AAC SPECIFICATION 418002 ISSUE 3 HYDRAULIC HOSE ...
AAC SPECIFICATION 418002 ISSUE 3 HYDRAULIC HOSE ...
AAC SPECIFICATION 418002 ISSUE 3 HYDRAULIC HOSE ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>AAC</strong> <strong>SPECIFICATION</strong> <strong>418002</strong><br />
<strong>HYDRAULIC</strong> <strong>HOSE</strong> & FITTINGS FOR USE IN<br />
COAL MINING APPLICATIONS<br />
<strong>ISSUE</strong> 3<br />
COPYRIGHT<br />
-12 19 ¾ 38,0 300 400K @ 133% WP<br />
-16 25 1 32,0 340 400K @ 133% WP<br />
-16 25 1 38,0 340 400K @ 133% WP<br />
-20 31 1 ¼ 35,0 460 400K @ 133% WP<br />
-24 38 1 ½ 30,0 560 400K @ 133% WP<br />
-32 51 2 25,0 700 400K @ 133% WP<br />
<strong>HYDRAULIC</strong> EXTRA HIGH PRESSURE LINES 6 SPIRAL<br />
-20 31 1 ¼ 38,0 420 500K @ 120% WP<br />
-24 38 1 ½ 38,0 510 500K @ 120% WP<br />
-32 51 2 35,0 640 500K @ 120% WP<br />
ENGINE AND TRANSMISSION LINES<br />
-4 6 ¼ 40,0 100 200K @ 133% WP<br />
-6 10 ⅜ 33,0 130 200K @ 133% WP<br />
-8 12 ½ 27,5 180 200K @ 133% WP<br />
-12 19 ¾ 21,5 240 200K @ 133% WP<br />
-16 25 1 16,5 300 200K @ 133% WP<br />
-20 31 1 ¼ 12,5 420 200K @ 133% WP<br />
-24 38 1 ½ 9 500 200K @ 133% WP<br />
Note: The minimum bend radius is measured to the external surface of the hose on the<br />
inside of the bend.<br />
4.8 FEMALE SWIVEL <strong>HOSE</strong> END FITTINGS<br />
The Contractor shall submit his design for female swivel hose end fittings for approval. All<br />
JIC female hose ends to have a double hex design to alleviate hose twist at installation.<br />
All metric hose ends to be of the DKO design. All hose end nipples, straight & elbows, for<br />
use on ultra high pressure hose shall be manufactured from solid material. (No brazed<br />
joints) All hose end nipples for use on spiral hose from DN25 upwards to incorporate the<br />
wire trap design.<br />
4.8.1 Material: Shall be free cutting leaded steel that complies with the requirements of DIN<br />
1651.<br />
4.8.2 Surface texture and tolerances: Shall comply with the requirements of SAE J516.<br />
<strong>AAC</strong>_SPEC_<strong>418002</strong>03 APPROVED 8 May 1991 Page 7 of 10<br />
Anglo Technical Division accepts no liability for any damage whatsoever that may result from the use of this material or<br />
the information contained therein, irrespective of the cause and quantum thereof.