AGCO Parts & Weasler Driveline Catalog
AGCO Parts & Weasler Driveline Catalog AGCO Parts & Weasler Driveline Catalog
DRIVELINE LENGTH ADJUSTMENT SAFETY 6SECTION Replacement Driveline 1 2 Remove guard from driveline. Separate driveline halves. Shorten guard halves (Pic. 1) and profile tube halves (Pic. 2) same as existing driveline halves or see example below. 4 5 6 Grease sliding profiles. 48" (A) 42" (B) Existing Driveline Round off all sharp edges and remove burrs. Reassemble guard halves. Both profile tubes should extend 40-mm (1.58") beyond the end of the guard tubes. Reassemble driveline halves together making sure they slide (telescope) easily and ensure guards rotate freely on yokes. EXAMPLE: If overall replacement driveline length dimension is 48" (See A), and your existing overall driveline length dimension is 42" (See B), the amount to shorten EACH driveline half would be 6". Your driveline is now ready to reassemble and use. 3
AFTERMARKET PRODUCT GUIDE QUICK REFERENCE QUICK REFERENCE SECTION 7
- Page 2 and 3: AGCO Parts is your source for Weasl
- Page 4 and 5: Weasler ® I N D E X CONStaNt velOC
- Page 6 and 7: SAFETY SECTION SAFETY 2SECTION Warn
- Page 8 and 9: GREASING RECOMMENDATIONS SAFETY SEC
- Page 12 and 13: CROSS REFERENCE CHART NORTH AMERICA
- Page 14 and 15: Constant Velocity Cross & Bearing K
- Page 16 and 17: UNIVERSAL JOINT REPLACEMENT to diSA
- Page 18 and 19: EASY LOCK gUARDINg SYSTEM METRIC in
- Page 20 and 21: EASY LOCK gUARDINg SYSTEM PRevioUS-
- Page 22 and 23: Locking Device Safety Slide Lock An
- Page 24 and 25: N O T E S QUICK REFERENCE SECTION 2
- Page 26 and 27: N O T E S replacement drivelines 22
- Page 28 and 29: CONSTANT VELOCITY DRIVELINES north
- Page 30 and 31: CONSTANT VELOCITY DRIVELINES...cont
- Page 32 and 33: NEW! REPLACEMENT WING DRIVE SHAFTS
- Page 34 and 35: CONSTANT VELOCITY DRIVELINES...cont
- Page 36 and 37: METRIC DRIVELINES interchange with
- Page 38 and 39: METRIC DRIVELINES...continued inter
- Page 40 and 41: NORTH AMERICAN DRIVELINES •ALL PU
- Page 42 and 43: CONSTANT VELOCITY - NORTH AMERICAN.
- Page 44 and 45: N O T E S replacement drivelines 40
- Page 46 and 47: Each series has an exploded view fo
- Page 48 and 49: 2 9/32" (2.28) 6 Series 31/32" (.97
- Page 50 and 51: 6 Series (cont’d.) Implement Yoke
- Page 52 and 53: 6 Series (cont’d.) Universal Join
- Page 54 and 55: 12 Series (cont’d.) Shaft Weld Yo
- Page 56 and 57: 12 Series (cont’d.) Universal Joi
- Page 58 and 59: 14 Series (cont’d.) Cross & Beari
DRIVELINE LENGTH ADJUSTMENT<br />
SAFETY<br />
6SECTION<br />
Replacement <strong>Driveline</strong><br />
1 2<br />
Remove guard from driveline. Separate driveline<br />
halves. Shorten guard halves (Pic. 1) and profile<br />
tube halves (Pic. 2) same as existing driveline<br />
halves or see example below.<br />
4 5<br />
6<br />
Grease sliding<br />
profiles.<br />
48" (A) 42" (B)<br />
Existing <strong>Driveline</strong><br />
Round off all sharp<br />
edges and remove<br />
burrs.<br />
Reassemble guard halves. Both profile<br />
tubes should extend 40-mm (1.58") beyond<br />
the end of the guard tubes.<br />
Reassemble driveline halves together making sure they slide (telescope) easily<br />
and ensure guards rotate freely on yokes.<br />
EXAMPLE: If overall replacement driveline length dimension is 48" (See A), and your existing overall<br />
driveline length dimension is 42" (See B), the amount to shorten EACH driveline half would be 6".<br />
Your driveline is now ready to reassemble and use.<br />
3
Change language