Controllers - AGCO Parts

Pumps
Banjo Cast Iron Pumps
Banjo cast iron centrifugal pumps
provide quality you can depend on.
Pumps are self priming and are available
in a broad range of sizes from
1½" 3-h.p. to 3" 11-h.p. Features
such as stainless steel shaft sleeve
to protect engine shaft, carbon
ceramic seal with stainless steel
housing are standard. Rubber parts are made of EPDM for better resistance
to agricultural chemicals.
The 2" pump (200PIH5) has the 5-h.p. Honda engine, the 3" pump
(300PI11) has 11-h.p. Honda with electric start. Honda engines boast
features like overhead valves, *Oil AlertTM which automatically stops
engine if oil drops below a safe level, and ball bearing supported crankshaft.
Convenience features such as dual oil drains and fillers are standard.
Note: Oil AlertTM not available on 11 HP model.
| Part | Description |
| AG007178 | Pump 1-1/2" - 3HP Briggs - 100 GPM |
| AG007126 | Pump 2" - 3 HP Briggs - 160 GPM |
| AG005619 | Pump 2" - 5HP Briggs OHV - 160 GPM |
| AG008419 | Pump 2" - 5 HP Honda - 160 GPM |
| AG060324 | Pump 2" with 6HP Vangaurd 160 GPM |
| AG717760 | Pump 3" - 8 HP Honda Electric Start |
| AG007920 | Pump 3" - 11 HP Honda Electric Start - 250 GPM |
| AG007124 | Pump 2" Less Engine |
| AG007918 | Pump 3" Less Engine |
| AG007177 | Pedestal Pump 2" Cast Iron - 3/4" Shaft |
| AG007919 | Pedestal Pump 3" Cast Iron - 1" Shaft |
| AG057557 | Pedestal Assembly for 1-1/2 & 2" - 3/4" Shaft |
| AG008567 | Pedestal Assembly for 3" - 1"" Shaft |
Banjo Cast Iron Pump Repair Parts
Notes: * = For 1-1/2" and 2" Pumps. ** = For 3" Pumps. AG553441
is a 1/4" Drain plug.
| Ref | Part |Description |
| 1 | AG006213 | Flange, Outlet 2"* |
| 1** | AG008574 | Flange, Outlet** |
| 2 | AG005793 | Flange, Inlet 20°, 2"* |
| 2** | AG008580 | Flange, Inlet** |
| 3 | AG006597 | Adapter, Gas Engine* |
| 3** | AG008570 | Adapter, Gas Engine** |
| 4 | AG007127 | Sleeve Drive, 5/8" * |
| 4** | AG005614 | Sleeve Drive, 3/4"* |
| 4 | AG007128 | Sleeve Drive, 7/8"* |
| 5 | AG005612 | Impeller* |
| 5** | AG008572 | Impeller** |
| 7 | AG007130 | Nut, Hex, 1/2-13 UNC* |
| 7** | AG050130 | Nut, Hex 1/2-13 UNC** |
| 8 | AG005613 | Wear Plate* |
| 8** | AG008576 | Wear Plate** |
| 9 | AG005904 | EPDM Gasket* |
| 9** | AG008579 | EPDM Gasket** |
| 10 | AG006228 | Gasket-Check Valve* |
| 10** | AG008581 | Gasket, Check Valve** |
| 11 | AG005611 | Gasket Adapter, 2" |
| 11** | AG008573 | Gasket Adapter, 3" |
| 12 | AG007123 | Cap Screw, 5/16"-18 x 3/4, 2" |
| 13** | AG050132 | Handle, 3" |
| 14 | AG007166 | Clamp, 5/8", 3/4" Shaft (old style)* |
| 14 | AG007121 | Clamp, 7/8" Shaft (old style) |
| 14 | AG058885 | Clamp, 5/8", 3/4" Shaft* (new style keyed) |
| 14** | AG058536 | Clamp** (new style keyed) |
| 15 | AG007120 | Wear Plate Gasket, 2" |
| 15** | AG008577 | Wear Plate Gasket, 3" |
| 16 | AG005795 | Pump Housing* |
| 16** | AG008575 | Pump Housing** |
| 17 | AG007119 | S.S. Acorn Nut 5/16-18, 2" |
| 19 | AG007117 | Flat Head 80°C Screw* |
| 19** | AG009384 | Flat Head 82°C Screw** |
| 21** | AG553441 | 1/4" |
| 22 | AG007115 | Hex Nut, 2" |
| 23 | AG007114 | Brg. Shaft Assembly/Shaft, 2"* |
| 23** | AG008563 | Shaft Assembly/Shaft 3"** |
| 24 | AG057557 | Pedestal Assembly for 1-1/2 & 2" - 3/4 " Shaft |
| 24** | AG008567 | Pedestal Assembly for 3" - 1" Shaft |
| 25** | AG050136 | Cap Screw, 15/16-24-NF** |
| 26 | AG005610 | Seal Assembly, Viton* |
| 26** | AG008571 | Seal Assembly, Viton** |
88