Viola M4BL User Manual - Astra Security Systems Ltd
Viola M4BL User Manual - Astra Security Systems Ltd Viola M4BL User Manual - Astra Security Systems Ltd
(NTSC), discrete).Please note that the total Event Record IPS should not exceed the systemrecording capacity (NTSC: 240/CIF, 120/Half-D1, 60/Full-D1; PAL: 200/CIF,100/Half-D1, 50/Full-D1), or the system will lower the actual rate automaticallyat recording.• Normal Record IPS – the normal record IPS for this camera. This camera willbe recorded at this rate if no event occurs. Press +/- buttons to select the value(0 – Event Record IPS for this camera, discrete).6.1.1 Motion SetupIn Camera Setup, press ENTER to call up Motion Setup as shown when thehighlighted option is Motion Settings.. of the camera to setup. The Motion setupallows the administrator to define how the system responds to the detected motion forthe camera.The general operations are as below:• ▲▼ (Mouse: Left click)Press these buttons to select the items.• NumericPress these buttons to select the camera.• COPY ( )Press this button to copy the Motion settings, including Detection settings, of thefocus camera to all the following cameras. (EX. focus camera is 1, its Motion- 32 -
settings will be copied to those of cameras 2-4.)• ESC (Mouse: Right Click)Press this button to escape from this screen, and return to Camera Setup display.If the Save dialog is shown, press ENTER to exit and save, ESC (Mouse:Right Click) to exit without saving.Following is a brief description for each item and its specific operations:• Duration – response duration to define at most how long (in seconds) the Buzzerwill keep being triggered after motion is detected for this camera. However, theBuzzer will be reset immediately once the camera returns to normal. Press +/-buttons to adjust the value (3 seconds - 60 minutes, discrete, ‘-‘ for ‘Forever’).• Pre-record – to define how long before motion is detected this camera shall beintensively recorded at Event Record IPS. Press +/- buttons to adjust the value(0-10 seconds, discrete). Please note that the actual pre-record time may beshorter than the value set if the total size of the pre-record pictures exceeds thepre-record buffer size of the system.• Post-record – to define how long after motion is detected this camera shall beintensively recorded at Event Record IPS. Press +/- buttons to adjust the value(0 second - 60 minutes, discrete).• Buzzer – to activate the internal Buzzer or not when motion of this camera isdetected. Press ENTER or +/- (Mouse: Left click) to check/uncheck this item.The default setting is “ˇ” - checked.• Log – to log to event logs or not. Press ENTER or +/- to check/uncheck thisitem. The default setting is “ˇ” - checked.• E-mail – to send the event e-mail to remote station or not. The e-mail will besent to the predefined receivers when the event is triggered. Press ENTER or+/- to check/uncheck this item. The default setting is “–” - unchecked.• Detection Settings.. – used to setup the motion detection settings, includingdetection area and sensitivity, when motion is detected for this camera. Pleasenote that the detection area and sensitivity are also used for the Smart Searchinformation. There won’t be any Smart Search information stored outsidethe detection area. So, it’s better to enable the whole area if the motiondetection for the camera is disabled (and only Smart Search is used). PressENTER in Settings.. to call up Motion Detection Setup (as shown) for thiscamera. In Motion Detection Setup, the video area is divided into many smallgrids, and the area with gray grids is the area which will be detected for motion,while transparent grids not detected for motion. Besides, there is a (yellow)Mask window.- 33 -
- Page 5 and 6: Table of Contents1. Product Overvie
- Page 7 and 8: 1. Product OverviewThe H.264 digita
- Page 9 and 10: 2.2 Back Panel1. Video Input Connec
- Page 11 and 12: 8. Down/DEL Button (▼/DEL)Press t
- Page 13 and 14: 3. InstallationsThe installations d
- Page 15 and 16: 4. Main Screen And Basic Operations
- Page 17 and 18: 4.2 Login And LogoutThere are three
- Page 19 and 20: • ENTER (Mouse: )Press this butto
- Page 21 and 22: 5. Menu DisplayIn split-window disp
- Page 23 and 24: • ESC (Mouse: or Right Click)Pres
- Page 25 and 26: 5.3 Backup DeviceIn Menu display, p
- Page 27 and 28: 5.4 Software Upgrade (Administrator
- Page 29 and 30: 6. Setup (Administrator)In Menu dis
- Page 31: exit without saving.Following is a
- Page 35 and 36: for the motion detection of this ca
- Page 37 and 38: Press this button to escape from th
- Page 39 and 40: • ESC (Mouse: Right Click)Press t
- Page 41 and 42: • Setup System - to enable the us
- Page 43 and 44: • System Time -• Synchronizatio
- Page 45 and 46: • Net Mask - Net Mask for the IP
- Page 47 and 48: • Username - username if the SMTP
- Page 49 and 50: 80. Please follow the Text Input me
- Page 51 and 52: 7.1 Search By TimeThe screen for Se
- Page 53 and 54: Please select the backup device, an
- Page 55 and 56: Press these buttons to select the d
- Page 57 and 58: 7.4 Search Archived FilesThe screen
- Page 59 and 60: Following is a brief description fo
- Page 61 and 62: file to self-playback the correspon
- Page 63 and 64: 7.8 Playback For Archived FilesIn S
- Page 65 and 66: 9. Please go to Start->Setup->Contr
- Page 67 and 68: • In video window, right-click th
- Page 69 and 70: selected DVR. Click on any of these
- Page 71 and 72: • PCIBM PC/AT compatible with Int
- Page 73 and 74: Appendix A - SpecificationsSystemVi
- Page 75 and 76: Appendix B - Time Zone TableTime Zo
- Page 77 and 78: Appendix C - Recording TableNTSC Re
- Page 79 and 80: Appendix D - MS-Windows UtilitiesTh
- Page 81: M4V/H.264 to AVI Conversion Utility
settings will be copied to those of cameras 2-4.)• ESC (Mouse: Right Click)Press this button to escape from this screen, and return to Camera Setup display.If the Save dialog is shown, press ENTER to exit and save, ESC (Mouse:Right Click) to exit without saving.Following is a brief description for each item and its specific operations:• Duration – response duration to define at most how long (in seconds) the Buzzerwill keep being triggered after motion is detected for this camera. However, theBuzzer will be reset immediately once the camera returns to normal. Press +/-buttons to adjust the value (3 seconds - 60 minutes, discrete, ‘-‘ for ‘Forever’).• Pre-record – to define how long before motion is detected this camera shall beintensively recorded at Event Record IPS. Press +/- buttons to adjust the value(0-10 seconds, discrete). Please note that the actual pre-record time may beshorter than the value set if the total size of the pre-record pictures exceeds thepre-record buffer size of the system.• Post-record – to define how long after motion is detected this camera shall beintensively recorded at Event Record IPS. Press +/- buttons to adjust the value(0 second - 60 minutes, discrete).• Buzzer – to activate the internal Buzzer or not when motion of this camera isdetected. Press ENTER or +/- (Mouse: Left click) to check/uncheck this item.The default setting is “ˇ” - checked.• Log – to log to event logs or not. Press ENTER or +/- to check/uncheck thisitem. The default setting is “ˇ” - checked.• E-mail – to send the event e-mail to remote station or not. The e-mail will besent to the predefined receivers when the event is triggered. Press ENTER or+/- to check/uncheck this item. The default setting is “–” - unchecked.• Detection Settings.. – used to setup the motion detection settings, includingdetection area and sensitivity, when motion is detected for this camera. Pleasenote that the detection area and sensitivity are also used for the Smart Searchinformation. There won’t be any Smart Search information stored outsidethe detection area. So, it’s better to enable the whole area if the motiondetection for the camera is disabled (and only Smart Search is used). PressENTER in Settings.. to call up Motion Detection Setup (as shown) for thiscamera. In Motion Detection Setup, the video area is divided into many smallgrids, and the area with gray grids is the area which will be detected for motion,while transparent grids not detected for motion. Besides, there is a (yellow)Mask window.- 33 -