7. operating the multipress - Grass

More documents

Recommendations

Info

7. OPERATING THE MULTIPRESS192 192 XXIllustration 7-610-01Illustration 7-610-0280The star in your cabinet
7. OPERATING THE MULTIPRESS7-610 Drilling fastening bore holes for cabinet member Illustrations 7-610-01 & 7-610-02Required Equipment:- xx drill bit Ø 5 mm, left, for fastening with Euro screws ( 3 mm Ø for fastening with Spax screws)- xx drill bit Ø 5 mm, right, for fastening with Euro screws ( 3 mm Ø for fastening with Spax screws)Machine Set-Up:When drilling fastening holes for cabinet members, swing the vertical gearbox through 90°.- Turn off the machine at the main switch in the switchgear cabinet.- Lift up the front gearbox cover.- Remove all quick-change drill chucks and drill bits from the gearbox. (See section 7-202).- Fix the new quick-change drill chucks and drill bits to the gearbox. (See section 7-202).- See illustration 7-605-01 for placement of the spindles.- Set the drilling depth, if necessary, in accordance with the instructions given in sections 7-301 and 7-302.See corresponding product documentation for specifications concerning drilling depth.- Set the bore hole spacing, if necessary, in accordance with the instructions given in section 7-303. Seerelevant product documentation for specifications concerning bore hole spacing.- Set the drilling speed of the Multipress, if necessary, in accordance with the instructions given in section7-304.- Activate the travel limit for the vertical bore head, if necessary, in accordance with the instructions given insection 7-305.- Swing the vertical bore head through 90˚ to the right. Pay special attention to section 7-306. There must beno travel limit for the horizontal bore head and no drill bit in the horizontal gearbox!! The left revolver stop(illustration 4-002-02, item “1”) must be set to position 1, 3 or 5 so that the vertical gearbox does notcollide with the horizontal gearbox when drilling.- Set the side stops, in accordance with the instructions given in section 7-501.- Turn on the main switch again. The Multipress is now ready to operate.Operating the Multipress:- Place the workpiece on the machine table with one hand pressed against the stop pins and side stop.- Clamp the workpiece with the hold-down device. This is available as an accessory if needed.- Press the vertical bore head start button with second hand until the depth gauge terminates the drillingcycle or until the bore head reaches the drilling depth set with the knurled screw “6”. (Illustration 4-002-03)- If additional fastening bore holes are needed, slide the workpiece to the next stop and repeat the process.Caution:While the machine is being operated: keep hands clear of the danger area around the hold-down device, theinsertion die arm and the gearbox. The safety information given in section 2 is to be followed whenever themachine is being operated.The star in your cabinet81
Page 4:
TECHNICAL SPECIFICATIONSWeights:Tot
Page 7 and 8:
TABLE OF CONTENTSPage8. Trouble-sho
Page 9 and 10:
1. GENERAL INFORMATION1-001 List of
Page 11 and 12:
2. SAFETY INFORMATION2-001 Safety i
Page 13 and 14:
2. SAFETY INFORMATION2-006 Dangers
Page 15 and 16:
3. DESCRIPTION OF PRODUCTS3-002 App
Page 17 and 18:
3. DESCRIPTION OF PRODUCTS3-005 Var
Page 19 and 20:
3. DESCRIPTION OF PRODUCTSSide stop
Page 21 and 22:
3. DESCRIPTION OF PRODUCTS3-007 Sta
Page 23 and 24:
4. DESCRIPTION OF MACHINE COMPONENT
Page 25 and 26:
Page 27 and 28:
Page 29 and 30: 4. DESCRIPTION OF MACHINE COMPONENT
Page 49 and 50: 6. START UP6-001 Pneumatic connecti
Page 51 and 52: 7. OPERATING THE MULTIPRESS7-1 Requ
Page 53 and 54: 7. OPERATING THE MULTIPRESS7-3 Sett
Page 55 and 56: 7. OPERATING THE MULTIPRESS7-304 Se
Page 61 and 62: 7. OPERATING THE MULTIPRESS7-503 Op
Page 63 and 64: 7. OPERATING THE MULTIPRESS7-6 Appl
Page 65 and 66: 7. OPERATING THE MULTIPRESS7-602 Dr
Page 75 and 76: 7. ARBEITEN MIT DER COMBIPRESS7-607
Page 79: 7. OPERATING THE MULTIPRESS7-609 Dr
Page 91 and 92: 8. TROUBLE-SHOOTING AND CORRECTIVE
Page 105 and 106: 10. MISCELLANEOUS10-001 Guarantee C
Page 107 and 108: 10. MISCELLANEOUS10-002 Disposal Fo
Page 109 and 110: 10. MISCELLANEOUS10-003 Resale Form
Page 111 and 112: 10. MISCELLANEOUS10-004 Questionnai
Page 113 and 114: 10. MISCELLANEOUS10-005 Questionnai
Page 115 and 116: NOTESThe star in your cabinet115
Page 117 and 118: REPRESENTATIVES AROUND THE WORLDMDT
show all

7. operating the multipress - Grass

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?