7. operating the multipress - Grass

More documents

Recommendations

Info

8. TROUBLE-SHOOTING AND CORRECTIVE ACTIONIllustration 8-205-01145213Illustration 8-206-02102The star in your cabinet
8. TROUBLE-SHOOTING AND CORRECTIVE ACTION8-205 Horizontal bore head is not parallel to the machine table Illustration 8-205-01Required tools:6 mm Allen key8 - 10 mm fork wrench- Turn off the main switch.- Loosen the 4 gearbox fastening screws “1” (illustration 8-205-01) with a 6 mm Allen key by turning 3/4 to1 turn counterclockwise.- Loosen both lock nuts “2” with the 10 mm fork wrench.- Loosen the lower or the upper adjusting screw “3” depending on the problem.If the left spindle is higher than the center spindle:loosen the lower adjusting screw “3” clockwise;readjust the upper adjusting screw “3” clockwise until both the spindles are the same height.- Tighten the 4 gearbox fastening screws “1” (illustration 8-205-01) with 6 mm Allen key.- Reset the lower adjusting screw “3”.- Tighten both lock nuts “2”.- Turn main switch back on again.- Test drill. See section 7-701.- Check the results. If necessary, repeat the adjustment.8-206 Horizontal bore head does not align with the vertical bore headIllustration 8-206-02Drill the vertical dowel hole, as described in section 7-609, and the horizontal dowel hole, as described insection 7-701, on the same side stop, and then fasten both parts with a wooden dowel. If there is aprojection or excess on the stop side of the workpiece, the horizontal bore head must be adjusted.Problem: The bore head is too far left.Required tool:6 mm Allen key8 - 10 mm fork wrench- Turn off the main switch.- Remove all quick-change drill chucks from the horizontal gearbox.- Set the revolver stop for the shortest stop screw as the drilling depth.- Manually pull the horizontal bore head completely to the front.- Set the bore hole spacing on the vertical bore head at the front on the hand wheel under the machine tableto the dimensions of about 5 - 10 mm.- Loosen the 4 Allen screws “1” , 2 on each side, with a 6 mm Allen key by turning 3/4 to 1 turn counterclockwise.- Loosen both lock nuts “2” with the 10 mm fork wrench.- Loosen the Allen screws “3” about 3 - 5 mm counterclockwise with a 5 mm Allen key.- Readjust the Allen screw ”4” clockwise with a 5 mm Allen key.- 1 turn corresponds to an adjustment of about 1 mm.- Adjust the Allen screw “3” up to the stop “5”.- Tighten both lock nuts “2” with the 10 mm fork wrench.- Tighten the 4 Allen screws with the 6 mm Allen key.- Slide the horizontal bore head manually back to the stop.- Drill the vertical dowel hole, as described in section 7-609, and the horizontal dowel hole, as described insection 7-701 on the same side stop, and then fasten both parts with a wooden dowel. Check the results.If necessary, repeat the process.After a successful adjustment, please make sure the gearbox is parallel to the machine table and check thedigital position indicator on the horizontal bore head.The star in your cabinet103
Page 4:
TECHNICAL SPECIFICATIONSWeights:Tot
Page 7 and 8:
TABLE OF CONTENTSPage8. Trouble-sho
Page 9 and 10:
1. GENERAL INFORMATION1-001 List of
Page 11 and 12:
2. SAFETY INFORMATION2-001 Safety i
Page 13 and 14:
2. SAFETY INFORMATION2-006 Dangers
Page 15 and 16:
3. DESCRIPTION OF PRODUCTS3-002 App
Page 17 and 18:
3. DESCRIPTION OF PRODUCTS3-005 Var
Page 19 and 20:
3. DESCRIPTION OF PRODUCTSSide stop
Page 21 and 22:
3. DESCRIPTION OF PRODUCTS3-007 Sta
Page 23 and 24:
4. DESCRIPTION OF MACHINE COMPONENT
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
6. START UP6-001 Pneumatic connecti
Page 51 and 52: 7. OPERATING THE MULTIPRESS7-1 Requ
Page 53 and 54: 7. OPERATING THE MULTIPRESS7-3 Sett
Page 55 and 56: 7. OPERATING THE MULTIPRESS7-304 Se
Page 61 and 62: 7. OPERATING THE MULTIPRESS7-503 Op
Page 63 and 64: 7. OPERATING THE MULTIPRESS7-6 Appl
Page 65 and 66: 7. OPERATING THE MULTIPRESS7-602 Dr
Page 75 and 76: 7. ARBEITEN MIT DER COMBIPRESS7-607
Page 91 and 92: 8. TROUBLE-SHOOTING AND CORRECTIVE
Page 101: 8. TROUBLE-SHOOTING AND CORRECTIVE
Page 105 and 106: 10. MISCELLANEOUS10-001 Guarantee C
Page 107 and 108: 10. MISCELLANEOUS10-002 Disposal Fo
Page 109 and 110: 10. MISCELLANEOUS10-003 Resale Form
Page 111 and 112: 10. MISCELLANEOUS10-004 Questionnai
Page 113 and 114: 10. MISCELLANEOUS10-005 Questionnai
Page 115 and 116: NOTESThe star in your cabinet115
Page 117 and 118: REPRESENTATIVES AROUND THE WORLDMDT
show all

7. operating the multipress - Grass

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?