Controllers - AGCO Parts

Ace GE-Series Pumps
Ace's GE-Series pump
provides service where
power sources are limited
or unavailable including
skid mount and ATV units.
The pumps are ideally
suited for liquid transfer
or spray-transfer combinations. Pumps feature cast iron construction,
easily replaceable mechanical seal, stainless steel sleeve to protect
engine shaft, and slinger ring between pump seal and engine bearings
to prevent liquid from entering engine. The pump and engine are fully
assembled ready to install and run.
GE-650/660:
• 1-1/2" Suction x 1-1/4" Discharge
• Max pressure: 120 PSI
• Max flow: 110 GPM
• 650 mounts to 5/8" UNF threaded engine shaft
• 660 mounts to 3/4" keyed engine shaft
GE-800/860:
• 2" Suction x 1-1/2" Discharge
• Max pressure: 140 PSI
• Max flow: 140 GPM
• 850 mounts to 1" UNF threaded engine shaft
• 860 mounts to 1" keyed engine shaft
Banjo Poly Pedestal Pumps
Poly pedestal pumps may be direct coupled to a
3450 RPM high-speed electric motor or driven by
belt and pulley. A 3/4" keyed shaft is standard.
Note: Coupler not included.
| Part | Description |
| AG002456 | Pump, 2" |
| AG057191 | Pump, 3" |
Banjo Poly Pump Repair Parts
Repair parts for pumps made after September 1996. These parts are for 1-1/2",
2", and 3" pumps, unless otherwise noted.
Notes: * = Repair Kit Items. (**) = This part may not be shown in this exploded
view drawing. (a) = For 1-1/2" Pumps. (b) = For 2" Pumps. (c) = For 3" Pumps #
AG057551 O-Ring prime drain plug (2 per pump) (C).
| Part | Description |
| AG057186 | GE-650 Pump with 5.5 HP Honda, threaded shaft |
| AG055760 | GE-650 Pump less engine, threaded shaft |
| AG427229 | GE-660 Pump less engine, keyed shaft |
| AG726015 | GE-800 Pump with 8 HP Honda, threaded shaft |
| AG427230 | GE-860 Pump less engine, keyed shaft |
Banjo Engine Driven Poly Pumps
The new improved design of this
poly pump sets it apart from the
competition. A new rear bracket
design now features a weep hole so
if seal failure occurs, it can easily be
seen and repaired. Seal failure that
goes undetected can often lead to
premature engine failure.
• New V-shaped body for faster priming
• New high-performance, precision-molded impellers
• New thumb screw drain and prime plugs
• New heavy-duty motor shaft slinger
| Part | Description |
| AG000809 | 1-1/2" with 3HP Briggs and Stratton 100 GPM |
| AG426805 | 2" with 6HP LCT Engine |
| AG426806 | 2" with 6.5HP Intec Pro |
| AG000940 | 2" with 3HP Briggs and Stratton 100 GPM |
| AG426806 | 2" with 6.5HP Intec Pro |
| AG008159 | 2" with 5HP Honda 160 GPM |
| AG057723 | 2" with 5.5HP Elec. Start Honda 160 GPM |
| AG060322 | 2" with 6HP Vanguard 160 GPM |
| AG057192 | 3" with 6.5HP Honda 320 GPM |
| AG060323 | 3" with 6HP Vanguard 320 GPM |
| AG007488 | Pump Only 1-1/2" |
| AG007487 | Pump Only 2" |
| AG057190 | Pump Only 3" |
| AG008333 | Engine 5.5 HP Honda 3/4" Keyed Shaft |
| AG000671 | Engine Only - 5 HP Briggs and Stratton Keyed Shaft |
| Ref | Part |Description |
| 2 | AG055330 | Body Nuts, S.S., (10 per pump) |
| 3 | AG055331 | Lock Washer, S.S. |
| 4 | AG055323 | Rear Bracket, New |
| 5,6** | AG000741 | Seal Assembly* |
| 7** | AG000744 | Screw Head O-Ring, (4 per pump)* |
| 8 | AG055322 | Bracket Screw, S.S. (4 per pump) |
| 9** | AG000750 | O-Ring Segment* |
| 10** | AG055321 | Body O-Ring* |
| 11** | AG055325 | 3 Vane Poly Pump Impeller, New* (a) |
| 11** | AG055324 | 5 Vane Poly Pump Impeller, New* (b) |
| 11** | AG057556 | 4 Vane Poly Pump Impeller, New* (C) |
| 12 | AG055326 | Impeller Bolt, S.S. (a and b) |
| 12 | AG057555 | Impeller Bolt, S.S (C) |
| 13 | AG055332 | Impeller Bolt, Gasket* |
| 14 | AG055335 | Impeller Hex Nut |
| 15 | AG055327 | Poly Pump Volute, New (a and b) |
| 15 | AG057554 | Poly Pump Volute, New (C) |
| 16 | AG000748 | Volute Screw, S.S. (2 per pump) |
| 17** | AG000738 | Poly Pump Check Valve* |
| 18 | AG055329 | Poly Pump Body Assembly, New (a) |
| 18 | AG055328 | Poly Pump Body Assembly, New (b) |
| 18 | AG057553 | Poly Pump Body Assembly, New (C) |
| 19 | AG000974 | Body Screws, S.S. (10 per pump) |
| 20 | AG055336 | Prime/Drain Plug (2 per pump)(a & b) |
| 20 | AG057552 | Drain Plug |
| 21** | AG050532 | O-Ring, Prime/Drain Plug* |
| | |(2 per pump) (a & b) |
| 21** | AG057551 | O-Ring, Prime/Drain Plug # |
| 25 | AG000945 | Upper Volute Screw, S.S. |
| 26 | AG055334 | Rear Bracket Washer, S.S. (4 per pump) |
| 27 | AG055333 | Impeller Key |
| 28** | AG055337 | Poly Pump Slinger, New* |
| 29** | AG006696 | O-Ring for Seal Assembly* |
| ** | AG059983 | Repair Kit, 1-1/2" and 2" with 3.5 HP Engine |
| ** | AG055982 | Repair Kit, 1-1/2" and 2" with 5 HP Engine |
| ** | AG058076 | Repair Kit, 3" |
Pumps
87