7. operating the multipress - Grass

More documents

Recommendations

Info

8. TROUBLE-SHOOTING AND CORRECTIVE ACTIONIllustration 8-106-01Illustration 8-106-0294The star in your cabinet
8. TROUBLE-SHOOTING AND CORRECTIVE ACTION8-105 The bore head will not move down- Turn off the main switch.- Check the pneumatic lines.- Check the air pressure with the compressed air gauge (manometer). It should be 5.5 - 6 bar.- Check to make sure all pneumatic lines are secure and not loose inside the Multipress. The lines shouldalso not have any damage.- Adjust the non-return throttle valves “9” and “10” (illustration 4-002-03) in + direction as far as possible.- Loosen the pneumatic connection “1” by pressing in the ring “2” (illustration 8-004-01) and pull out thepneumatic hose. Pressing the start button should cause air to come out of this pneumatic line.Warning: Keep hands away from moving parts. If air comes out, then the problem lies with the pneumaticcylinder. If no air comes out, then the problem lies with the controls.- Make certain the exhaust arbor on the vertical bore head is clean. If the exhaust arbor gets stopped up,then the compressed air cannot be released and the cylinder will not move down.If the above tips do not help, please call in a pneumatic technician (see pneumatic diagram, section 4-006).8-106 The components will not insert properly into the drillIllustrations 8-106-01 and 8-106-02Drill a hole pattern. Turn off the main switch. Mount an insertion die which corresponds to thehardware being installed. Place the hardware to be installed on the insertion die. Swing theinsertion die arm down. Set the compressed air on the pressure reducer to 2 bar. Try to insert thecomponent.a) The component is too far left or right.Loosen screw “1” (illustration 8-106-01) with a 4 mm Allen key. Slide the die left or right. Tighten thescrew firmly again.b) The component is too close to the stop guide.Loosen the hexagon nut “2” (illustration 8-106-02) with a 8/10 mm fork wrench. Turn the hexagonnut “3” clockwise to screw out. Tighten the hexagon nut “1”.b) The component is too far away from the stop guide.Loosen the hexagon nut “1” (illustration 8-106-02) with a 8/10 mm fork wrench. Turn the hexagonnut “2” counterclockwise to screw in. Tighten the hexagon nut “1”.Complete point “b” on both sides of the insertion die arm.c) Test and check insertion process to see if the position is correct. If necessary, repeat steps “a” and “b”.The star in your cabinet95
Page 4:
TECHNICAL SPECIFICATIONSWeights:Tot
Page 7 and 8:
TABLE OF CONTENTSPage8. Trouble-sho
Page 9 and 10:
1. GENERAL INFORMATION1-001 List of
Page 11 and 12:
2. SAFETY INFORMATION2-001 Safety i
Page 13 and 14:
2. SAFETY INFORMATION2-006 Dangers
Page 15 and 16:
3. DESCRIPTION OF PRODUCTS3-002 App
Page 17 and 18:
3. DESCRIPTION OF PRODUCTS3-005 Var
Page 19 and 20:
3. DESCRIPTION OF PRODUCTSSide stop
Page 21 and 22:
3. DESCRIPTION OF PRODUCTS3-007 Sta
Page 23 and 24:
4. DESCRIPTION OF MACHINE COMPONENT
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44: 4. DESCRIPTION OF MACHINE COMPONENT
Page 49 and 50: 6. START UP6-001 Pneumatic connecti
Page 51 and 52: 7. OPERATING THE MULTIPRESS7-1 Requ
Page 53 and 54: 7. OPERATING THE MULTIPRESS7-3 Sett
Page 55 and 56: 7. OPERATING THE MULTIPRESS7-304 Se
Page 61 and 62: 7. OPERATING THE MULTIPRESS7-503 Op
Page 63 and 64: 7. OPERATING THE MULTIPRESS7-6 Appl
Page 65 and 66: 7. OPERATING THE MULTIPRESS7-602 Dr
Page 75 and 76: 7. ARBEITEN MIT DER COMBIPRESS7-607
Page 91 and 92: 8. TROUBLE-SHOOTING AND CORRECTIVE
Page 93: 8. TROUBLE-SHOOTING AND CORRECTIVE
Page 105 and 106: 10. MISCELLANEOUS10-001 Guarantee C
Page 107 and 108: 10. MISCELLANEOUS10-002 Disposal Fo
Page 109 and 110: 10. MISCELLANEOUS10-003 Resale Form
Page 111 and 112: 10. MISCELLANEOUS10-004 Questionnai
Page 113 and 114: 10. MISCELLANEOUS10-005 Questionnai
Page 115 and 116: NOTESThe star in your cabinet115
Page 117 and 118: REPRESENTATIVES AROUND THE WORLDMDT
show all

7. operating the multipress - Grass

Create successful ePaper yourself

Delete template?

Save as template?