T8 Troffer Reflector Kit - Howard Lighting

Specification Sheet
FTR2 Series
Linear Fluorescent
3/22/2013
T8 Troffer Reflector Kit
Delamps up to 4-lamp grid ceiling fixtures to 2-lamps
The FTR2 Troffer Reflector Kit is a simple, cost-effective onepiece
reflector used to change fixtures from 2, 3, or 4-lamp to
a 2-lamp. This kit uses a reflector, brackets and Tek screws to
provide you with recentered lamps without replacing the entire
fixture. Additionally, the FTR2 kit offers reduced energy, better
lighting efficiency and minimal light loss. Four reflector options
include enhanced specular aluminum, specular aluminum, white
reflector and white optics.
Reflector
Project:
Catalog#:
Approved by:
Bracket
Dimensions
Front View
2-1/2”
Tek Screw
.014” reflector material thickness
9-3/4”
20-1/2”
Plan View
Model
Family
Dimensions
Number
of Lamps
ORDERING INFORMATION
Reflector Material
Packaging Code
FTR2 4 2 E KR
FTR2 2 - 2’ x 2’
4 - 2’ x 4’
2 N - No Reflector (use with BRKT option)
A - Specular Aluminum (86%)
E - Enhanced Specular Aluminum (95%)
W - White Reflector (91%)
O - White Optics (98%)
KR - Kit with Rapid Start Lampholders
KI - Kit with Instant Start Lampholders
REFL - Reflector only
BRKT - Bracket only (use N reflector option)
Sample Ordering Number:
FTR2 4 2 E KR
Fluorescent T8 Troffer Reflector Kit
2ft by 4ft dimensions
2 lamps
Enhanced Specular Aluminum Reflector
Kit with Rapid Start Lampholders
KR Kit Includes:
2 - Brackets
8 - Tek Screws
4 - Rapid Start Lampholders
1 - Reflector
KI Kit Includes:
2 - Brackets
8 - Tek Screws
4 - Instant Start Lampholders
1 - Reflector
Specifications subject to change without notice.
Howard Lighting Products | 580 Eastview Drive | Laurel, MS 39443
(toll free) 800.956.3456 | (direct) 601.422.0033 | (fax) 601.422.1652
www.HowardLightingProducts.com

Specification Sheet
FTR2 Series
Linear Fluorescent
3/22/2013
T8 Troffer Reflector Kit
Delamps up to 4-lamp grid ceiling fixtures to 2-lamps
Installation Information
Project:
Catalog#:
Approved by:
Socket Plate
with Lampholders
Reflector
NOTE:
2’x2’ Reflector
Assembly
Not Shown
NOTE: Do not remove clear protective film from reflector until Step #8.
1. Turn off and lock out electrical power to the lighting fixture during the installation process.
2. Open or remove fixture doorframe (with lens or louver) from lighting fixture to gain access to the
interior of the fixture.
3. Remove lamps, ballast covers and lampholder brackets.
4. Disconnect ballast (may not be required) to be removed and remove completely with related wire
and lampholders from fixture. Ensure remaining ballast is adequately connected to circuit and
unused wires are capped off and secured with UL Listed insulating connectors (wirenuts, electrical
tape, etc).
5. Reinstall remaining lampholders into new socket brackets, route wires preventing any pinching or
damage to wires leading to the ballast.
6. Center socket brackets on each end of fixture and fasten using TEK screws provided.
7. Remove protective film from reflector and secure reflector in place.
8. Replace lamps.
9. Re-install fixture door with lens or louver.
10. Reapply power to fixture
Specifications subject to change without notice.
Howard Lighting Products | 580 Eastview Drive | Laurel, MS 39443
(toll free) 800.956.3456 | (direct) 601.422.0033 | (fax) 601.422.1652
www.HowardLightingProducts.com