7. operating the multipress - Grass

More documents

Recommendations

Info

5. SHIPPING AND INSTALLATION OF THE MACHINE5-001 Shipping and storage requirementsThe Multipress is shipped completely assembled and is delivered fastened to a Euro-pallet.The Multipress can also be delivered in a wooden crate on request.Protect the machine against humidity and moisture in transit and storage.The storage temperature should range between -20 ˚C to +50 ˚C.5-002 Space and environment requirementsThe space required depends on the sizes of the workpieces to be processed.The minimum depth required is about 200 cm.The minimum width required is about 100 cm; add to that another 100 cm per extension bar and per side.For high cabinets whose individual components have a height of 240 cm, a space requirement of 5 meters inthe width must be calculated.The machine must be kept in a dry space and protected from humidity and moisture.The temperature of the area where the machine is being operated should be within the range of +10 ˚C to+40 ˚C.The relative humidity should range between 10% to 80% and should be non-condensing.Major deviations in these specifications could lead to malfunctions or damage to the machine.5-003 Setting up at final destinationThe Multipress drilling and insertion machine is delivered completely assembled and ready to operate. Themachine has been tested and adjusted at the manufacturing plant.If the Multipress is packaged in a protective frame, it can be handled by a lift truck below the frame.If it is not packaged in a protective frame, it can be handled by a lift truck below the pallet. At the final destination,the machine is raised using the eyebolt on the machine frame and placed on the previously preparedbase.Warning: Do not lift the machine by the machine table.48The star in your cabinet
6. START UP6-001 Pneumatic connectionsThe Multipress is equipped with 2-meter long air hose Ø 6/3. Depending on the destination country, Euroquick coupling is installed.See section 4-006, pages 36-43, for the wiring diagram.Connection:Warning:Once the machine is connected pneumatically (pressure), the vertical bore head motor supportwith the gearbox can move up and the horizontal bore head motor support with the gearbox canmove back.a) Lift the setting knob of the maintenance unit and turn counterclockwise.b) Connect the pneumatic air pressure with a quick coupling or shut-off valve with an exhaust.It has to be connected so that the machine operators can disconnect the machine from the pneumaticductwork system at anytime within a maximum distance of 3 meters.c) Turn the regulator clockwise until the pressure gauge of the maintenance unit indicates about5.5 to 6 bar (0.55 - 0.6 MPa). Press the setting knob back down.d) Test if it functions with the main switch turned off and without the drill bit. By activating the start button,the motor support has to move downward. When the button is released, the machine returns immediatelyto its starting position.e) Check the pneumatic hold-down device (accessory) to see if it operates properly.6-002 Electric connectionsThe machine is equipped with a 3-meter long 5-pole connecting cable. Depending on the destinationcountry, a socket (CEE 5 x 16A) is installed.See section 4-007, pages 44 and 45, for the wiring diagram.Warning:Only authorized technicians or licensed electricians should hook up this machine. They mustcomply with the codes and regulations applicable in the respective country.If any maintenance work is to be done on the electrical system of the Multipress, the machinemust be disconnected from the power supply by pulling out the plug or by means of a switch thatcan be locked.After the start-up is completed in accordance with section 6-001, and the hook-up to the power supply iscompleted, turn on the main switch, swing the insertion die arm completely up, and without a drill bit, pressthe vertical motion start button “2“, illustration 4-004-01, until the motor starts. Release the start button toreturn the machine to the starting position. While the motor is shutting off, check the direction of the rotationthrough the ventilation grill. The direction of rotation must correspond to the arrow marked on the motor cover.Only an authorized technician or licensed electrician may change the direction of rotation.6-003 Other connectionsDust collection vacuum connection has a diameter of 100 mm.The required suction capacity is about 2000 m 3 /h.See also section 3-001 “Dust and noise emission values“.Warning:In some countries (the European Community countries, for example), the Multipress maynot be operated without the dust vacuum system.The star in your cabinet49
Page 4: TECHNICAL SPECIFICATIONSWeights:Tot
Page 7 and 8: TABLE OF CONTENTSPage8. Trouble-sho
Page 9 and 10: 1. GENERAL INFORMATION1-001 List of
Page 11 and 12: 2. SAFETY INFORMATION2-001 Safety i
Page 13 and 14: 2. SAFETY INFORMATION2-006 Dangers
Page 15 and 16: 3. DESCRIPTION OF PRODUCTS3-002 App
Page 17 and 18: 3. DESCRIPTION OF PRODUCTS3-005 Var
Page 19 and 20: 3. DESCRIPTION OF PRODUCTSSide stop
Page 21 and 22: 3. DESCRIPTION OF PRODUCTS3-007 Sta
Page 23 and 24: 4. DESCRIPTION OF MACHINE COMPONENT
Page 47: 4. DESCRIPTION OF MACHINE COMPONENT
Page 51 and 52: 7. OPERATING THE MULTIPRESS7-1 Requ
Page 53 and 54: 7. OPERATING THE MULTIPRESS7-3 Sett
Page 55 and 56: 7. OPERATING THE MULTIPRESS7-304 Se
Page 61 and 62: 7. OPERATING THE MULTIPRESS7-503 Op
Page 63 and 64: 7. OPERATING THE MULTIPRESS7-6 Appl
Page 65 and 66: 7. OPERATING THE MULTIPRESS7-602 Dr
Page 75 and 76: 7. ARBEITEN MIT DER COMBIPRESS7-607
Page 91 and 92: 8. TROUBLE-SHOOTING AND CORRECTIVE
Page 99 and 100:
8. TROUBLE-SHOOTING AND CORRECTIVE
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
10. MISCELLANEOUS10-001 Guarantee C
Page 107 and 108:
10. MISCELLANEOUS10-002 Disposal Fo
Page 109 and 110:
10. MISCELLANEOUS10-003 Resale Form
Page 111 and 112:
10. MISCELLANEOUS10-004 Questionnai
Page 113 and 114:
10. MISCELLANEOUS10-005 Questionnai
Page 115 and 116:
NOTESThe star in your cabinet115
Page 117 and 118:
REPRESENTATIVES AROUND THE WORLDMDT
show all

7. operating the multipress - Grass

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?