Controllers - AGCO Parts

RoGator/TerraGator
New Leader #4 BOC Chain Shields
These chain shields are relative to the New Leader spreaders with the
#4 Belt-Over-Chain conveyor systems and are used to seal the chain
links from the fertilizer product. The part numbers are assembled chain
shields consisting of the metal strip, rubber sealer strip and hardware
attaching the rubber sealer to the metal.
Note that there are part numbers for the RH and LH sides, different
lengths, and also various metal configurations such as carbon steel
(CS), 409 stainless steel (409SS) and 304 stainless steel (304SS). Pick
the proper part according to the size of your spreader and what the
spreader has on it.
The attaching hardware used to fasten the chain shields to the spreader
box is as follows:
AG719051 Carriage Bolt-SS, AG562065 Hex Nut-SS and AG562050
Lockwasher-SS. Use these quantities of each p/n per spreader box; 28
per 12.5' spreader, 30 per 13' spreader and 32 per 14' spreader.
Notes: The chain shields will measure one foot longer than the
spreader box size. If in doubt as to what length is needed, measure
the length of the chain shield for size verification. For example, on a
12' 6" spreader, the chain shields will measure 13' 6" long, on a 13'
spreader, the chain shields will measure 14' long, etc.
| Part | Description |
| AG727320 | Chain Shield, RH-CS 12' 6 |
| AG727326 | Chain Shield, LH-CS 12' 6 |
| AG727321 | Chain Shield, RH-409SS12' 6 |
| AG727327 | Chain Shield, LH-409SS12' 6 |
| AG727322 | Chain Shield, RH-304SS12' 6 |
| AG727328 | Chain Shield, LH-304SS12' 6 |
| AG133070 | Chain Shield, RH-CS13' Spreader |
| AG133071 | Chain Shield, LH-CS 13' Spreader |
| AG133072 | Chain Shield, RH-409SS13' Spreader |
| AG133073 | Chain Shield, LH-409SS13' Spreader |
| AG727561 | Chain Shield, RH-304SS13' Spreader |
| AG727560 | Chain Shield, LH-304SS13' Spreader |
| AG727323 | Chain Shield, RH-CS14' Spreader |
| AG727329 | Chain Shield, LH-CS14' Spreader |
| AG727324 | Chain Shield, RH-409SS14' Spreader |
| AG727330 | Chain Shield, LH-409SS14' Spreader |
| AG727325 | Chain Shield, RH-304SS14' Spreader |
| AG727331 | Chain Shield, LH-304SS 14' Spreader |
Solenoid Shut-off Valve
This valve is used on New Leader
boxes to turn the conveyer off. It has
24 GPM flow rating and is preset at
2500 psi relief.
DICKEY-john System
The DICKEY-john CCS 100 system is a common controller for the New
Leader systems. Listed below are some of the major components for
the L20-20 boxes.
| Part | Description |
| AG711093 | CCS 100 Console |
| AG609014 | CMS 100 Console |
| 72512508 | Dickey - john Radar Sensor without Mounting Bracket |
| AG609004 | CCS 100 Remote Switch |
| AG609003 | Actuator Valve - driver |
| AG609250 | Hydraulic Control Valve 30 GPM with 20 ft Cord |
| AG609001 | Rate Sensor - 10 ft Cable |
Auxillary Hydraulic Outlet
Can be installed on New Leader dry system to
provide a remote hydraulic outlet. Hydraulic
drive augers can then be run by the
TerraGator's hydraulic power.
| Part | Description |
| AG310942 | Auxiliary Hydraulic Outlet |
Spinner Blades
For Henderson and New Leader Boxes.
Note: For a New Leader G4 box, 4 lefts and 4 rights are required.
| Part | Description |
| AG703831 | Henderson and New Leader, Right Hand (3 Req.) |
| AG703832 | Henderson and New Leader, Left Hand (3 Req.) |
| AG562076 | Bolt .31 x 1" SS |
| AG516403 | Nut .31 SS |
New Leader Spread Pattern Test Kit
For G4, GT, and FH New Leader boxes. Kit includes 21 collection trays,
21 dividers, 1 Rack, 21 Test Tubes, 21 Clips, 1 Funnel.
| Part | Description |
| AG132632 | Spread Pattern Test Kit |
| Part | Description |
| AG513800 | Solenoid Valve |
| AG706357 | Coil and Cartridge for 513800 Dump Valve |
| AG610014 | Coil Only - Two wire |
288