7. operating the multipress - Grass

More documents

Recommendations

Info

2. SAFETY INFORMATION2-003 Risks pursuant to EN 292-2The design and construction of the Multipress hinge drilling and insertion machine is based on state-of-theartand known safety and technical standards. Its use may nevertheless harbor risks for the life and health ofthe operator or of third parties, as well as damage to the machine and other property.Residual risks exist:- If the start button is activated, caution: even if the main switch is turned off, the machine can move;- If the machine is operated by unqualified personnel;- If the machine is operated without recommended safety devices;- In the event of inappropriate tooling or incorrect installation or attachment of tooling;- In the event of the improper placement of the operator’s second hand during drilling, inserting or installingof machine parts;- If additional person(s) is/are in the area of the operating machine.- In the event of contact with a machine that has not been turned off and secured in the proper manner.- If the machine is not properly maintained as described in section 7-0 “Operating the Multipress.”- If the control elements fail.These residual risks can be reduced by adhering to the information found in sections 2-0 and 7-0.2-004 Safety devicesSafety devices, information about dangers and risks, etc. serve to ensure safety and may not, under any circumstances,be removed or be made inoperable.- The main switch, which can be locked off to prevent unauthorized start-ups when switched off during adjustmentand set-up operations.- The pneumatic filter reducing regulator prevents the machine from overloading. (See section 4-006).- See the electric diagram in section 4-007 for information on the protection of thermal overload on the electricmotor.- Back pressure valve controls, located directly on the main cylinder, prevent the machine from descending inthe event the compressed air is lost. The valve is first opened when the start button is activated. (See thepneumatic wiring diagram in section 4-006).- The motor first runs when the start button is activated. After the start button is released or the depth gaugecaliper is activated at the vertical bore head, the motors switch off with a time delay. The time delay can beset on the switchgear cabinet.- The motor does not run during the insertion process.- The integrated dust collection system protects personnel from fine dust and, also, simultaneously protectspersonnel from injury by preventing contact with the drill.2-005 Description of stickersWARNING:The drill unit may descend evenif the motor is turned off.This sticker warns that the drill unit may descend even whenthe motor is turned off.This sticker indicates EC (European Community) conformity.This sticker is a warning sign that only one person shouldoperate the machine at a time.This sticker is a warning sign that indicates danger ofcrushing and to keep hands or other objects clear.This sticker indicates that operating instructions andinformation should be read thoroughly.12The star in your cabinet
2. SAFETY INFORMATION2-006 Dangers and safety measuresDangersTool releaseTool breakContact with toolTool has contact with machineWorkpiece is thrown outFeed mechanismworkpiece clamping device(available as an accessory)Risk of impactDriveTool setControl systemTool starts unexpectedlyControl systemUnexpected lifting stroke releaseControl systemPress to begin tool startElectricityNoiseDustSafety measuresChuck with clamping screwUse exclusively authorized products(Available from the Grass product line)All tools are behind transparent coversSafety drilling depth stopWorkpiece stopsNo automatic feed motionMaximum 6 mm adjustmentNot applicable because the stroke motion is slowThe direct drive is completely enclosed in a gearboxForward feed for stroke motion is activated by a non self-lockingbutton with collar. Meets safety margins to EN 294 in accordancewith the risks.Electric control with P/E converter, non self-locking buttonwith collarNon self-locking button with collarInterrogate feature of insertion die arm with pneumatic valveEquipment in compliance with EN 60204, Part 1, VDE 0100 andIEC 384Measured emissions values correspond to the current state oftechnology. The workplace emissions ratings are under 85 dB(A).The wood dust emissions fall below the required limits with thedust collection system connected.The star in your cabinet13
Page 4: TECHNICAL SPECIFICATIONSWeights:Tot
Page 7 and 8: TABLE OF CONTENTSPage8. Trouble-sho
Page 9 and 10: 1. GENERAL INFORMATION1-001 List of
Page 11: 2. SAFETY INFORMATION2-001 Safety i
Page 15 and 16: 3. DESCRIPTION OF PRODUCTS3-002 App
Page 17 and 18: 3. DESCRIPTION OF PRODUCTS3-005 Var
Page 19 and 20: 3. DESCRIPTION OF PRODUCTSSide stop
Page 21 and 22: 3. DESCRIPTION OF PRODUCTS3-007 Sta
Page 23 and 24: 4. DESCRIPTION OF MACHINE COMPONENT
Page 49 and 50: 6. START UP6-001 Pneumatic connecti
Page 51 and 52: 7. OPERATING THE MULTIPRESS7-1 Requ
Page 53 and 54: 7. OPERATING THE MULTIPRESS7-3 Sett
Page 55 and 56: 7. OPERATING THE MULTIPRESS7-304 Se
Page 61 and 62: 7. OPERATING THE MULTIPRESS7-503 Op
Page 63 and 64:
7. OPERATING THE MULTIPRESS7-6 Appl
Page 65 and 66:
7. OPERATING THE MULTIPRESS7-602 Dr
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
7. ARBEITEN MIT DER COMBIPRESS7-607
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
8. TROUBLE-SHOOTING AND CORRECTIVE
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
10. MISCELLANEOUS10-001 Guarantee C
Page 107 and 108:
10. MISCELLANEOUS10-002 Disposal Fo
Page 109 and 110:
10. MISCELLANEOUS10-003 Resale Form
Page 111 and 112:
10. MISCELLANEOUS10-004 Questionnai
Page 113 and 114:
10. MISCELLANEOUS10-005 Questionnai
Page 115 and 116:
NOTESThe star in your cabinet115
Page 117 and 118:
REPRESENTATIVES AROUND THE WORLDMDT
show all

7. operating the multipress - Grass

Create successful ePaper yourself

Delete template?

Save as template?