LTR20071000, Rev. B 5/30/07 - Cal Spas

More documents

Recommendations

Info

Preparing for Your New Portable Spa 240 Volt Electrical Installation All 240V spas must be permanently connected (hard wired) to the power supply. These instructions describe the only acceptable electrical wiring procedure. Spas wired in any other way will void your warranty and may result in serious injury. These are the only acceptable electrical wiring procedures. Spas wired in any other way will void your warranty. See the wiring diagrams on the following pages When installed in the United States, the electrical wiring of this spa must meet the requirements of National Electric Code, ANSI/NFPA 70-2005 and any applicable local, state, and federal codes. The electrical circuit must be installed by an electrical contractor and approved by a local building / electrical inspector. GFCI and Wiring Requirements The power supplied to the spa must be on a dedicated GFCI protected circuit as required by NEC 680.31 with no other appliances or lights sharing the power. All 240V spas require one 50 amp GFCI with four #8 AWG copper wires. Ultimate Fitness spas with the optional 5.5kW auxiliary heater require a second dedicated electrical service with one 30 amp GFCI and three #8 AWG copper wires. Use copper wire with THHN insulation. Do not use aluminum wire. When NEC requires the use of wires larger than #6 AWG, install a junction box near the spa and use #6 AWG wire between the junction box and the spa. Wire runs over 85 feet must increase wire gauge to the next lower number. For example: A normal 50 amp GFCI with four # 6 AWG Copper wires run over 85 feet would require you to go to four # 4 AWG copper wires. Testing the GFCI Breaker Test the GFCI breaker prior to first use and periodically when the spa is powered. To test the GFCI breaker follow these instructions (spa should be operating): 1. 2. Press the TEST button on the GFCI. The GFCI will trip and the spa will shut off. Reset the GFCI breaker by switching the breaker to the full OFF position, wait a moment, then turn the breaker back on. The spa should have power again. Page 6 2007 Portable Spa Owner’s Manual LTR20071000, Rev. B
GFCI Hook-Up Preparing for Your New Portable Spa 2007 Portable Spa Owner’s Manual Page 7 LTR20071000, Rev. B
Page 1 and 2: LTR20071000, Rev. B 5/30/07
Page 3 and 4: Read This First! Important Safety I
Page 5 and 6: Basic Spa Information The following
Page 7: Electrical Set-up Before Delivery o
Page 11 and 12: Operating Your Spa 5900, 6000, and
Page 13 and 14: Operating Your Spa dr Insufficient
Page 15 and 16: Operating Your Spa 6300 Controls -
Page 17 and 18: 7000, 9000, and 9800 Electronic Con
Page 19 and 20: Operating Your Spa Freeze Protectio
Page 21 and 22: Auxiliary Control Operation Operati
Page 23 and 24: Pulse Mode This button allows the u
Page 25 and 26: Operating Your Spa 4. Locate hose e
Page 27 and 28: Filtration Cycles The filtration cy
Page 29 and 30: Water Quality Maintenance Ph / Alka
Page 31 and 32: Chlorine Clear Water Plan This plan
Page 33 and 34: Water Quality Maintenance 13. Use S
Page 35 and 36: Maintenance Regardless of which “
Page 37 and 38: Cleaning and Maintenance maintenanc
Page 39 and 40: Using the Cal Entertainment System
Page 41 and 42: Programming the Universal Remote Co
Page 43 and 44: PLU21703427 (MNW) 2.5”, NECK JET,
Page 45 and 46: Valves PLU21300052 DIVERTER VALVE 1
Page 47 and 48: Appendix Filters FIL11100190 FIL111
Page 49 and 50: Appendix Basic Grey 4” x 2” Par
Page 51 and 52: Deluxe Grey 5 to 3 Part No. Descrip
Page 53 and 54: Keeping Fit with your Cal Spa The f
Page 55 and 56: Cal Spas Chemicals Appendix 2007 Po
Page 57 and 58: 2007 Portable Spa Owner’s Manual
Page 60:
Locating the product serial number
show all

LTR20071000, Rev. B 5/30/07 - Cal Spas

Create successful ePaper yourself

Delete template?

Save as template?