Track CyclingTrack Cycling Startmachine ST-BSM1Variable adjustable pneumatic startmachine (with compressor)that meets the highest requirements for alllevels of track cycling:start output (banana sockets)start input (banana sockets)connection for compressormeter for compressed airpush button for back wheel brake - closingpush button for back wheel brake - openingpush button for saddle holder - closingpush button for saddle holder - openingpush button for back wheel stand2 x operation switchbrake for back wheelbrake for saddleback wheel standinternal 12V rechargeable batteryadjustable level for track steepnesswww.alge-timing.com

T I M I N GT I M I N GALGE-TIMINGTimy2CYCLING - Track CyclingTrack Cycling Startmachine ST-BSM1Operating ElementsSaddle HolderCompressorCycle is locked at saddle and at the back wheelas well as a stand stabilizer at the back wheelT I M I N GTiming Systemfor Track CyclingOPTIc2nCameraTapeswitch ATS3Pursuit (green)StretchCycle StartmachineTapeswitchATS7IT 100 mDisplayCyclestart ProAStartmicrophone SM8with StartgunGBSV4/SMTerminal Timy forCyclestart ProETapeswitchATS7Start 200 mVideowall or Fullmatrix LED ScoreboardHeadset Q34DisplayCyclestart ProDisplay Board D-xxxfor CyclingSV4/SCD21HomeCycle StartmachineTapeswitch ATS3Pursuit (red)Tapeswitch ATS7Finish SprintSPEAKER ModuleHeadsetHS2-2FOPTIc2nCameraOPTIc2nCamera1GBit SwitchTapeswitchSelectorODB2OPTI DistributionBox OCD2ODB2OPTI DistributionBox OCD23DISPLAYManagerVelo-SoftwareTIMINGPCforOPTIc2nPCforOPTIc2nPress Information System1GBit-SwitchPC with MonitorPC with MonitorTiming Device TdC 8001www.alge-timing.com

CYCLING - Mountain BikeDownhillThe start is effected by a photocell or a contact band. The startclock at the start makes sure that the starting intervals are adheredto. For triggering the photocell or contact band and for communication with the finish a cable adapter LA5 is recommended.At the finish a photocell stops the time of the timing device TdC 8001 and controls the display board.Headset HS2-22PhotocellAdapter LA5STARTPhotocell PR1a-R orTapeswitch ATS3ALGE-TIMINGStartclock ASC2PC withResultSoftwareDisplay Board GAZ4 or D-LINEHeadset HS2-2Photocell PR1a-RFINISHTiming Device TdC 8001Alle Computer im obigen System sind mit einem Netzwerk untereinander verbunden!www.alge-timing.com

CYCLING - Mountain BikeCross Country and SpeedMountain Bike - Cross Country:The start is effected by a start pistol.For counting the laps a lap counteris positioned at the finish line.At the finish a photocell stops thetime of the timing device TdC 8001and controls the recording of thephotofinish. A display boards showsthe running time.HeadsetHS2-2Startmicrophone SM8with StartgunSpeech AmplifierSV4/SMALGE-TIMINGLap CounterOPTIc2CameraDisplay Board GAZ4 or D-LINESTART and FINISHPhotocellPR1a-RPrinterPush Button023-10Headset HS2-2PC for PhotofinishOPTIc2Timing Device TdC 8001Mountain Bike - Speed:For measuring the speed two photocells arerequired. They have to be placed at exactlythe predetermined distance. The timing deviceTdC 8001 or Timy measures the accuratespeed and shows it on a display board.STARTPhotocellPR1a-RTkm/hDisplay Board GAZ4 or D-LINEPhotocellPR1a-RTFINISHTiming Device TdC 8001www.alge-timing.com

PHOTOFINISHOPTIc2nThe ALGE OPTIc2n is the next generation of the successful photofinish system OPTIc. The camera uses the latest CCD linescanning sensor technology. This allows using the camera even at bad light conditions. High recording speed with up to 3000lines per second and high resolution of up to 1360 pixel.The OPTIc2n is a computerized color photofinish system with integrated evaluation software. The color line scanning camerascans every movement at the finish line in true color (24 bit, 16.8 million colors) and stores the data on the hard disk of the computer.The stored picture can be displayed on the monitor or can be printed at any time.The main features of the ALGE OPTIc2n are:Best picture quality in all light conditions by modern line scanning sensor.Highest timing precision by Temperature Compensated Quartz Oscillator TCXO.Easy handling with Windows XP, Windows Vista or Windows 7.Unlimited recording time with suitable PC hardware.High resolution, 3000 lines per second and 1360 pixel.Recording speed is adjustable between 100 and 3000 lines per second.Vertical resolution is adjustable: 680, 768, 1024 or 1360 pixelEvaluation is possible even before all competitors reach the finish line.You can evaluate a finished race while another race has been started.It is possible to start a new race before the finished race is evaluated.The time of each evaluated competitor is recorded automatically into a flexible result list.Camera OPTIc2n for IEEE1394 connection (up to 10 m cable) or optical cable connection (long distance).The OPTIc2n allows connection with CAT5e cable (RJ45 plug). With a CAT7 cable you can bridge about 80 m. It needs atthe PC side an adapter RJ45-1394 or the ALGE Distribution Box OCD2.Possibility to use a desktop PC or notebook with IEEE 1394 (firewire) interface.C-Mount lens adapter as standard (on request Nikon lens adapter possible)C-Mount zoom lenses and motorzoom lenses are available.www.alge-timing.com

PHOTOFINISHOPTIc2nFor which sports is the OPTIc2n sensible?Track and FieldCyclingHorse RacesGreyhound RacesCross CountryBiathlonRowingCanoeingShort TrackInline SkatingMotor Sportany sport as backupwww.alge-timing.com

PHOTOFINISHOPTIc2nIntegrated EvaluationThe OPTIc2n includes three ways of transferring the timefrom the picture into the result list:Manual Identification:Mark the competitor in the result list. Move the time line with themouse to the point where you want to read the time and pressthe right mouse button. The time automatically moves to theselected competitor in the result list.Lane Identification:Mark all lanes before the race starts. For the results of an individualcompetitor, move the time line to the correct lane. Pressthe right mouse button and the time for that competitor is automaticallyrecorded in the result list.Start Number Identification:Move the time line to the point to where you want to time an individualcompetitor. Press the right mouse button. A small windowopens, where you have to input the ID number of the competitor.That time moves automatically into the result list.Result Lists• Start list• Result list sorted by rank• Result list sorted by lane• Result list sorted by start numberStartmicrophone SM8with StartgunFlexible Result Lists:• It is possible to select, name and sort headers and to selectthe length of the text field for the header.• The software can calculate the following headers:average speed, delta time, horse distance.• If a competitor has no time in the result list, it is possibleto select the reason for this in a pull down menu.• If you use the keyboard to input the time into the result listinstead of copying it from the picture, the time will be marked.HeadsetHS2-2Speech AmplifierSV4/SMOPTIc2for AthleticAnemometer WS2Terminal Timy2 XEHeadset HS2-2PCAnemometer WS2OPTIc2nCamera1 2 3 4 5 6 7 8Photocell RLS3cDisplay Board GAZ4 or D-LINEPrinterwww.alge-timing.com

Technical DataCamera OPTIc2nSensor:3 x 1360 pixel (RGB)Pixel Resolution: max 1360 pixel per laneNumber of Colours: 16.7 million colours or black/whiteScan Rate:100 to 3000 lines per secondRecording Time: unlimited; depends on PC hardwareLens:C-Mount lens adapter - option: Nikon lens adapterQuartz Frequency: TCXO 20,000 MHz (temperature compensated quartz oscillator)Measuring Range: 23 hours, 59 minutes, 59.999 secondsFrequency Deviation: Temperature: +/- 2.5 ppm at -10° to +70°C(+/- 0.009 seconds per hour)Ageing: +/- 1 ppm per yearFrequency Adjustment: +/- 0.1 ppm at 25°CConnections: 2 x start input (banana socket)1 x finish input (banana socket)2 x finish input (DIN socket)1 x display board (banana socket)1 x motor zoom1 x IEEE 1394a 6 pin1 x GOF (LC duplex glass optical fibre connector)1 x CAT5e cable with RJ45 plug1 x power supplyPower Supply: + 9 - 36 VDCTemperature Range: 0° to 50°CRequirements for IEEE 1394 interface for PC:Compatibility: IEEE 1394A or 1394B OHCI compatibleTransfer Rate: minimum 400 MBit per secondPHOTOFINISHOPTIc2nRequirements for PC (Desktop or Notebook):Operating System: Windows XP, Windows Vista or Windows 7Processor:Intel Pentium Dual Core (similar or better)Hard Disk:minimum 60 GB hard disk (the faster the better)Memory:minimum 1 GB RAMGraphic:minimum 32 MB Graphic RAMMonitor Resolution: minimum 1024 x 800, best with 1920 x 1200Interface:IEEE 1394A or 1394B OHCI compatible interfaceCamera OPTIc2nAccessories:ALGE-TIMING offers a wide range of accessories for the photofinish camera. Below we list only the most important ones.Please contact your local ALGE dealer for more information.Different Lenses for Camera: Wide range of zoom lenses (manually and electronically controlled) and fix lenses.IEEE1394 Camera Cables: Wide range of IEEE1394 cables (up to 10 m) and repeater cables (up to 30 m).Optical Cables:Wide range of optical cables and cable reels with optical cables.IEEE1394 Interfaces: Wide range of 1394 interfaces for desktop PC or notebook.Distribution Box OCD2: Connection box for OPTIc2 if the camera is not reachable or far from the PC operator.Tripod Triman:To mount the camera (maximum height 2.4 m, in addition a gearhead is necessary).Manual Gearhead 410: Three-dimensional gearhead to adjust the camera exactly to the finish line.Electronic Gearhead 410E: Electronically controlled three-dimensional gearhead to adjust the camera exactly to the finishline; no additional wiring necessary; controlled by the OPTIc2 software of the PC.Weather Protection Case: Protects the camera if used outside in bad weather.Battery Backup for Camera: Battery device BB1 with integrated 12 VDC battery and charger.www.alge-timing.com

Distribution BoxPHOTOFINISHDistribution Box OCD2If your photofinish camera is positioned far from the operator you can connect the external devices (e.g. start device,finish photocell) to the Distribution Box OCD2 next to the operator.Why do you need a Distribution Box OCD2:Synchronisation of up to three connected photofinish camerasConnection of external devices next to the operator and not at the cameraIntegrated converter for optical cable or network cable (CAT5e with RJ45)Integrated speech amplifier to connect a headset for communication between starter and timing operatorConnection of up to three independent input signals (start, IT, finish) for up to three different photofinish camerasIntegrated battery pack to run the OCD2 and photofinish camera (only with 6-pin IEEE1394) independently frommainsHeadsetHS2-1100 - 240 VACBattery BoxBB1PhotofinishOPTIc2nCamera for60 m TrackDisplay Board D-LINEALGE-TIMING100 - 240 VACBattery Box BB1PhotofinishOPTIc2nCamera for200 m TrackPhotocell RLS3cDistribution BoxOCD2OPTIc2OCD2readyopticallow batchargepowerAC-power100 - 240 VACNotebook for OPTIc2Track and FieldIndoor Stadium1 2 3 4 5 6 7 81 2 3 4 5 6 7 81 2 3 4 5 61Startmicrophone SM8with StartgunLap CounterDisplay BoardD-LINEALGE-TIMINGPhotocell RLS3cHeadset HS2-22Speech AmplifierSV4/SM1Startmicrophone SM8with StartgunHeadset HS2-22Speech AmplifierSV4/SM1 2 3 4 5 6www.alge-timing.com

PHOTOFINISHDistribution Box OCD2Technical DataQuartz Frequency: TCXO 20.000 MHz (temperature compensated quartzoscillator)Measuring Range: 23 hours, 59 min., 59.999 sec.Frequency Deviation: Temperature: +/- 2.5 ppm at -10 to +70°C(+/- 0.009 seconds per hour)Ageing: +/- 1 ppm per yearFrequency Adjustment : +/- 0.1 ppm at 25°CInternal Battery: lead battery 12 V / 2,2 AhPower Supply: +9 - 15 VDCTemperature Range: 0 to 50°CConnections: 3 x start input (banana socket)3 x finish input (banana socket)3 x finish input (DIN socket)2 x display boards (banana socket)1 x RS232 – DIN socket1 x Printer – DIN socket3 x Photocells – DIN socket1 x Headset – DIN socket1 x Windspeed WS21 x Camera – IEEE1394a 6 pin bilingual1 x Camera - GOF (LC duplex glass optical fiber)1 x Power Supply +9 - 15 VDC1 x Mains 100 – 240 VACALGE-TIMINGDisplay Board D-LINE or GAZ4PhotofinishCamera OPTIc2nTeledata TED-TXStartgatewithClosingContactTeledata TED-TXMirror forPhotofinishFinishSandPhotocellPR1a-dMirror forPhotofinishFinishGrassPhotocellPR1a-dOPTIc2Distribution BoxOCD2readyopticallow batchargepowerAC-powerTeledataTED-RXDistribution BoxOCD2StartgatewithClosingContactColor PrinterPC for Photofinish OPTIc2152Photofinish Systemfor Horse Racingwww.alge-timing.com

PHOTOFINISHOPTIc2 AccessoryYou can obtain from us a wide range of accessories for the photofinish system OPTIc2. For further accessories,that cannot be shown here, please contact us.Zoom Lens Z75:manual zoom lensC-Mount 2/3", 12,5 - 75 mm / F1.2Weather Protection WSC2for OPTIc2 Camera with lensesZ75, MZ75 and L8.5Motor Zoom MZ75:Control of focus, zoom and brightnessvia PCC-Mount 2/3", 12,5 - 75 mm / F1.8Gear Head 410Tridimensional mechanical gearhead to adjust the camera exactly atthe finish line.Motor Zoom MZ160R:Control of focus, zoom and brightnessvia PCC-Mount 2/3", 16 - 160 mm / F2.2Remote Control Gear Head 410-E:Tridimensional electronic gear headcontrolled via PC (no further cablingnecessary).Wide Angle Lens L8.5:C-Mount / 2/3", 8,5 mm / F1.3C-Mount Adapter Z-000402-1:Adapter for Photofinish Systemfrom camera (M42x1) to C-mountlenses with fine adjustment for focaldistanceTripod for OPTIc2 Camera:Standard tripod Triman with a maximumheight of 2.4 m.On request tripods up to a height of3.8 m.F-Mount Adapter F-MOUNT:Adapter for photofinish Systemfrom camera (M42x1 to F-mountlenses (Nikon).Battery Backup BB1Battery power supply for camera(integrated 12 VDC battery withmains adapter).Radial Polarising Filter:On demand we can supply polarisingfilters to weaken reflections(e.g. from water).www.alge-timing.com

PHOTOFINISHOPTIc2 AccessoryCamera Cables and Cable Reels:If the camera is situated far fromthe user a mains and/or optical cableis required. ALGE-TIMING offerscable and/or cables on reels in differentlengths.IEEE 1394 Adapter AB-CON:Adapter for IEEE1394 cable from6-pin plug to 4-pin plug.IEEE1394 Interface for PC:1394PCI: PCI card with IEEE 1394connections for desktop PC1394PCIe: PCI express card withIEEE1394 connections fordesktop PC1394PC: PC card (PCMCIA or Card-Bus) with IEEE1394 connectionsfor notebook1394EXP: Express card with IEEE1394 connections for notebookIEEE1394 Cables:Large assortment of firewire cableswith a length of up to 10 m and with4-, 6-, or 9-pin plugs.Choice of cables:AA-2 2 m cable lengthAA-4.5 4.5 m cable lengthAA-10 10 m cable lengthAB-2 2 m cable lengthAB-4.5 4.5 m cable lengthAB-10 10 m cable lengthAC-2 2 m cable lengthAC-4.5 4.5 m cable lengthAC-10 10 m cable lengthCC-2 2 m cable lengthCC-4.5 4.5 m cable lengthFibre Optics Adapter GLAS1394:Adapter from firewire to fibre opticswith mains adapter.Network Adapter RJ45-1394:Adapter from firewire to Network cablewith RJ45 plugs (CAT5).ALGE-CODEAA-AB-AC-FUNCTION6 to 6 pinIEEE1394amax. 400 mBit/s6 to 4 pinIEEE1394amax. 400 mBit/sno power supply6 to 9 pinIEEE1394bmax. 400 mBit/sPICTURECC-9 to 9 pinIEEE1394bmax. 800 mBit/swww.alge-timing.com

TIMING DEVICESTdC 8001What is so special about the TdC 8001?Racing into the FutureFinally, the answer to your dreams. TheTimedata Computer TdC 8001 is one ofthe most rugged and weather resistantprinting timers ever produced. Imaginehaving to time a race sitting in a tent duringany type of bad weather. The TdC8001 can take it! The extremely accurateTCXO quartz along with hardened circuitryallows full operation from -25°C to 50°C(-10°F to 122°F). Specially designed LCDdisplays for running time and data editingare visible in all light levels and work instantly.The case with integrated recharge-Useful features include:Integrated software for all types of populartimed sportsTotal printer control, continued timingwhile printing results, printer buffer activeso you do not lose data whilechanging paperMemory for up to 10000 splits with competitionnumbers up to 9999Four separate races can be run beforehaving to clear the memoryMultiple heats can be run within eachraceResults can be produced for up to 40different age and sex classes racingtogetherable battery pack is made of abrasion resistantmaterials.ALGE’s leadership in the sports timing worldis well established. The TdC 8001 is theresult of constant feedback from all levelsof sports. Our TdC 4000 series has longsince handed over the lead to a most worthysuccessor. Look about your venue. Younever have to worry if you invest in the TdC8001 and matching accessories.Computer interface for an easy transfer ofnet or reference times to custom-made oruser created data basesDisplay interface for use with all types ofALGE displays or message centers andalso ready for high speed wireless transmissionIntegrated clock with user selectable timeof daywww.alge-timing.com

TIMING DEVICESTdC 8001ALGE TIMINGTdC 8001ENG V 03.51Program 1: V01.72SPLITWork on:Race 1Heat 1Precision: 1/100 sTiming:DIFFERENCEStartmode:SINGLE STARTChannels on:0,1,2,3,4,5,6,7,8,9Synchrontime:= 09:00:000001 ST 9:46:02.8702FT 9:47:21.4133RT 1:18.540002 ST 9:46:02.8618FT 9:47:31.2779RT 1:21.72Heat 2Precision: 1/100 sTiming:DIFFERENZStartmode:BIBO: 150001 ST 10:48:16.1121FT 10:49:27.6383RT 1:11.520002 ST 10:48:24.7473FT 10:49:35.0293RT 1:10.28MT 1:21.29TT 2:31.57Classement:ALLTOTAL TIMEStartclock ASC2TimePS12HeadsetHS2-2LED Matrix Display Board D-RTNMDisplay Board GAZ4HeadsetHS2-2Bib + RankPower Supply100 -240 VTdC 8001STARTStartgateSTSnM1SPhotocell PR1a-RIntermediate TimePhotocell PR1aFINISH1.0001 RT 1:11.52MT 1:18.54TT 2:30.062.0002 RT 1:10.28MT 1:21.29TT 2:31.57SPLIT:Measures intermediate and run timesStart channel, eight intermediate channels, finish channelSelectable calculated precision from 1/1000 up to 1 sec.Up to 256 heats (runs)Individual, group or mass startTime of day or absolute timingUp to 9999 competitors on course at onceMultiple result possibilitiesRecommended for: alpine skiing, cross- country skiing, mountain bike, biathlon, whitewatercanoeing, motor sports etc.www.alge-timing.com

PARALLEL SLALOMSTARTParallel StartgateTIMING DEVICESParallel Slalom with finishing difference only:Red and blue course identificationTime difference between both coursesRecommended for: alpine skiing and snowboardingParallel Slalom with net time and difference time:Simultaneous start for both coursesRun time for both coursesTime difference between both coursesRed and blue course identificationTotal time after switching courseTotal time difference after switching courseRecommended for: alpine skiing, snowboardingSTARTParallel StartgateTdC 8001Universal genius - timing examplesEQUESTRIAN:Includes software for all FEI showjumping events:Standard show jumpingStandard show jumping with two runsTime jumpingCompetition in two phasesAmerican jump-offStandard jumping and time jumpingTeam jumpingCarriage drivingetc.Example: Printout of Standard Show Jumping A1Countdown StartStart at 13.92 of CountdownStart Time (Time of Day)4 Penalty PointsTimeout StartTimeout Run Time6 Penalty SecondsEnd of Timeout4 Penalty PointsFinish Time (Time of Day)Run TimeHeadset HS2-2Speech AmplifierSV4-SPenalty SecondsPenalty Points for TimePenalty Points on CourseTotal Run TimeTotal Penalty PointsPS12Power Supply100 -240 VHeadsetHS2-2Photocell PR1aFINISHALGE-TIMINGALGE-TIMINGPhotocell PR1aFINISHTeledata TED-TX10StartPhotocell PR1a-RTor PR1a-dTTeledata TED-TX10Teledata TED-TX10FinishPhotocell PR1a-RTor PR1a-dTFinish Jump OffPhotocell PR1a-RT or PR1a-dTmin. sec.1/100Run Time blueALGE-TIMINGmin. sec.1/100Run Time redmin. sec.1/100Time DifferenceDisplay Boards GAZ4ALGE-TIMINGTdC 8001DUAL TIMER:Timing of two courses simultaneouslyMeasuring of intermediate and run timesCalculation of total time after reversal of coursesSeparate or combined startOnly one racer on each courseSelectable calculated precision from 1/1000 - 1 sec.Results for each course individual or combinedRecommended for: alpine skiing, snowboardingTeledata TED-RX129-06Start-Stop-Switch129-06TimeoutPush ButtonTdC 8001Speaker DLALGE-TIMINGALGE-TIMINGLED-Display Board D-LINEwww.alge-timing.com

TIMING DEVICESTdC 8001SPEED:Adjustable measuring distance from 1 to 9999 meterDisplay and printout in km/h, m/s and mphBidirectional trapRecommended for: motor sports, skiing, ski jumping, cyclingSPEED SKIING:Fixed 100 m trap lengthDisplay and printout in km/h onlyDisplay and printout of start, finish and run timeRankingDOG AGILITY:The software includes the following programs for agilityDog AgilityGamblerSPEED SKATING:Automatic lane changeShows on two display boards both times of competitorsSTREET CYCLING:Measures the winning timeCalculation of the average speed of the winnerShows the time difference between winner and othersCARVING:Countdown from the selected maximum course timeHorn at zeroAfter zero the time is counted upSelectable precision from 1/1000 up to 1 sec.Individual, group or mass startTime of day or absolute timingMeasuring range: 23 hours, 59 minutes, 59.9999 secondsTime reference: TCXO 11.520 MHz (temperature compensated crystaloscillator)Accuracy: temperature range from -25 to +50°C: +/- 2,5 ppm (+/-0,009s/h.)Ageing:+/- 1 ppm per yearFrequency adjustment: +/- 0,1 ppm at 25°CTemperature Operative Timing Range: -25 to 50°C (-10°F to 122°F)Electronic: most modern energy-saving C-MOS technology with 80C167microprocessorMemory: about 2 x 10,000 times with start numbers, keeps data whenswitched off by internal rechargeable batteryDisplay:start display (1): numeric liquid crystal display, 8 digits, figure height 12.7mmfinish display (5): numeric liquid crystal display, 8 digits, figure height12.7mmfinish display (6): numeric liquid crystal display, 8 digits, figure height12.7mminfo display (7): alphanumeric liquid crystal display, 4 x 40 characters, figureheight 4.8 mmOperating elements:On-/Off switch (g), start keyboard (12) with 15 keys,function keyboard (9) with 15 keys, finish keyboard (8) with 15 keysTechnical DataPower Supply: internal: NiCd rechargeable battery 7.2 V / 4.5 Aexternal: 230 VAC (alternative 115 VAC) with chargerPower Consumption:no external devices from the internal NiCd battery: about 80 mAwhen printing: about 500 mACharging Supply: +11 to 16 VDCImpulse Length: Input resistance 10 kÙ against +5V, triggering with

TIMING DEVICESTimy2ALGE Timy2 is of a compact design, equipped with high-quality technologyand unique for timing.The exterior of the Timy2 can hardly be distinguished from that ofthe previous model Timy. However, the interior has been completelyremodelled and updated to the latest technology: same housing,same keypad, improved display with backlight. The processor performancehas been doubled and the memory has twice the capacity.The major advantage of the Timy2 is, for certain, the low power consumptionthat triples the operating time with batteries, compared tothe Timy. Thus working with a battery pack at 20°C and three printedlines per minute is possible for up to 47 hours. Low power consumptionin spite of doubled processor performance in connection with ahigh-capacity NiMH battery pack is responsible for this progress.The new battery pack also offers advantages when operating attemperatures below freezing. Even at –20°C and three printed linesper minute the battery remains its high efficiency for up to 31 hours.It is needless to say that we kept the ergonomic and most reliabledesign. Despite the handy dimensions the Timy2 has a large andeasy to operate silicone keypad. In all weather conditions, evenwearing gloves, using the keypad does not cause any problemswhatsoever. The Timy2 PXE has an integrated printer that recordsthe complete competition.As a matter of course the Timy2 features the necessary interfacesfor communicating with external devices. Integrated in the device isan interface for a scoreboard, an RS232 for data exchange with acomputer, an RS485 for a network of timing devices as well as afuture proof USB interface.The memory of the Timy2 is generously dimensioned. It is capableof saving up to 30,000 times. All times recorded in the memory canat any time be displayed or send via RS232 or USB interface to acomputer.Display:The Timy2 has a monochrome LCD graphic display with 128 x 64 pixel andbacklight. With this, displaying up to 8 lines of text is possible. Differentcharacter sizes and also graphic symbols for easier operation can be displayed.The display has an extended temperature range for use in extremeweather conditions (e. g. winter sports).Keypad:In spite of the handy measurements, the Timy2 has a large and well operablesilicon keypad with 26 buttons. Even with gloves the Timy2 can easilybe operated.Accuracy:The Timy2 works on a time of day basis and records it with an accuracy ofth1/10,000 second. That means that calculated net times of a precision ofth1/1000 are exactly calculated. Highest accuracy at any temperature isguaranteed by a temperature compensated quartz.Printer:The Timy2 PXE has an integrated thermal printer. This silent and extremelyfast printer allows an easy and straightforward paper change. The feedroller is fixed to the printer cover and therefore saves oneself the tediousthreading of the paper.Memory:Memory of up to 30,000 times including ID number and channel information.The software is on a FLASH memory which allows an upgrade of thesoftware by internet from the PC.Case:Great attention has been placed to ergonomics and stability. The aim of thedevelopers was to produce a timer that has all advantages of modern technologyin a compact, handy but rugged case. This design has been chosenso that it is usable as a handheld and desktop device.Connections:Regarding the wide range of possible connections with external devices,the Timy2 offers unequaled opportunities in its class and size. E.g. it ispossible to connect several devices by the RS485 interface to work as anetwork.Software:There is a great number of programs for the Timy2. The Timy2 is able tocover the entire spectrum for time measurement starting from a hand timerup to the main timer at major events.www.alge-timing.com

22TIMING DEVICESTimy2Timy2 SoftwareBackup: timer to measure time of day (e.g. backup or referencetimer for PC)Stopwatch: universal timing program that is able to time morethan one run (net time/total time)TrackTimer: timing for events which have lanes (e.g. athletics,swimming)LapTimer: timing program with split and sequential timePC-Timer: professional timer (time of day) to work with a PCTraining Light: universal training software with intermediate timesand one racer on courseTraining REF: training software with intermediate times and morethan one racer on courseSpeed: speed measurement in km/h, m/s, or mphCommander: terminal to control ALGE display boardsTerminal: terminal for judges, e.g. ski jumping, figure skating,diving, synchronized swimmingCycleStart: start control, lap counting and backup timing for pursuitcyclingWindspeed: to measure the windspeed for athletics with a connectedanemometer WS2Parallel-Diff: timing program for parallel slalomSpeed-Climbing: timing program for speed climbingTimeout: timing program with timeout function (e.g. show jumping)Swim Trainer: training program for swimmingJumping: training program for jumping exercisesALGE-TIMINGALGE-TIMINGTTTimy2 XEThe Timy2 XE is a timer without printer. It has a temperaturecompensated quartz oscillator for time measurementwith the highest precision and an extended temperaturerange for operational use down to –20°C(-4°F).Timy2 PXEThe Timy2 PXE is a timer with integrated printer. It hasa temperature compensated quartz oscillator for timemeasurement with the highest precision and an extendedtemperature range for operational use down to–20°C (-4° F).Paper RollThermal PrinterPrinter HoodLCD Graphic DisplaySilicone KeypadTechnical DataProcessor: Siemens C161 with 3,3 V technologyCrystal Frequency: 12.8 MHz with TCXOTime Resolution: 1/10,000 sProgram Memory: FLASH memory with 16 MBitData Memory: RAM with 4 MBit (about 30,000 times)Display:monochrome LCD graphic display with backlight,128 x 64 pixel, extended temperature rangeKeyboard: silicone keyboard, 26 keysConnections: 1 x DIN socket for photocell (7)1 x banana socket pair – start input (5)1 x banana socket pair - finish input (6)1 x banana socket pair – display board (4)1 x D-Sub 25 pin (3)· 9 timing channels· RS232 (PC connection)· display board· RS485 (network)· power supply (8–24 VDC in/out)1 x USB (1)1 x power supply (8 - 24 VDC in) (2)Channel Extension:Power Supply:per extension 8 channels, max. 99 channelsInternal:NM-Timy2rechargeable NiMH battery pack forTimy2 with printer, 2 Ah6 x AA-Alkaline 6 x 2 Ah (only for Timy 2 XE)External:Power Supply PS12A: 12 V battery or 9-15 VDCPower Consumption: data given at 20°C (68 F)Alkaline: without printer about 100 hoursNM-Timy2: without printer about 60 hoursNC-Timy2: with printer about 47 hoursCharging Duration: about 14 hoursPrinter:graphic thermal printer, max. 5 lines per sec.Temperature Range: -20 to 60°C (-4 to 140 F)Measurements: Timy2 XE: 204 x 91 x 50 mmTimy2 PXE: 307 x 91 x 65 mmWeight: Timy2 XE: 450 g (no battery)Timy2 PXE: 650 g (no battery and paper)1234 5 6 7www.alge-timing.com

TIMING DEVICESTimer S4Universal GeniusSimple as always, rugged as no other!The Timer S4 is very popular because of the simple operation(e.g. if different people have to work with it). Professionalslike the S4 as it has many impulse channels and aRS232c interface to communicate with a PC.3 independent clocks can be accessed for either 3 independentcourses or 3 individual competitors18 channel timing deviceMemory for 8000 times with consecutive numbers and channelidentificationIndividually adjustable delay time for start and finish impulsechannelsIntegrated speech amplifier for speech connection betweenstart and finish by headset using the 2 wire impulse cableOutput to control ALGE display boardsOutput to connect a printer (e.g. Printer P5)RS232c interface to communicate with a results PCLarge LCD display with a figure height of 13 mmThe operation is independent from mains possible throughintegrated battery (Alkaline or rechargeable battery)Adjustable precision (1/10, 1/100 or 1/1000 seconds )The Timer S4 has a large variety of programs toAccessories:We can offer a lot of accessories for the Timer S4.use it universally:Split:Net timing with a maximum of three competitors on course.Sequential:Lap timing with a maximum of three competitors on course.Parallel Slalom:Program for time difference or time difference and run times.3-Parcours Timer:Start and finish time for three independent courses.18-channel timer with net time:Universal timing program designed for online use with a PC.Allows the recording of a start for individual or mass events,intermediates and finish, all with channel identification, continuousID number and net time.18-channel timer with time of day and net time:Enhanced version of the program listed above with the additionof time of day reference time for every time split recorded.Also allows the use of split and sequential or timeout features.18-channel timer with time of day and countdown:Enhanced version of the program listed above with the replacementof net timing by countdown capability. Also allowsusage of timeout feature.Automatic:Ideal training program enables the user to select the number oftiming points that will be received, displayed and reset withoutthe need for an operator.Additional programs:Show jumping, dog agility, swimming, speed measuringPower Supply PS12Printer P5MultiChannel MC18StartgatesPhotocellsPush ButtonDisplay BoardsHeadsetsTeledata TEDCarrying Case for transportetc.www.alge-timing.com

TIMING DEVICESTimer S4Technical DataMeasuring Range:Crystal Frequency:23 hours, 59 minutes, 59.999 secondsTCXO 9.216 MHz (temperature compensated quartz oscillator)Accuracy: Within -30°C to +75°C: - 2.5 ppm (+/-0,009 seconds per hour)Ageing:+/- 1 ppm per yearFrequency adjustment: +/- 0,1 ppm at +25°CTemperature Range: -25 to 50°CMemory:Display:Electronic:Power Consumption:8000 times with consecutive ID numbers and channel identificationLCD numeric display with 8 characters, figure height 12.7 mmCMOS-TechnologyWithout external devices from internal battery about 60 mAImpulse Input Channels:18 impulse input channelsInput resistance 10 kagainst +5VTriggered with < 1V (down trigger)Hysteresis about 2 VOutput Channels:Speech Amplifier:5VDC stabilized, total maximum 120 mACommunication possible withchannels C0, C1, C2, C3, C6 and C9Speaker Output: For 8 speaker, Umax= 24 VppOperation Elements: 1 on/off switch (23)1 push button "start/stop" red (5)1 push button "next" yellow (6)1 toggle switch (A-, B- and C-timer) (4)1 toggle switch (program, line test,delay time) (7)Casing:Weight:Black anodized aluminium case withintegrated battery boxHandle for carrying and countertopHeight adjustmentW x H x D = 226 x 95 x 162 mm2.2 kg (including batteries)1 2 3108 9 114 5 6 712 13 14 15 161.......Display, 8 numerical digits2.......LED lamp for external power supply3.......Meter to show battery power and photocell condition4.......Toggle switch with 3 positions5.......Start/Stop button6.......Next button7.......Toggle switch with 3 positions8.......DIN socket for headset9.......DIN socket A (e.g. for photocell)10......Socket D-Sub 25 pin with all 18 channels11......DIN socket B12......DIN socket C13......DIN socket A´14......DIN socket for display board15......DIN socket RS 232c (e.g. for PC)16......DIN socket for external printer17......Volume for headset18......Input channel c0 (Start)19......Input channel c320......Input channel c621......Input channel c922......DIN socket for external speaker23......On/Off switch17 18 19 20 21 22 23www.alge-timing.com

START DEVICESStartclock ASC2the second generation in LED technologyThe major advantages of the Startclock ASC2:Nomechanical clockLarge, digital display with countdown timeCountdown light in red, yellow and greenFacts about the Startclock ASC2:LED technologyShows the time of day (hours, min. and sec.), green LEDFigure height of time of day digits is 5.5 cmShows the countdown with three digits in minutes and seconds,red LEDFigure height of countdown digits is 7 cmStart light with red, yellow and greenIntegrated speaker with volume regulationRS232 interface to connect a PC or printer (parametersof ASC2 can be adjusted by computer)integrated lead rechargeable battery for operation independentfrom mains supplystart input (banana socket)sync. input or countdown start (banana socket)potential free impulse output (banana socket)output for external speakerexternal power supply (12 VDC or 100-240 VAC)A.......Red start lightB.......Yellow start lightC.......Green start lightD.......Countdown clock with adjustablestart intervalsE.......Time of day clock withhours, minutes and secondsTechnical data1 .......Green push button2 .......Black push button3 .......Start input (e.g. startgate for skiing)4 .......Connector for start interval adjustment5 .......RS232 interface6 .......Start output7 .......Socket to connect external speaker8 .......External power connection (12 - 35VDC)9 .......Volume for speaker10 .....Countdown speaker11 .....Battery condition and charging LED12 .....Mains connector (100-240VAC)13 .....On / Off switch14 .....Fuse 1.0 A for power supplyUnit of Measurement: 1/1000 secondsMeasuring Range: 23 hours, 59 minutes, 59.999 secondsAccuracy: +/- 2.5 ppm (+/- 0,009 second per hour) between –20°C and +30°C (-4°F and 90° F)Time Base:temperature compensated real time clockDisplay:extra bright LED for outdoor use, brightness adjustable8-digit LED display, figure height 55 mm (2.16”), to show time of day3-digit LED display, figure height 70 mm (2.75”), to show the countdownstart light with 3 LED clusters in red, yellow and green, each 30 mm (1.18”) diameterTemperature Range: -25°C to +65°C (-13 F to 149 F)Power Supply:integrated powerpack (rechargeable battery (12 VDC, 7 Ah) and charger orexternal battery (12 - 35 VDC) or mains (100 - 240 VAC)Operating time:about 7 hours with one countdown per minute at 20°C in standard mode from internal batteryCase:anodized aluminium with cover and suspension flaps, 3/8" thread for tripod (tripod not included)Dimensions: W x H x D = 380 x 300 x 110 mm (14.96" x 11.81" x 4.33")Weight:6.4 kg (14.1 lbs.)www.alge-timing.com

CSTART DEVICESStartbeep STB1Microprocessor controlled acoustical starting commandtransmitter:Universal, low in price, rugged and handy!9 programmed start intervalsselectable with a multiple contact switch(10 / 15 / 20 / 30 / 40 / 45 / 60 / 90 / 150 seconds)2 freely programmable start intervals between 6 sec. and 99 min. 59 sec.,selectable by a multiple contact switchCountdown triggering also by internal or external key.Countdown triggering with or without standby signal (10 sec. before start)With the operation mode “Hupe” (horn) the startbeep can be used as a substitutefor the startpistol. Triggering by internal or external key.Synchronizable with other timing devicesStart output, potential-free closed contact (i.e. for triggering a timing device)88Technical DataABCALGEALGE Startbeep STB10 power off1 10 sec.2 15 sec.3 20 sec.4 30 sec.5 40 sec.6 45 sec.7 1.0 min.8 1.5 min9 2.5 minA time AB time BC set min.D set sec.E horn210FE3DPress button + power onD456 7 8 9 A BE205Electronics: μP-controlled in CMOS techniqueQuartz frequency: 4,608 MhzOperation temperature: -25 until + 45°CPowersupply: 9V alkaline battery (alternatively 9VNiCd battery)or external 12V batteryConnections: A = potential free closed contact forsynchronous triggering(starting)of a timing deviceB = external keyC = external supplyD = On/Off functionE = internal keyEcho transducer: horn loudspeaker, rotatableHousing:Polyamide, glass fortified(Impact strength)Fastening:chain fastening for mounting ona post etc.Weight:1 kgDimensions: 132 x 205 x 88 mmOperation time with alkaline battery at 30 sec. start interval:Without warning signal: 80 hoursWith warning signal: 10 hours132www.alge-timing.com

IMPULSE DEVICESPhotocell PR1aThe photocell PR1a is a masterpiece of precision and power with the smallest possible dimensions.The transmitter of the photocell sends a modulated infrared beam. The receiver checks the infrared beam and makes an impulsefor each interruption.To use the photocell universally it is possible to switch between three different functions: Reflection Photocell, PhotocellTransmitter and Photocell Receiver.Photocell PR1a:Impulse accuracy of up to 1/10,000 secondsDifferent functions with one photocell:Refection Photocell with ReflectorSeparate transmitter unit and receiver unit for long distance useLong distance rangeReflection Photocell about 25 mThrough-Beam Photocell over 150 m (500 feet)Variable power supply for the photocellBattery operationPower supply from ALGE timing deviceExternal power supply from 4 to 18 VDCBattery indication with LED (green, yellow, red)Indication of photocell adjustment with LED (green, yellow, red)Synchronisation of two photocells (main and backup) to prevent interferenceAdjustment of delay time (20 ms to 2 seconds (factory adjustment = 20 ms)Photocell PR1A withextendable cover to protect thelenses from rain or snow!Types of Photocells:Reflection Photocell PR1a-R:If one photocell is used with a reflector we call it a Reflection Photocell. The functionof the reflector is like a mirror, which reflects the beam sent from the transmitterback to the receiver.Photocell range: about 25 m (80 ft)Photocell set: 1 x PR1a, 1 x PR1a-Ref, 2 x BBG, 1 x 001-10 (10 m/33 ft)Reflection Photocell PR1a-RT:Same as PR1a-R but supplied with tripod (instead of fastening bracket BBG) and30 m (100 ft) photocell cable.Photocell range: about 25 m (80 ft)Photocell set: 1 x PR1a, 1 x PR1a-Ref, 2 x TRI128, 1 x 001-30 (30 m/100 ft)Reflection PhotocellThrough-Beam Photocell PR1a-d:The PR1a can be used either as TX or RX unit. It sends an infrared beam from onePR1a set as transmitter to another PR1a set as receiver.Photocell range: over 150 m (500 ft)Photocell set: 2 x PR1a, 2 x BBG, 1 x 001-10 (10 m/33 ft)Through-Beam Photocell PR1a-dT:Same as PR1a-d but supplied with tripod (instead of fastening console BBG) and30 m (100 ft) photocell cable.Photocell range: over 150 m (500 ft)Photocell set: 2 x PR1a, 2 x TRI128, 1 x 001-30 (30 m/100 ft)Through-beam photocellTechnical Data:Range with Reflector: 0.5 to 25 meterRange with Transmitter and Receiver: 0 to over 100 meterImpulse Output:NPN transistor, open collector, active lowReaction Time:300 μs, 1 ms fix adjustedImpulse Length:20 to 2000 ms (adjustable delay time)Measurements PR1A (without swivel head): about 118 x 87 x 44 mmWeight PR1A:about 0.3 kgWeight PR1a-Ref:about 0.2 kgSwitches:On/Off switch for batteryThree position switch for modes (Norm,TX, RX)Power Supply:from ALGE timer: 5 VDC stabilizedexternal power supply: 4 - 18 VDCinternal battery: 2 x AA-BatteryPower Consumption: from battery with 2,5 VDC: 20 - 46 mAfrom timing device 5 Vstab: 9 - 20 mAOperating hours with internal batteries: measured at a temperatureof 22°C (72F), with 1 impulse per minutealkaline AA batteries: 77 hoursNiCd AA rechargeable batt.: 70 hourswww.alge-timing.com

IMPULSE DEVICESPhotocells and AccessoryTriple Photocell RLS3:The triple photocell consists of three photocells that are integrated in one casing ontop of each other.Operating distance 2 to 15 mExternal power supply possibleIncluding transmitting-receiving unit, reflector, two tripods and 30 m cable.Reversible between the following modes of operation:Photocell Area: Used for athletics. Only if all three photocells are triggered at thesame time an impulse is produced. This prevents that the photocell is triggered byarms or legs (only triggered by body). Therefore, quite an accurate „inofficial“ winnertime is obtained. This photocell is very important when a display board is used.Single Photocell Use: All three photocells work independently, this means the firstthat is triggered produces a timing impulse (e. g. for Dog Agility)Photocell PWR:The photocell PWR has been developed for training courses and works without reflector.The triggering is effected by reflection of the infrared light of the object thattriggers the photocell.Maximum triggering distance 2.5 mThe triggering distance is adjustableVery small dimensionsIncludes photocell, swivel head and 10 m cablePhotocell Adapter LA5:Ideal for photocells that are connected at a large distance from the timing device(e.g. interim time).Internal batteries for power supply of the photocellIntegrated speech amplifier for communication with timekeeperDiverse operating modes, e.g. to activate the photocell by manual switch if manynon-participants pass the photocellMounting Bracket BBG:for fastening the photocells at polesMounting Bracket B-S1small bracket to screw the photocell or reflector to a wall or on a stakewww.alge-timing.com

ACCESSORIESOf course, you can obtain the adequate accessories for all devices from us. We would be pleased to advise you on what kind ofaccessories you require for your purposes. Below you will find a choice of our large assortment of accessories.Headset HS2-2headset with double-sided earphones and one microphone; recommended for outdoorand/or for high surrounding sound levelHeadset HS2-1:headset with single-sided earphone and one microphone, recommended for indoor and/orlow surrounding sound levelSpeech Amplifier SV4-S:with two connections for two-core connection wire (banana plugs), connection for headset,volume control and switch and/or push-button for microphoneSpeech Amplifier SV4/SM:with connection for two-core connection wire (banana plugs), connection for headset, connectionfor start microphone, volume control and switch and/or push-button for microphoneMultichannel MC9:channel extension for Timy2 with 9 banana socket pairs (impulse channel 0, 1, 2,3, 4, 5, 6, 7 and 8) and RS232 / RS485 socketTimy Docking Station TIDO:extension for Timy2 with integrated speech amplifier and the following connections:4 x DIN sockets for photocells1 x Multiport socket2 x DIN socket for RS2321 x DIN socket for speech amplifier9 x banana socket pairs (impulse channel 0, 1, 2, 3, 4, 5, 6, 7 and 8)GPS Receiver:for exact synchronisation of timing devices (e.g. for Timy2 and startclock ASC2)Adapter USB-RS232I:This adapter makes an optical isolation between the PC and the timing device. Thisis needed if you have a disturbing noise in the speech communication as soon asyou connect the PC to the timing device. Further it allows you to connect a timingdevice with RS232 interface with a PC with USB interface.www.alge-timing.com

ACCESSORIESPrinter P5:thermal printer with large temperature range (-20° to 50°C); supplied with differentplugs e.g. for Timer S4, Timy2 XE or startclock ASC2.Power Supply:several power supplies applicable for each timing devicee.g. PS12 (for TdC 8001, TdC 8000, Timer S4)PS12A (for Timy2, OPTIc2)Cable:We stock a large assortment of adequate cables in different lengths for the ALGE-TIMINGdevices.Cable Reels:We stock diverse cable reels in different lengths for each device, e.g. for the start connectionor data connection for display boards with two-core steel cable (extra strong militaryversion).KT120: 150m field telephone wireKT150: 150m field telephone wireKT300: 150m field telephone wireKt500: 500m field telephone wireTripods:tripods in diverse sizese.g. TRI128 (maximum height 128cm, see picture)TRIMAN (maximum height 240cm)Carrying Cases:for all devices with the fitting insert, for safe transport of the timing devices; customermade inserts possible; for transport of the devices on the ski slope, we also offer abackpackTiming Backpack ATBP:ideal for the transport of the devices (e.g. on the skiing slope); high quality backpackwith special compartments for storing the timing accessories; well padded back areaand carrying straps.Carrying Bags for Display Boards:carrying bags for display boards of the GAZ4 and/or D-LINE seriesGTT15: for display boards with 15 cm figure height and 6 digit casingGTT25: for display boards with 25 cm figure height and 6 digit casingwww.alge-timing.com

ACCESSORYTeledata TEDImpulse Transmission: Save as never beforeThe impulses (start or stop impulses) are transformed by a wireless transmitter TED-TX into a data package, provided with asafety code and transmitted to the receiver TED-RX. After having checked the safety code, the receiver transmits the impulseto a timing device with an accurate, reproducible delay of 0.1 seconds.StartFinishPhotocellTED-TXTED-RXTiming DeviceALGE Impulse Transmitter:Photocell PR1a or RLS1 seriesPhotocell RLS3Startmicrophone SM8Startclock ASC2Startbeep STB1TapeswitchTouchpad TPPush ButtonClosing ContactALGE Impulse Receiver:TdC 8001TdC 8000TdC 4000TIMER S4TIMER S3Timy or Timy2COMETPhotofinish OPTIStartclock ASC1StartgateStartTED-TX TED-RX Timing DeviceFinishThe Standard Version:Is able to receive two different timing channels. With the accessory RX-C10, up to 10 different channelsare available.The Safety Package of the Wireless Transmitting System ALGE TeledataTED:Protection against false impulses:A special software in the receiver TED-RX eliminates most interferences.A maximum of transmitting safety:A new dimension of safety is reached due to location optimization by means of optical and acousticsignalling (LED and loudspeaker).Large operation range:TED-TX10: up to approximate 1.5 kmTED-TX400: up to approximate 5 kmAddressing of the system:Up to 16 addresses can be present. One addressed system is not able to receive impulses from a systemwith different addressing (for example if several TED systems are used in the same area).www.alge-timing.com

Data transmission: with absolute safetyIn the data transmission (e.g.of the start time), the data plusthe safety code are transmittedfrom the transmitter TED-TX to the receiver TED-RX.The receiver transmits thedata package to the timing deviceat the finish. This systemis absolutely safe because thedata is transmitted as manytimes as needed in the eventof a faulty radio circuit. Moreover,the third data record alwaysremains stored in thetransmitter TED-TX. Thesame applies to all start timeswhich can be recalled at anytime from the timing device atthe start.ACCESSORYTeledata TEDData transmission / time measurement:The start time is transmitted by radio from the timing device to the finish. Every seconda data set is transmitted. To play it safe every data set is transmitted 10 times.From timing device at start to the finish:StartFinishPhotocellStartgateTiming DeviceTiming DeviceData transmission / Remote control by timing device:TED-TXTED-RXEvery data set is transmitted once. Every 1/10 second a data set can be transmitted: from timing device to display board from timing device to printer from TIMY or COMET terminal to display boardTiming DeviceTED-TXTED-RXDisplay BoardFree data transmission:Any data type can be transmitted. Every 1/10 second a data set is transmitted.Application area: timing device to PC PC to PC PC to display boardTiming Device TED-TX TED-RXPCwww.alge-timing.com

ACCESSORYTeledata TEDALGE Teledata TED – technique that makes you feel safeTED-TX10 TED-TX400 TED-RXTransmitting Capacity 10 mW 400 mW ------------Working Range Up to appr. 1.5 km Up to approx. 5 km ------------Frequency: Standard433,500 MHz 434,600 MHzAlternative434,300 MHz 433,800 MHzall frequenciesInterfaces:Input forRS232Input forRS232Output forRS232 + RS485Power Consumption(one impulse per minute):300 hours 270 hours 54 hoursOperating Temperature: -20° to +50°C -20° to +50°C -20° to +50°CDimensions (without antenna): 198 x 72 x 72 mm 198 x 72 x 72 mm 198 x 72 x 72 mmIMPORTANT:The regulations for radios arevery different all over theworld. Please check if you canuse the radio legally in thecountry that you want to operateit in. In some countriesyou may not use it or you haveto register it.Technical DataAntenna:short, tough, flexibleConnections: compatible with ALGE products and most othersBanana socket for data and start impulseDIN socket with connection for start and stop impulse, data and external supplyInput Signal:closing contact, active low, min. 10 msOutput Signal: transistor, open collector, active low, 100 msLED:for battery indication (TED-TX and TED-RX),and moreover for field intensity indication in the TED-RXLoudspeaker: in the TED-RX for field intensity indication and interface evaluationPower Supply: internal: 6 x AA – Alkaline batteries or6 x AA – NiCd rechargeable batteriesexternal: Charger PS12 or from timing deviceFastening:Velcro fastener for pole fixation, thread for tripod or flange support for photocellAccessory:Case with foam insert for save transportRechargeable battery set with six NiCd batteries for TEDCharger LG6AA for six NiCd rechargeable batteriesChannel extension RX-C10Holder to set up a TED and photocell at one tripod or fastening consoleTED-TX400STARTStartgateSTSn1MSTiming Systemfor Ski RacingTeledataTED-TX10StartPhotocellPR1a-RTor PR1a-dTTeledata TED-TX10TeledataTED-TX10FinishPhotocell PR1a-RTor PR1a-dTFinish Jump OffPhotocell PR1a-RTor PR1a-dTTED-RX400Timy2 PXEPhotocellPR1aFINISH ZIELDisplay BoardStart-StopSwitch 129-06TimeoutPush Button129-06Teledata TED-RXTdC 8001SpeakerDLStNoALGE-TIMINGALGE-TIMINGPUNKTEALGE-TIMINGZEITRANGLED Display Board D-LINETiming Systemfor Show Jumpingwww.alge-timing.com

DISPLAY BOARDD-LINEThe multifunctional LED Display BoardThe ALGE D-LINE series is a very versatile numeric display board. It is possible to control it directly fromALGE timing devices as well as from other devices by RS 232 interface.Additionally, it is possible to show the time of day or use it as simple stand alone stopwatch or countdowndevice. If a DCF or GPS radio receiver and a temperature sensor is purchased with the LED displayboard, the run-time is shown during a sports event and at all other times the board shows alternativelytime and/or temperature.ALGE offers models for indoor and outdoor. The difference lies mainly in the type of LED used. For outdoorpurposes the LED must be a lot brighter especially if the sun shines directly on the board.The following figure heights are in the ALGE program:Indoor:57, 100 mmOutdoor: 80, 150, 250, 450, 600, 800, 1000 and 1500 mmThe standard model has six digits. Of course, we also offer other configurations.The advantage of LED display boards compared to other display boards is the affordable price and lowweight. Moreover, it is possible to use the board also in dark areas (e. g. under dark roof of a stadium).The power for the board is supplied either by mains (100-240 VAC) or an external 12 V car battery.Excellent visual display board for data like:TimesID-numberRankSpeedWidthHeightMarksPointsWeightPriceTemperatureDeparture TimeStock Pricesetc.www.alge-timing.com

DISPLAY BOARDD-LINETechnical Data:LED numeric 7-segment figures with 3 points between the figuresInternal clockInternal push buttonRS232 compatible interfaceConnections:Banana socket for data (RS 232c)Banana socket for external push buttonAmphenol socket (4-pin) for data or power supply (12 VDC)Integrated power supply (100 - 240 VAC, 50-60 Hz)Fastening:2 hangers at the top3/8 “ thread for tripodBlack aluminium case with red plexiglas frontOperating temperature: -20° to 60°CAccessory:DCF radio receiverGPS radio receiverTemperature sensor (max. 2 sensors)Humidity sensorEthernet socket (for time synchronization through ethernet)RS 485 interfaceClip panel e. g. min., sec., 1/100 (for size starting with 150 mm figure height)Digits with 450 mm figure heightDigits with 250 mm figure heightDigits with 150 mm figure heightDigits with 100 mm figure heightNumberofDigitsFigureheightSample of the order code:D-LINE57-I-6-E0Blanks (empty digit) between the digitsNumber of digits, in this case 6 digitsI = Indoor model, O = Outdoor modelFigure height in mm, in this case 57 mmProduct descriptionHeight WidthDepthDistancebetw eenhangersPow erConsumptionDigits with 57 mm figure heightReadingDistance[mm][W] [m]Indoor Models:D-LINE57-I-6-E0 6 57 130 500 60 200 13 25D-LINE100-I-6-E0 6 100 180 800 60 500 13 50Outdoor Models:D-LINE80-O-6-E0 6 80 150 600 60 300 13 40D-LINE150-O-6-E0 6 150 250 956 60 556 14 75D-LINE250-O-6-E0 6 250 350 1493 60 1093 34 125D-LINE450-O-6-E0 6 450 600 2490 80 2090 88 225D-LINE600-O-6-E0 6 600 800 3400 70 3000 133 300D-LINE800-O-6-E0 6 800 1000 4800 70 4400 180 400D-LINE1000-O-6-E0 6 1000 1400 5700 70 5300 270 500D-LINE1500-O-6-E0 6 1500 2000 8500 70 8100 510 750Other configurations than stated above are possible on request!ALGE-TIMINGD-LINE150-O-6-E0ALGE-TIMINGD-LINE250-O-6-E0www.alge-timing.com

DISPLAY BOARDLED Matrix D-RTNMThe D-RTNM is a universal single colour LED matrix board. It is usable as timing display board, message board or for advertisementpurposes. The display can show online preloaded messages or those from the internal memory. Also small animatedfilms can be shown on the board. The lightweight rugged aluminium case allows an easy transport of the board.The outdoor version is excellently readable even at direct sunshine. If used at night or at rainy days, it is possible to selectbetween 100 different brightness levels to reach the best performance of the display at any light condition.Driving is non-multiplexed, that means that these displays last longer and glow brighter than standard multiplexed displays.Further this function is very important e. g. if used during TV broadcast, because the display board does not flicker on the TVscreen.Matrix display board with red LEDModels with 1, 3 or 4 LED per pixelModels for outdoor or indoor useStandard models with 16 or 24 pixel height and 96 or 160 pixel lengthUniversal use by ethernet, RS485 and RS 232 interfaceInternal memory of 4 MB to store pictures, logos, animation or competitor lists. It is possible to run the board fromthe internal memoryPossibility to operate the board directly from the terminal that operates ALGE multisport scoreboardsPossibility to receive the ID-number, time (also running time) and rank directlyfrom ALGE timing devices (e.g. TdC 8001). Additionally it is possible to storethe names and e. g. club or nation in the internal memory of the board.Adjustment of brightness in 100 levelsNon-multiplex controlled LED for longer life time and higher brightnessIntegrated power supply (100 to 240 VAC)Rugged aluminium case with red plexiglas frontOptions:Custom designed models with different pixel resolution on requestNarrow frames for assembling several D-RTNMModels with 7 LED per pixelDifferent colours (yellow, green, blue or white)Connection for temperature sensorConnection for DCF or GPS synchronisation (exact external time signal)two D-RTNM with narrow framesDisplay board controlled directly from ALGE TdC 8001www.alge-timing.com

DISPLAY BOARDLED Matrix D-RTNMDCF, GPS ortemperature sensor (all optional)Pixel types:P1baaP3 P4 P7bbabaRS232 interface with12 VDC outputRS485 with 12 VDC outputRS232 input (e.g. timing device)a + b = 10.0 mma + b = 15.0 mma + b = 20.0 mma = 21.6 mmb = 21.6 mmSample of the order code:a = 20.7 mmb = 25.4 mma = 36.8 mmb = 46.4 mmEthernetD-RTNM-P3-16x96-IPower supply 100 - 240 VACFuseFor models with narrow frames the plugs areintegrated in the backside of the board!I = Indoor, O = OutdoorHorizontal resolution in pixelVertical resolution in pixelPixel with 3 LED (Alternative: 4 or 7 LED)P3 - Pixel with 3 LEDs, H/V pitch 21.6 / 21.6 mmP4 - Pixel with 4 LEDs, H/V pitch 20.7 / 25.4 mmP7 - Pixel with 7 LEDs, H/V pitch 36.8 / 46.4 mmProduct descriptionModelLED perpixelExample of a customer-specific D-RTNMVerticalpixelHorizontalpixelVerticalpixel pitch(mm)Horizontalpixel pitch(mm)Length(mm)Height(mm)Depth(mm)Typical useD-RTNM-P3-16x96-I 3 16 96 21.6 21.6 2300 400 97 indoorD-RTNM-P3-16x160-I 3 16 160 21.6 21.6 3700 400 97 indoorD-RTNM-P4-16x96-I 4 16 96 20.7 25.4 2200 500 97 indoorD-RTNM-P4-16x160-I 4 16 160 20.7 25.4 3500 500 97 indoorD-RTNM-P3-16x96-O 3 16 96 21.6 21.6 2300 400 97 outdoorD-RTNM-P3-16x160-O 3 16 160 21.6 21.6 3700 400 97 outdoorD-RTNM-P4-16x96-O 4 16 96 20.7 25.4 2200 500 97 outdoorD-RTNM-P4-16x160-O 4 16 160 20.7 25.4 3500 500 97 outdoorExamples of models, measurements of other models on request!www.alge-timing.com

DISPLAY BOARDVideowall - LED MatrixLED Matrix Boards are very complex. A lot of specifications influence the price. We would like to give you a short introductionon different terms that are used for LED Matrix Boards:Pixel: One pixel is the smallest point you can show with aMatrix Scoreboard. Any pixel can consist of severalLEDs.Pitch: Describes the distance from pixel to pixel. In general,the pitch starts with 4 mm and goes up to 50 mm.The smaller the pitch, the better the resolution andthe more expensive the board per m².Pixel Size: The bigger the pixel dimension compared to thepitch, the sharper the picture (fill grade).LED/Pixel: Any pixel can consist of one or more LEDs. Themore LEDs per pixel the better the scoreboard. Butthe quality also depends on the type of the LEDs. Inour full color LED screens we only use Nichia LEDsthat have the best performance.Resolution: The resolution is the amount of pixels in verticaland horizontal order. The higher the resolution, thebetter is the quality of the picture or text!Pixelsharing or virtual pixels: The pixelsharing mode isusing LEDs from adjoining pixels to construct virtualpixels. The virtual resolution is four times higherthan the physical number of pixels. But the picturequality of a physical videowall with 16 mm is a lot betterthan the one of a 16 mm shared mode!Luminosity: The luminosity is measured in cd/m² or in Nit(Candela per square meter) and is important for thebrightness of the board. This technical characteristicis also stated in different ways. Some producerswill quote the luminosity for all colors in maximumbrightness. Any serious producer will specifythe brightness in the white-balanced state. Differentcolored scoreboards need different luminosity foroutdoors.1 color 2000 cd/m²2(3) colors 3500 cd/m²full color 5000cd/m² in white-balanced state!!For full color scoreboards it is very important to indicatethe luminosity in white-balanced status. Somemanufacturers will state the brightness in all colorswith 100%. This can result in a brightness of 8,000cd/m² but after the board is calibrated (whitebalanced)it means actually 5,000 cd/m²!Viewing Angle: This is a dimension that is not 100% thesame for different manufacturers. Some producersdefine the maximum angle as before the scoreboardgets dark. This is a poor definition!All serious manufacturers will define the half-centerbrightness, which means in simple words the anglewhere you still have 50% of the full luminosity!Refresh rate: The higher the refresh rate the more softfocussedis the picture.We have a standard refresh rate of 240 and for theprofessional series we have a refresh rate of 500.Static or Multiplexe Driving: The driving method of the LEDsshould be static.You can test this with a digital camera, just watch thevideowall and see if there is a flicker in the picture ofthe camera.The same will happen if a TV camera films the videoscreenand it is broadcasted on TV.Outdoor: The LEDs are completely sealed with a special silicone;horizontal louvers are integrated in the LEDmodules to maximize the contrast.1 Color: The display features only one color (e. g. red). Thiscolor can have different shades to create a better picture(e. g. 256 shades, like a black and white picture).Most of these displays are also able to show animationfiles.2(3) Color: The display consists of LEDs with two differentcolors in each pixel (red and green). This two colorscan be mixed so we can have more than 4000 colors.But all colors are in red, green and yellow tones.Video Wall: The display offers LEDs with three different colorsin each pixel (RGB – red, green, blue). These colorscan be mixed so it has the complete true color spectrum(68 million colors). Such a board has a video inputand it is able to show a TV picture. There are alsoscoreboards available with 10 bit color processingwhich will result in 1073 million colors.www.alge-timing.com

DISPLAY BOARDVideowall - LED MatrixDIECAST ALUMINUM MODULEMains100-240V/50-60HzDVIVGASerial or EthernetPREVIEWVIDEO PROCESSING UNIT VPU340010 bit processingadvanced algorithm for scalingVideo inputs:CVBS, S-Vid, VGA, DVI, YPrPb, SD/HD SDIand HDMILED DRIVING UNIT LDU3000automatic brightness controloffline modecolour correction pixel by pixel and module by modulepixel diagnostic functionINDOOR SYSTEMSModel CH-VFI-4L CH-VFI-6L CH-VFI-8L CH-VFI-9.6L CH-VFI-12LPhysical Pixel Pitch 4 mm 6 mm 8 mm 9.6 mm 12 mmOUTOOR SYSTEMSModel CH-VFO-8S CH-VFO-10S CH-VFO-13S/P CH-VFO-16S/P CH-VFO-20P CH-VFO-26PPhysical Pixel Pitch 8 mm 10 mm 13.3 mm 16 mm 20 mm 26.67 mmVirtual Pixel Pitch - - 6.7 mm 8 mm 10 mm 13,4 mmOutdoor systems with pixelpitches of 10 mm and more are supporting virtual pixel technology!www.alge-timing.com

DISPLAY BOARDLap Counter D-LCALGE offers a wide range of electronic Lap Counters with a figure height of 15 or 25 cm and two or three figures. You mayselect between one-sided, two-sided or three-sided models. The unit is including integrated power pack (integrated batteryand charger), tripod, external push button and, if required, a bell.ModelFigure Reading Number Numberheight distance of digits of facesBellD-LC2-15-1 150 mm 70 m 2 1 noD-LC2-15-2 150 mm 70 m 2 2 noD-LC2-15-3 150 mm 70 m 2 3 noD-LC2-25-1 250 mm 120 m 2 1 noD-LC2-25-2 250 mm 120 m 2 2 noD-LC2-25-3 250 mm 120 m 2 3 noD-LC3-15-1 150 mm 70 m 3 1 noD-LC3-15-2 150 mm 70 m 3 2 noD-LC3-15-3 150 mm 70 m 3 3 noD-LC3-25-1 250 mm 120 m 3 1 noD-LC3-25-2 250 mm 120 m 3 2 noD-LC3-25-3 250 mm 120 m 3 3 noD-LCB2-15-1 150 mm 70 m 2 1 yesD-LCB2-15-2 150 mm 70 m 2 2 yesD-LCB2-15-3 150 mm 70 m 2 3 yesD-LCB2-25-1 250 mm 120 m 2 1 yesD-LCB2-25-2 250 mm 120 m 2 2 yesD-LCB2-25-3 250 mm 120 m 2 3 yesThe lap counter is made for outdoor use age and hasextra bright red LED, that you can see well even indirect sun light. It has a rugged aluminium case andis well-tested in all weather conditions.The lap counter has two program modes:Countdown Laps: From an preset value youcount down until zero. Afterzero the lap counter returnsto the preset value.Countup Laps: For every lap you count onelap up.The lap counter has an automatic powerdown(switches the LED off) to save batteries. After 10minutes without changing the display the energysaving mode activates itself. To re-activate the lapcounter just press the push button.D-LCB3-15-1 150 mm 70 m 3 1 yesD-LCB3-15-2 150 mm 70 m 3 2 yesD-LCB3-15-3 150 mm 70 m 3 3 yesD-LCB3-25-1 250 mm 120 m 3 1 yesD-LCB3-25-2 250 mm 120 m 3 2 yesD-LCB3-25-3 250 mm 120 m 3 3 yesOther configurations than stated above are available on request!Sample of the order code:D-LCB2-25-2Number of facesDigit height in cmNumber of digitsB ... With bellDigital Lap CounterDigit with 150 mmfigure heightDigit with 250 mmfigure heightTechnical Data:Red numeric 7-segment LED figuresTwo or three figuresConnections: Banana socket for external push buttonPower Supply: internal battery or mains (100 - 240 VAC)Integrated power pack (battery with charger)On-Off SwitchAutomatic powerdown after 10 minutes3Fastening: / 8 “ thread for tripodBlack aluminium case with red plexiglas frontOperating temperature: -20° to 60°CTripod to set up the lap counterExternal push button with 10 m cableCertain models: bellwww.alge-timing.com

ALGE-TIMING GmbHRotkreuzstrasse 39A-6890 LustenauAustriaTel: +43-5577-85966Fax: +43-5577-85966-4office@alge-timing.comwww.alge-timing.com