Controllers - AGCO Parts
Controllers - AGCO Parts Controllers - AGCO Parts
Pumps Banjo Cast Iron Pumps Banjo cast iron centrifugal pumps provide quality you can depend on. Pumps are self priming and are available in a broad range of sizes from 1½" 3-h.p. to 3" 11-h.p. Features such as stainless steel shaft sleeve to protect engine shaft, carbon ceramic seal with stainless steel housing are standard. Rubber parts are made of EPDM for better resistance to agricultural chemicals. The 2" pump (200PIH5) has the 5-h.p. Honda engine, the 3" pump (300PI11) has 11-h.p. Honda with electric start. Honda engines boast features like overhead valves, *Oil AlertTM which automatically stops engine if oil drops below a safe level, and ball bearing supported crankshaft. Convenience features such as dual oil drains and fillers are standard. Note: Oil AlertTM not available on 11 HP model. | Part | Description | | AG007178 | Pump 1-1/2" - 3HP Briggs - 100 GPM | | AG007126 | Pump 2" - 3 HP Briggs - 160 GPM | | AG005619 | Pump 2" - 5HP Briggs OHV - 160 GPM | | AG008419 | Pump 2" - 5 HP Honda - 160 GPM | | AG060324 | Pump 2" with 6HP Vangaurd 160 GPM | | AG717760 | Pump 3" - 8 HP Honda Electric Start | | AG007920 | Pump 3" - 11 HP Honda Electric Start - 250 GPM | | AG007124 | Pump 2" Less Engine | | AG007918 | Pump 3" Less Engine | | AG007177 | Pedestal Pump 2" Cast Iron - 3/4" Shaft | | AG007919 | Pedestal Pump 3" Cast Iron - 1" Shaft | | AG057557 | Pedestal Assembly for 1-1/2 & 2" - 3/4" Shaft | | AG008567 | Pedestal Assembly for 3" - 1"" Shaft | Banjo Cast Iron Pump Repair Parts Notes: * = For 1-1/2" and 2" Pumps. ** = For 3" Pumps. AG553441 is a 1/4" Drain plug. | Ref | Part |Description | | 1 | AG006213 | Flange, Outlet 2"* | | 1** | AG008574 | Flange, Outlet** | | 2 | AG005793 | Flange, Inlet 20°, 2"* | | 2** | AG008580 | Flange, Inlet** | | 3 | AG006597 | Adapter, Gas Engine* | | 3** | AG008570 | Adapter, Gas Engine** | | 4 | AG007127 | Sleeve Drive, 5/8" * | | 4** | AG005614 | Sleeve Drive, 3/4"* | | 4 | AG007128 | Sleeve Drive, 7/8"* | | 5 | AG005612 | Impeller* | | 5** | AG008572 | Impeller** | | 7 | AG007130 | Nut, Hex, 1/2-13 UNC* | | 7** | AG050130 | Nut, Hex 1/2-13 UNC** | | 8 | AG005613 | Wear Plate* | | 8** | AG008576 | Wear Plate** | | 9 | AG005904 | EPDM Gasket* | | 9** | AG008579 | EPDM Gasket** | | 10 | AG006228 | Gasket-Check Valve* | | 10** | AG008581 | Gasket, Check Valve** | | 11 | AG005611 | Gasket Adapter, 2" | | 11** | AG008573 | Gasket Adapter, 3" | | 12 | AG007123 | Cap Screw, 5/16"-18 x 3/4, 2" | | 13** | AG050132 | Handle, 3" | | 14 | AG007166 | Clamp, 5/8", 3/4" Shaft (old style)* | | 14 | AG007121 | Clamp, 7/8" Shaft (old style) | | 14 | AG058885 | Clamp, 5/8", 3/4" Shaft* (new style keyed) | | 14** | AG058536 | Clamp** (new style keyed) | | 15 | AG007120 | Wear Plate Gasket, 2" | | 15** | AG008577 | Wear Plate Gasket, 3" | | 16 | AG005795 | Pump Housing* | | 16** | AG008575 | Pump Housing** | | 17 | AG007119 | S.S. Acorn Nut 5/16-18, 2" | | 19 | AG007117 | Flat Head 80°C Screw* | | 19** | AG009384 | Flat Head 82°C Screw** | | 21** | AG553441 | 1/4" | | 22 | AG007115 | Hex Nut, 2" | | 23 | AG007114 | Brg. Shaft Assembly/Shaft, 2"* | | 23** | AG008563 | Shaft Assembly/Shaft 3"** | | 24 | AG057557 | Pedestal Assembly for 1-1/2 & 2" - 3/4 " Shaft | | 24** | AG008567 | Pedestal Assembly for 3" - 1" Shaft | | 25** | AG050136 | Cap Screw, 15/16-24-NF** | | 26 | AG005610 | Seal Assembly, Viton* | | 26** | AG008571 | Seal Assembly, Viton** | 88
Type 316 Stainless Steel Pedestal Pumps These pumps look and perform exactly like the rugged cast iron models only all the wetted parts are made of type 316 stainless steel for maximum corrosion resistance. | Part | Description | | AG053093 | 2" Pump with Pedestal | | AG053091 | 3" Pump with Pedestal | Type 316 Stainless Steel Pump Repair Parts Banjo 222 Series Banjo's 222 series cast iron pumps have more horsepower to deliver flows up to 225 GPM. They are well suited for agricultural pumps, contractor pumps, and emergency uses (fires and floods). The 6.5 HP Intek Pro series motor features oil guard oil sensor, cast iron cylinder sleeve, high efficiency OHV design, and a super low-tone muffler. Pump Features: • Durable cast iron construction • Replaceable inlet and outlet flanges • Carbon ceramic seal with stainless steel cup and spring Note: Pump only requires 3/4" straight keyed shaft engine. | Part | Description | | AG725943 | Pump 2" Cast Iron with 6.5 HP Intek | | AG058539 | Pump 2" Cast Iron with 5.5 HP Honda | | AG726068 | Pump 2" Cast Iron with 5.5 HP Honda E/Start | | AG060206 | Pump 2" Cast Iron with 6.5 HP Honda | | AG726069 | Pump 2" Cast Iron with 6 HP Vanguard | | AG726062 | Pump Only 2" Cast Iron | | Ref | Part |Description | | 1 | AG053115 | Outlet Flange, 2" | | 2 | AG053114 | Inlet Flange, 2" | | 2 | AG053100 | Inlet Flange, 3" | | 5 | AG053111 | Impeller, 2" | | 5 | AG053095 | Impeller Assembly, 3" | | 8 | AG053110 | Wear Plate, 2" | | 8 | AG053103 | Wear Plate, 3" | | 9 | AG053107 | Gasket, 2" | | 9 | AG053096 | Gasket, 3" | | 10 | AG053106 | Check Valve, 2" | | 10 | AG053097 | Check Valve, 3" | | 11 | AG005611 | Gasket Adapter, 2" | | 11 | AG008573 | Gasket Adapter, 3" | | 12 | AG007123 | Cap Screw, 5/16"-18 x 3/4, 2" | | 12 | AG050131 | Cap Screw, 3" | | 13 | AG050132 | Handle, 3" | | 14 | AG007166 | Clamp, 5/8", 3/4" Shaft (old style) | | 14 | AG007121 | Clamp, 7/8" Shaft (old style) | | 14 | AG058885 | Clamp, 5/8", 3/4" Shaft (new style keyed) | | 14 | AG058536 | Clamp** (new style keyed) | | 15 | AG007120 | Wear Plate Gasket, 2" | | 15 | AG008577 | Wear Plate Gasket, 3" | | 16 | AG053109 | Housing, 2" | | 17 | AG007119 | S.S. Acorn Nut 5/16-18, 2" | | 19 | AG053105 | Screw, 2" | | 22 | AG007115 | Hex Nut, 2" | | 22 | AG057557 | Pedestal Assm. for 1-1/2 & 2" - 3/4" Shaft | | 24 | AG008567 | Pedestal Assembly, 3" - 1" Shaft | | 26 | AG053108 | Seal, 2" | | 26 | AG053099 | Seal, 3" | Banjo 333 Series Banjo's 333 series pump will deliver flow rates up to 515 GPM. Pump Features: • Durable cast iron construction • Dynamically balanced impeller • Replaceable inlet and outlet flanges • Graphite loaded silicon carbide seal with stainless steel cup and spring | Part | Description | | AG426504 | Pump 3" with 13 HP Honda | Banjo 444 Series Banjo's 444 series self-priming 4" cast iron centrifugal pump will deliver up to 650 gallons per minute. Features: • Durable cast iron construction • Dynamically balanced impeller • Replaceable inlet and outlet flanges • V shaped for quicker priming • Graphite loaded silicon carbide seal with stainless steel cup | Part | Description | | AG725944 | Pump 4" with 18 HP Kohler | | AG426503 | Pump 4" with 24 HP Honda | Pumps 89
- Page 39 and 40: SCS-Sidekick Direct Injection Syste
- Page 41 and 42: Raven Control Cables | Part | Descr
- Page 43 and 44: Calc-An-Acre II The Calc-An-Acre II
- Page 45 and 46: RFM60S Flowmeter RFM100 Repair Part
- Page 47 and 48: RFM400 Repair Parts Accu-Flow Kits
- Page 49 and 50: CCS100 Custom Control System Liquid
- Page 51 and 52: CCS100 Flow Sensor Provides informa
- Page 53 and 54: AA144A DirectoValve Repair Parts No
- Page 55 and 56: Raven ® Electric Shut-Off Valves 1
- Page 57 and 58: QC3-Stack Valves Stack up to 10 val
- Page 59 and 60: Polypropylene Union Ball Valve A qu
- Page 61 and 62: All Stainless Steel Valves A qualit
- Page 63 and 64: Centerline Butterfly Valves Notes:
- Page 65 and 66: ACE 150 Series Repair Parts Note: V
- Page 67 and 68: ACE FMC-HYD Repair Parts Repair Par
- Page 69 and 70: SpraCoupe Replacement Pump Ace's ne
- Page 71 and 72: PTO Belt Driven Pumps Cast iron 1-1
- Page 73 and 74: Hypro Series 9303P Pumps Hydraulica
- Page 75 and 76: 9000 Series Centrifugal Pump Repair
- Page 77 and 78: Torque Bar and Chain Anchors pump d
- Page 79 and 80: Hypro D135 Diaphragm Pump Hypro low
- Page 81 and 82: 6500 Series Roller Pump • Max flo
- Page 83 and 84: Hydraulically-Driven Pressure Washe
- Page 85 and 86: 12V Motor Speed Control Controller
- Page 87 and 88: Repair Parts for Scot 2" Pump Scot
- Page 89: Ace GE-Series Pumps Ace's GE-Series
- Page 93 and 94: Pacer Hand Pump Heavy-duty, double-
- Page 95 and 96: GREEN XLPE for Chemical Transfer Fo
- Page 97 and 98: Dry Poppet Coupling Type B Female c
- Page 99 and 100: Viton Gaskets Note: AG009979 gasket
- Page 101 and 102: 45° and 90° Street Elbows Couplin
- Page 103 and 104: Coupling Flanged Y 45° Note: Full
- Page 105 and 106: Garden Hose Fittings Swivel Barbs M
- Page 107 and 108: 90° Elbows 45° St. Elbows Malleab
- Page 109 and 110: Type 304 Stainless Steel Fittings-
- Page 111 and 112: Air Couplings Allow fast, easy conn
- Page 113 and 114: Polypropylene “Y” Strainers •
- Page 115 and 116: Model 126 Strainers 1-1/4", 1-1/2",
- Page 117 and 118: Model 124 1-1/2" Strainer Parts Hyp
- Page 119 and 120: In-Line Strainer 3/4" NPT inlet, br
- Page 121 and 122: INSECTICIDES TEEJET CONTACT SYSTEMI
- Page 123 and 124: Spray Tips 121
- Page 125 and 126: Turbo TeeJet ® Spray Tips Typical
- Page 127 and 128: Turbo TwinJet ® Typical Applicatio
- Page 129 and 130: 80° XRVS TeeJet Spray Tips Caps fo
- Page 131 and 132: XRC Tip and Cap Combination Extende
- Page 133 and 134: Hypro Ultra Lo-Drift Nozzles The Ul
- Page 135 and 136: Hypro Guardian Spray Tips Guardian
- Page 137 and 138: 80° VisiFlo Spray Tips • The tip
- Page 139 and 140: Drift Guard Twin Jet DG TeeJet Drif
Type 316 Stainless Steel Pedestal Pumps<br />
These pumps look and perform exactly like the rugged cast iron models<br />
only all the wetted parts are made of type 316 stainless steel for maximum<br />
corrosion resistance.<br />
| Part | Description |<br />
| AG053093 | 2" Pump with Pedestal |<br />
| AG053091 | 3" Pump with Pedestal |<br />
Type 316 Stainless Steel Pump Repair <strong>Parts</strong><br />
Banjo 222 Series<br />
Banjo's 222 series cast iron pumps have<br />
more horsepower to deliver flows up to<br />
225 GPM. They are well suited for agricultural<br />
pumps, contractor pumps, and<br />
emergency uses (fires and floods). The<br />
6.5 HP Intek Pro series motor features<br />
oil guard oil sensor, cast iron cylinder<br />
sleeve, high efficiency OHV design, and<br />
a super low-tone muffler.<br />
Pump Features:<br />
• Durable cast iron construction<br />
• Replaceable inlet and outlet flanges<br />
• Carbon ceramic seal with stainless<br />
steel cup and spring<br />
Note: Pump only requires 3/4" straight<br />
keyed shaft engine.<br />
| Part | Description |<br />
| AG725943 | Pump 2" Cast Iron with 6.5 HP Intek |<br />
| AG058539 | Pump 2" Cast Iron with 5.5 HP Honda |<br />
| AG726068 | Pump 2" Cast Iron with 5.5 HP Honda E/Start |<br />
| AG060206 | Pump 2" Cast Iron with 6.5 HP Honda |<br />
| AG726069 | Pump 2" Cast Iron with 6 HP Vanguard |<br />
| AG726062 | Pump Only 2" Cast Iron |<br />
| Ref | Part |Description |<br />
| 1 | AG053115 | Outlet Flange, 2" |<br />
| 2 | AG053114 | Inlet Flange, 2" |<br />
| 2 | AG053100 | Inlet Flange, 3" |<br />
| 5 | AG053111 | Impeller, 2" |<br />
| 5 | AG053095 | Impeller Assembly, 3" |<br />
| 8 | AG053110 | Wear Plate, 2" |<br />
| 8 | AG053103 | Wear Plate, 3" |<br />
| 9 | AG053107 | Gasket, 2" |<br />
| 9 | AG053096 | Gasket, 3" |<br />
| 10 | AG053106 | Check Valve, 2" |<br />
| 10 | AG053097 | Check Valve, 3" |<br />
| 11 | AG005611 | Gasket Adapter, 2" |<br />
| 11 | AG008573 | Gasket Adapter, 3" |<br />
| 12 | AG007123 | Cap Screw, 5/16"-18 x 3/4, 2" |<br />
| 12 | AG050131 | Cap Screw, 3" |<br />
| 13 | AG050132 | Handle, 3" |<br />
| 14 | AG007166 | Clamp, 5/8", 3/4" Shaft (old style) |<br />
| 14 | AG007121 | Clamp, 7/8" Shaft (old style) |<br />
| 14 | AG058885 | Clamp, 5/8", 3/4" Shaft (new style keyed) |<br />
| 14 | AG058536 | Clamp** (new style keyed) |<br />
| 15 | AG007120 | Wear Plate Gasket, 2" |<br />
| 15 | AG008577 | Wear Plate Gasket, 3" |<br />
| 16 | AG053109 | Housing, 2" |<br />
| 17 | AG007119 | S.S. Acorn Nut 5/16-18, 2" |<br />
| 19 | AG053105 | Screw, 2" |<br />
| 22 | AG007115 | Hex Nut, 2" |<br />
| 22 | AG057557 | Pedestal Assm. for 1-1/2 & 2" - 3/4" Shaft |<br />
| 24 | AG008567 | Pedestal Assembly, 3" - 1" Shaft |<br />
| 26 | AG053108 | Seal, 2" |<br />
| 26 | AG053099 | Seal, 3" |<br />
Banjo 333 Series<br />
Banjo's 333 series pump will deliver flow<br />
rates up to 515 GPM.<br />
Pump Features:<br />
• Durable cast iron construction<br />
• Dynamically balanced impeller<br />
• Replaceable inlet and outlet flanges<br />
• Graphite loaded silicon carbide seal with<br />
stainless steel cup and spring<br />
| Part | Description |<br />
| AG426504 | Pump 3" with 13 HP Honda |<br />
Banjo 444 Series<br />
Banjo's 444 series self-priming 4" cast iron<br />
centrifugal pump will deliver up to 650 gallons<br />
per minute.<br />
Features:<br />
• Durable cast iron construction<br />
• Dynamically balanced impeller<br />
• Replaceable inlet and outlet flanges<br />
• V shaped for quicker priming<br />
• Graphite loaded silicon carbide seal with<br />
stainless steel cup<br />
| Part | Description |<br />
| AG725944 | Pump 4" with 18 HP Kohler |<br />
| AG426503 | Pump 4" with 24 HP Honda |<br />
Pumps<br />
89