AGCO Parts & Weasler Driveline Catalog

More documents

Recommendations

Info

SPROCKETS•HUBS•PULLEYS WELDiNg iNSTRUCTiONS: > Insert hub in sprocket plate or pulley blank > Hold the parts in place with a C-clamp > Tack weld in two places > Remove C-clamp and weld continuously around hub. Always weld on larger side of hub, except on smaller sprockets where the weld may interfere with chain clearance. USE OF SPROCKET, HUB, & PULLEY NUMBERiNg SYSTEM: Sprocket # Identification Example: 2000 50 12 Number of teeth Chain Size Sprocket Prefix Hub # Identification Example: V HUB W HUB X HUB XX HUB 200 100 08 200 200 08 200 300 10 200 400 16 SPROCKETS / HUBS AND PULLEYS * (Expressed in 1/16th inches) 1/2" Bore Size* 1/2" Bore Size* 5/8" Bore Size* 1" Bore Size* Hub Type Hub Type Hub Type Hub Type Hub Prefix Hub Prefix Hub Prefix Hub Prefix 188
Sprockets 35 Chain Fits V Series Hub Fits W Series Hub Stock Outside Number Teeth Diameter 20003515 15 2" 20003516 16 2 1/8" 20003517 17 2 1/4" 20003518 18 2 3/8" 20003519 19 2 1/2" 20003520 20 2 5/8" 20003521 21 2 3/4" Stock Outside Number Teeth Diameter 20003522 22 2 13/16" 20003523 23 2 15/16" 20003524 24 3 1/16" 20003525 25 3 3/16" 20003526 26 3 5/16" 20003527 27 3 7/16" 20003528 28 3 9/16" 20003529 29 3 11/16" 20003530 30 3 13/16" 20003532 32 4 1/16" Stock Outside Number Teeth Diameter 20003535 35 4 5/16" 20003536 36 4 1/2" 20003540 40 4 15/16" 20003545 45 5 9/16" 20003548 48 5 15/16" 20003560 60 7 5/16" 20003572 72 8 3/4" 20003584 84 10 1/4" 20003596 96 11 5/8" 40 Chain Fits V Series Hub Fits X Series Hub Stock Outside Number Teeth Diameter 20004012 12 2 3/16" 20004013 13 2 1/4" 20004014 14 2 7/16" 20004015 15 2 5/8" Fits W Series Hub Stock Outside Number Teeth Diameter 20004016 16 2 13/16" 20004017 17 3" 20004018 18 3 1/8" 20004019 19 3 5/16" Stock Outside Number Teeth Diameter 20004020 20 3 7/16" 20004021 21 3 5/8" 20004022 22 3 3/4" 20004023 23 4" 20004024 24 4 1/16" 20004025 25 4 3/16" 20004026 26 4 3/8" 20004027 27 4 1/2" 20004028 28 4 11/16" 20004029 29 4 3/4" 20004030 30 5 1/16" 20004032 32 5 3/8" Stock Outside Number Teeth Diameter 20004035 35 5 11/16" 20004036 36 6" 20004038 38 6 /14" 20004040 40 6 5/8" 20004042 42 7" 20004045 45 7 3/8" 20004048 48 7 7/8" 20004054 54 8 7/8" 20004060 60 9 3/16" 20004072 72 11 3/16" 20004080 80 12 15/16" 20004096 96 15 1/2" * NOTE: All measurements of outside diameters are approximate. SPROCKETS / HUBS AND PULLEYS 189
Page 2 and 3:
AGCO Parts is your source for Weasl
Page 4 and 5:
Weasler ® I N D E X CONStaNt velOC
Page 6 and 7:
SAFETY SECTION SAFETY 2SECTION Warn
Page 8 and 9:
GREASING RECOMMENDATIONS SAFETY SEC
Page 10 and 11:
DRIVELINE LENGTH ADJUSTMENT SAFETY
Page 12 and 13:
CROSS REFERENCE CHART NORTH AMERICA
Page 14 and 15:
Constant Velocity Cross & Bearing K
Page 16 and 17:
UNIVERSAL JOINT REPLACEMENT to diSA
Page 18 and 19:
EASY LOCK gUARDINg SYSTEM METRIC in
Page 20 and 21:
EASY LOCK gUARDINg SYSTEM PRevioUS-
Page 22 and 23:
Locking Device Safety Slide Lock An
Page 24 and 25:
N O T E S QUICK REFERENCE SECTION 2
Page 26 and 27:
N O T E S replacement drivelines 22
Page 28 and 29:
CONSTANT VELOCITY DRIVELINES north
Page 30 and 31:
CONSTANT VELOCITY DRIVELINES...cont
Page 32 and 33:
NEW! REPLACEMENT WING DRIVE SHAFTS
Page 34 and 35:
CONSTANT VELOCITY DRIVELINES...cont
Page 36 and 37:
METRIC DRIVELINES interchange with
Page 38 and 39:
METRIC DRIVELINES...continued inter
Page 40 and 41:
NORTH AMERICAN DRIVELINES •ALL PU
Page 42 and 43:
CONSTANT VELOCITY - NORTH AMERICAN.
Page 44 and 45:
N O T E S replacement drivelines 40
Page 46 and 47:
Each series has an exploded view fo
Page 48 and 49:
2 9/32" (2.28) 6 Series 31/32" (.97
Page 50 and 51:
6 Series (cont’d.) Implement Yoke
Page 52 and 53:
6 Series (cont’d.) Universal Join
Page 54 and 55:
12 Series (cont’d.) Shaft Weld Yo
Page 56 and 57:
12 Series (cont’d.) Universal Joi
Page 58 and 59:
14 Series (cont’d.) Cross & Beari
Page 60 and 61:
14 Series (cont’d.) Guard Order B
Page 62 and 63:
3 7/32" (3.22) 35 Series 1 1/4" (1.
Page 64 and 65:
35 Series (cont’d.) Implement Yok
Page 66 and 67:
35 Series (cont’d.) Drivelines A
Page 68 and 69:
44 Series (cont’d.) Cross & Beari
Page 70 and 71:
44 Series (cont’d.) Guard Stock N
Page 72 and 73:
4 5/16" (4.31) 55 Series 1 17/32" (
Page 74 and 75:
55 Series (cont’d.) Tube Weld Yok
Page 76 and 77:
1 1/2" (1.5) W Series 9/16" ( .56)
Page 78 and 79:
2 5/16" (2.31) 0675 Series Intercha
Page 80 and 81:
1000 Series (cont’d.) Interchange
Page 82 and 83:
1800 Series Interchanges with Neapc
Page 84 and 85:
2600 Series (cont’d.) Tube Weld Y
Page 86 and 87:
Nylon Bearing Repair Kit (Kit inclu
Page 88 and 89:
N O T E S N.A. DRIVELINE & COMPONEN
Page 90 and 91:
METRIC DRIVELINES & COMPONENTS TRAN
Page 92 and 93:
METRIC DRIVELINES & COMPONENTS 2 1/
Page 94 and 95:
METRIC DRIVELINES & COMPONENTS 1 Se
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
METRIC DRIVELINES & COMPONENTS 3 45
Page 112 and 113:
METRIC DRIVELINES & COMPONENTS 7N S
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
METRIC DRIVELINES & COMPONENTS Inne
Page 122 and 123:
METRIC DRIVELINES & COMPONENTS Inne
Page 124 and 125:
METRIC DRIVELINES & COMPONENTS I Se
Page 126 and 127:
METRIC DRIVELINES & COMPONENTS 2300
Page 128 and 129:
Page 130 and 131:
METRIC DRIVELINES & COMPONENTS 3" (
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
METRIC DRIVELINES & COMPONENTS 3 35
Page 140 and 141:
METRIC DRIVELINES & COMPONENTS Metr
Page 142 and 143: METRIC DRIVELINES & COMPONENTS Metr
Page 144 and 145: METRIC DRIVELINES & COMPONENTSN O T
Page 146 and 147: 80° Constant Velocity Driveline Wi
Page 148 and 149: n o T e S CONSTANT VELOCITY 144
Page 150 and 151: 80° CV Category 3 / 14 Series...co
Page 152 and 153: 80° CV Category 4 / 35 Series Trac
Page 156 and 157: 80° CV Category 5 / 35/44 Series..
Page 158 and 159: 80° CV Category 6 / 55 Series Trac
Page 162 and 163: 50° Constant Velocity Driveline Co
Page 164 and 165: 2380 Series Outer Profile Yoke 80°
Page 166 and 167: 2480 Series (cont’d.) Outer Tube
Page 168 and 169: 2580 Series Interchanges with Walte
Page 170 and 171: 2580 Series Guard Bearings supplied
Page 172 and 173: Metric Replacement Driveline APPLIC
Page 174 and 175: 80º CV rounD BALer DrIVeLIneS CONS
Page 176 and 177: CLUTCHES NORTH AMERICAN Weasler 14,
Page 178 and 179: Assembly Instructions for the Modul
Page 180 and 181: Clutch Pak Selection Guide Rotary C
Page 182 and 183: Clutch Components 35 Series continu
Page 184 and 185: Clutch Components metric SectioN Cl
Page 186 and 187: Clutch Components Interchanges with
Page 188 and 189: Clutch Components Universal Frictio
Page 190 and 191: N O T E S CLUTCHES 186
Page 194 and 195: Sprockets 50 Chain Fits V Series Hu
Page 196 and 197: Roller Chain idler Sprockets 40 Cha
Page 198 and 199: Hubs (cont’d.) X Series XX Series
Page 200 and 201: N O T E S SPROCKETS / HUBS AND PULL
Page 202 and 203: JAW COUPLINGS Jaw Couplings ROUND B
Page 204 and 205: NORTH AMERICAN & METRIC E-KIT DISPL
Page 206 and 207: NORTH AMERICAN DRIVELINE COMPONENT
Page 208 and 209: METRIC DRIVELINE COMPONENT DISPLAY
Page 210 and 211: Display Components #40 Sprocket #50
show all

AGCO Parts & Weasler Driveline Catalog

Create successful ePaper yourself

Delete template?

Save as template?