Average rates for painting - Resene

More documents

Recommendations

Info

Resene Professional development programmeGood painting practice emphasises the importance of preparation, particularly for repainting andcleanliness is the key! Cleaning is easily achieved with Sugar soap and propriety solutions like ReseneInterior Paintwork Cleaner and because it is an integral component of painting specification rates areincluded separately to actual coating costs.Step 1 – WashingWashing before painting interior walls, ceilings and joinery etc is good practice to remove any fly dirt, dust and othercontaminants. In most situations this means simply wiping using a clean lint-free cloth and a solution of warm waterand Resene Interior Paintwork Cleaner or a mild detergent. Sanding walls and ceilings is not usually necessary unlessthe surface has imperfections and/or flaking paint that needs to be sanded smooth, or if the existing paint systemis an old enamel system.If it is an enamel system, commonly used in kitchen and bathroom areas and on joinery and doors, first remove anygrease and oil using Sugar soap and sand the areas to degloss the surface and provide a key for the paint to adhereto. Alternatively Resene Waterborne Smooth Surface Sealer (D47a) could be used eliminating the requirement tosand.Note 1: Pen marks will need to be sealed with either Resene Sureseal (D42) or Resene Enamel Undercoat (D44) asthey will bleed through waterborne paints.Note 2: You can check whether the paint finish is an enamel system by rubbing the paint surface with meths. If itremoves some of the coating then it is most likely waterborne and a Resene paint system can be applied directly ontothe clean surface without sanding.Step 2 – FillingAny holes or voids, such as those left in wallboards by picture hooks, should be filled and once dry sanded smooth.Unless the hole in the wallboard is large (say bigger than the palm of your hand) it will not usually need sealing orpriming before painting.For timber joinery it is good practice to spot prime voids and holes, such as punched nailheads, before filling andthen reprime once filled and sanded. The tables below are guides to the most suitable sandpaper, fillers and primers/sealers to use.You are now ready to paint.Sanding and scrapingArea Scraper First sandpaper FinishingsandpaperFine finishing – clear finishes - 220 grit zinc stearate 400 grit Wet and DryRough and/or flaking woodwork or wallliningsSanding between costs, enamels, clearfinishing25mm-50mm flat 100 grit zinc stearate 220 grit zinc stearatebladed scraper- 220 grit zinc stearate -Sanding fillers for joinery, skirting boards etc - 180 grit zinc stearate -Sanding fillers on wall linings - 220 grit zinc stearate -Sanding wallboards after removing wallpaper - 80 grit zinc stearate -Wallboard compounds, Resene BroadwallSurface Prep and Seal (D807), ReseneBroadwall Waterborne Wallboard Sealer(D403)- 180-220 grit zincstearate – ideallywith a pole sander-21
Resene Professional development programmeFillersSubstrate Recommended AlternativeGaps between scotia, skirting boards and door and window frames Selleys No More Resene Gap FillerGapsHoles/voids in timber and MDF joinery PAL Contract Filler Selleys PermafillSmall holes, dents etc in wallboards (e.g. picture hook holes) Selleys Rapid Filler PAL Contract FillerPrimingSubstrate New AgedCedar joinery Resene Enamel Undercoat (D44) Resene Enamel Undercoat (D44)Laminated surfaces - Resene Waterborne Smooth Surface Sealer(D47a)MDFResene Quick Dry Waterborne PrimerUndercoat (D45)Resene Quick Dry Waterborne PrimerUndercoat (D45)Old varnish/polyurethane - Resene Waterborne Smooth Surface Sealer(D47a)Paperfaced plasterboard Resene Broadwall WaterborneWallboard Sealer (D403)Resene Sureseal (D42)Timber joineryInterior workResene Quick Dry Waterborne PrimerUndercoat (D45)Hour% factorMeasureResene Quick Dry Waterborne PrimerUndercoat (D45)Vinyl wallpaper - Resene Vinyl Wallpaper Sealer (D406)Water stains/pen and ink - Resene Sureseal (D42)marks$ rate labour/ materialsWashing down surfaces apply Resene Paint Prep andHousewash, scrub and rinse clean (general surfaces) 0.10 m 2 5.20Apply Resene Emulsifiable Solvent Cleaner (D804) togreasy or smoke damaged surfaces flush clean water washand vacuum dry (grease and smoke) 0.12 m 2 5.60Wash, sand and seal varnished surfaces with adhesionprimer 0.14 m 2 7.80Stripping wallpaper(a) standard(b) vinyl(c) embossed* indicative rate only – try for labour hourly rate0.140.160.1811.60m 2m 2 12.60m 2 9.60Skim coat plasterboard walls after paper removal 0.18 m 2 12.50interior preparatory washing/sealing – repaintsCall 0800 RESENE (737 363), visit www.resene.co.nzor email us at advice@resene.co.nz22
Page 6 and 7: Resene Professional development pro
Page 72 and 73:
Resene Professional development pro
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82:
In Australia:PO Box 924, Beenleigh,
show all

Average rates for painting - Resene

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?