Datacomtools.comTM

Validator PRO & PRO-NT
Building on the capabilities of the Validator & Validator-NT, the JDSU ValidatorPRO
series of Ethernet Network Management Tools offers a solution to test copper and fiber
Ethernet cables. The ValidatorPRO Ethernet speed certifier with integrated optical
power meter and accompanying Plan-Um® cable management software delivers the power to test both
copper and fiber cabling, determine if cables can support Gigabit Ethernet, and perform troubleshooting for
cable installations. The ValidatorPRO performs all tests offered by the Validator & Validator-NT, including
speed certifying the data-carrying capabilities of copper Ethernet network cables up to 1 Gb/s by testing
for noise in the network, detecting faults in the cabling wiring, & ensuring that cables can support the speed
capabilities of active equipment.
To certify Ethernet speed performance of cable runs, the ValidatorPRO series of handheld testers conducts
bit error rate (BER) tests by sending data packets down specified cable runs at defined data rates to check
for errors at the maximum throughput of the link.
NT1150 ValidatorPRO Ethernet Speed Certifier w/Power Meter $1780.00
NT1155 ValidatorPRO-NT Ethernet Speed Certifier w/Power Meter & active network tests $2515.00
ValidatorPRO & ValidatorPRO-NT include:
smart remote, set 1-8 remotes (RJ11/RJ45)
(TP612), 2 lithium-ion rechargeable batteries
(NT93), 2 universal AC adapter/charger units,
1.83m (72in) USB client-to-PC connection cable
(series A plug to series B plug), two 19 cm (7.5
in) RJ12-to-RJ12 cables for no-fault connection
to RJ11 or RJ45 jacks, two 30.48 cm (1’) patch
cables with RJ45 connectors, two 60.96 cm (2’)
RJ45 to 8 alligator clips cord sets, 2 sacrificial
cables for RJ45 mod plug, one coupler F-jack to
F-jack, USB drive including Plan-Um® software,
user guide, Deluxe carrying case, 100 “speed
certified” cable labels, & 12V vehicle charger.
Accessories for ValidatorPRO and ValidatorPRO-NT Ethernet Speed Certifier
NT93 Lithium-ion rechargeable battery $74.65
NT94 1.83 m (72 in) USB cable assembly $6.80
NT95 Cable speed certified labels, roll of 100 $12.90
TP20 19 cm (7.5 in) RJ12-to-RJ12 cable for no-fault connection to RJ11 or RJ45 jacks $2.25
TP55 30.48 cm (1 ft) patch cable with RJ45 connectors $2.90
TP62 F-connector plug to BNC jack adapter $8.95
TP68 60.96 cm (2 ft) RJ45 to 8 alligator clips cord set $18.50
TP74 Sacrificial cable for RJ45 mod plug $27.85
TP311 Set of 20 (1–20) Coax ID-only remotes $52.00
TP312 Set of 20 (1-20) RJ45 ID-only remote identifiers $32.90
TP314 Set of 20 (1-20) RJ11 ID-only remote identifiers $32.90
2255/01 OLS-5 Optical MM LED Source 850/1300nm, ST connector type $850.00
2255/02 OLS-6 Optical SM Laser Source 1310/1550, FC connector type $1495.00
FBP-SM05-C Inspection & Cleaning Kit $2325.00
FBP-SM03-C Inspection & Cleaning Kit - same as FBP-SM05-C but with HD3 Display $2120.00
FFL-050 Visual Fault Locator - Pocket Size, 2.5mm (SM & MM) $160.00
FITP-UPP12 1.25mm UPP adapter $48.50
Validator & Validator-NT
The Validator offers a complete solution to test and speed certify the data-carrying capabilities of Ethernet
network cables up to 1 Gb/s by testing for noise in the network, detecting faults in the cabling wiring, and
ensuring that cables are able to support the speed capabilities of active equipment. The Validator can be
used as a cost-effective alternative to full TIA/ISO cable certification in environments where ensuring cable
runs support Ethernet speeds up to Gigabit Ethernet is adequate.
To certify Ethernet speed performance of cable runs, the Validator conducts Bit Error Rate (BER) tests by
sending data packets down specified cable runs at defined data rates to check for errors at the maximum
throughput of the link. The Validator also reports on signal quality that can impact high-speed data
transmission by measuring signal-to-noise ratio (SNR). Skew measurements report on the signal time delay
between pairs that can impact Ethernet data transmission. Finally, the Validator provides continuity testing
that detects opens, shorts, miswires, split pairs, reversals, and high-resistance faults while accurately
measuring distance to faults and total cable length.
Validator includes the powerful Plan-Um® planning and reporting software for planing network architectures
and organizing cable information and test results. Plan-Um helps set up each job, defines scope of the job,
aids in testing cable runs, and produces reports for the installer and customer. The Network Tools feature
provides a quick view to see the network architecture and a way to document moves, adds, and changes.
Used in conjunction with Plan-Um, Validator provides confidence in the physical properties of cable runs and
the overall capability of the network.
Validator & Validator-NT: include
a smart remote, 2 lithium rechargeable
batteries, 2 AC adapter/charger, 1.83m
(72”) USB cable assembly, compact
flash card, two 19cm (7.5”) RJ12 to RJ12
cables for no-fault connection to RJ11 or
RJ45 jacks, 2 F-Connector plug to BNC
jack adapters, two 30.48cm (1’) patch
cables with RJ45 connectors, two 60.96
cm (2’) RJ45 to 8 alligator clips cord sets,
2 sacrificial cables for RJ45 mod plug,
Plan-Um® software , and carrying case
NT950 Validator Cable Certification Kit $1330.00
NT955 Validator-NT Cable Certification Kit $1445.00
Accessories Validator & Validator NT Cable Certifiers
NT93 Lithium Ion Rechargeable Battery $74.65
NT94 1.83m (72 in) USB Cable Assembly $6.80
NT95 Cable Speed Certified Labels, roll of 100 $12.90
NT925 Smart Remote for Validator $215.00
NT928 Smart Remote for Validator-NT $215.00
TP20 19 cm (7.5 in) RJ12 to RJ12 cable for no-fault connection to RJ11 or RJ45 Jacks $2.85
TP55 30.48 cm (1 ft) Patch Cable with RJ45 Connectors $2.90
TP62 F-Connector Plug to BNC Jack Adapter $8.95
TP68 60.96 cm (2 ft) RJ45 to 8 alligator clips cord set $18.50
TP74 Sacrificial Cable for RJ45 Mod Plug $27.85
50
TM
Datacomtools.com
Free Ground Shipping on Orders over $99.00. In the contiguous states, certain items may not apply