7. operating the multipress - Grass

More documents

Recommendations

Info

7. OPERATING THE MULTIPRESSIllustration 7-501-01Illustrations 7-502-01, 7-502-02, 7-502-03, 7-502-0458The star in your cabinet
7. OPERATING THE MULTIPRESS7-5 Setting the Multipress - General information7-501 Setting the side stops Illustration 7-501-01Tools required: 5 mm Allen keyLoosen the screw “1” with the 5 mm Allen key “2” by turning counterclockwise. Slide the stop “3” to thedesired size. The side with the measurements marked “3” is the side with the side stops. Tighten the screw“1” clockwise.To prevent errors between the left and right, we recommend using a stop adjustment gauge as the secondside.The stop adjustment gauge and the zero-point retainer “4” are included in the standard equipment.7-502 Operating the stop adjustment gauge Illustrations 7-502-01, 7-502-02, 7-502-03,7-502-04Tools required: 5 mm Allen key- After adjusting the side stops “A“ and “B“ for the right side, adjust the left side. For example, the hinges aremounted on the left and right doors.- Insert the pin “1” (illustration 7-502-01) in the bore hole “2” (illustration 7-502-01) in the center of the zeropoint gauge “3”.- Loose the flap screw “4” (illustration 7-307-02). Slide the adjustment ring “5” (illustration 7-502-01) againstthe stop catch “6” (illustration 7-502-01) of the side stops “B”. Tighten the flap screw “4” (illustration7-502-02). Caution: The flap screw must point upward. If necessary, use more adjustment rings “5”.- Press down all stop catches “6”.- Swing the adjustment gauge “8” through 180˚ to the left side (illustration 7-502-03).- Loosen a stop “C” on the left side (illustration 7-502-04). Slide the stop “C” against the adjustment ringuntil the stop catch lines up with the adjustment ring. Tighten the side stops.- If necessary, use more stops.If the same hole patterns are repeated, we recommend getting a stop adjustment gauge for each hole patternand replacing the flap screws with set screws. This allows the desired hole patterns to be sized exactlyand precisely on both sides at anytime by means of a stop adjustment gauge.The star in your cabinet59
Page 4:
TECHNICAL SPECIFICATIONSWeights:Tot
Page 7 and 8: TABLE OF CONTENTSPage8. Trouble-sho
Page 9 and 10: 1. GENERAL INFORMATION1-001 List of
Page 11 and 12: 2. SAFETY INFORMATION2-001 Safety i
Page 13 and 14: 2. SAFETY INFORMATION2-006 Dangers
Page 15 and 16: 3. DESCRIPTION OF PRODUCTS3-002 App
Page 17 and 18: 3. DESCRIPTION OF PRODUCTS3-005 Var
Page 19 and 20: 3. DESCRIPTION OF PRODUCTSSide stop
Page 21 and 22: 3. DESCRIPTION OF PRODUCTS3-007 Sta
Page 23 and 24: 4. DESCRIPTION OF MACHINE COMPONENT
Page 49 and 50: 6. START UP6-001 Pneumatic connecti
Page 51 and 52: 7. OPERATING THE MULTIPRESS7-1 Requ
Page 53 and 54: 7. OPERATING THE MULTIPRESS7-3 Sett
Page 55 and 56: 7. OPERATING THE MULTIPRESS7-304 Se
Page 57: 7. OPERATING THE MULTIPRESS7-4 Sett
Page 61 and 62: 7. OPERATING THE MULTIPRESS7-503 Op
Page 63 and 64: 7. OPERATING THE MULTIPRESS7-6 Appl
Page 65 and 66: 7. OPERATING THE MULTIPRESS7-602 Dr
Page 75 and 76: 7. ARBEITEN MIT DER COMBIPRESS7-607
Page 91 and 92: 8. TROUBLE-SHOOTING AND CORRECTIVE
Page 105 and 106: 10. MISCELLANEOUS10-001 Guarantee C
Page 107 and 108: 10. MISCELLANEOUS10-002 Disposal Fo
Page 109 and 110:
10. MISCELLANEOUS10-003 Resale Form
Page 111 and 112:
10. MISCELLANEOUS10-004 Questionnai
Page 113 and 114:
10. MISCELLANEOUS10-005 Questionnai
Page 115 and 116:
NOTESThe star in your cabinet115
Page 117 and 118:
REPRESENTATIVES AROUND THE WORLDMDT
show all

7. operating the multipress - Grass

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?