AQUASMART-ADY-2K - Antrifttaler Kunststoff-Vertriebs GmbH
AQUASMART-ADY-2K - Antrifttaler Kunststoff-Vertriebs GmbH
AQUASMART-ADY-2K - Antrifttaler Kunststoff-Vertriebs GmbH
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>AQUASMART</strong>-<strong>ADY</strong>-<strong>2K</strong><br />
Unique Water based two component, Aliphatic, Satin Finish Polyurethane for Top-Coat,<br />
Concrete Sealing and wood protection applications.<br />
Description:<br />
<strong>AQUASMART</strong> –<strong>ADY</strong> <strong>2K</strong> is a two component,<br />
water based, aliphatic coating with exceptional<br />
performance in a multitude of applications.<br />
Main areas of application are as a top-coat for<br />
polyurethane and Epoxy based solvent free, self<br />
leveling floor systems; As a penetrative concrete<br />
sealer and as an impregnation coating for<br />
natural stone.<br />
The product has excellent UV, chemical, water<br />
and abrasion resistance. It is easily pigmented<br />
with off the shelf water based pigment pastes in<br />
a 5-10% by weight ratio depending on the hiding<br />
power required.<br />
Application is carried out with a roller with at a<br />
consumption of 250-300 gr/m2.<br />
Recommended for:<br />
• As a top coat over Hyperfloor and other<br />
polyurethane self leveling floors as well<br />
as epoxy based floor coatings.<br />
• As a concrete sealer<br />
• Protection of natural stone<br />
• Industrial paint<br />
Features & Benefits:<br />
• Water based<br />
• Easy to apply .<br />
• Excellent abrasion resistance<br />
• Excellent UV resistance.<br />
• Easy pigmentation with water based<br />
pigment concentrates<br />
• Relatively long pot life<br />
• Excellent interlayer adhesion<br />
Application Prerequisites:<br />
Can be successfully applied on:<br />
Concrete, fibrous cement, cement roof tiles, wood,<br />
corroded metal, galvanized steel. For information<br />
about other substrates, please contact our tech<br />
department.<br />
Standard concrete substrate conditions (no primer<br />
needed):<br />
• Hardness: R28 = 15 Mpa.<br />
• Temperature: 5-35 oC.<br />
• Relative humidity: < 85%.<br />
Suitable primers: Aquadur, primer-W, primer-T<br />
Universal Primer, Microsealer depending on the<br />
substrate. Please contact our technical department<br />
for primer selection advice.<br />
Application Procedure:<br />
Clean the substrate using a high pressure washer, if<br />
possible. Remove oil, grease and wax contaminants.<br />
Mixing:<br />
Use a low speed (300 rpm) mixer . Add second<br />
component and continue mixing for a few minutes.<br />
Application:<br />
Apply with roller, at a minimum of 250 gr/m2 in two<br />
coats.<br />
Make sure not to disturb applied material with<br />
excessive rolling as roll marks may appear.<br />
The material is relatively fast drying and therefore<br />
any additional rolling after first application will cause<br />
surface defects to appear.<br />
Make sure first coat is completely dry before second<br />
coat is applied.<br />
Consumption: Minimum consumption<br />
250 gr/m2 in two coats<br />
Shelf Life:<br />
Can be kept for 12 months minimum in the original<br />
unopened pails in dry places and at temperatures of<br />
5-25 oC.
Cleaning:<br />
Clean tools and equipment with water.<br />
Packaging:<br />
4, 10 litres<br />
Safety Information:<br />
The MSDS (Material Safety Data Sheet) is available on<br />
request.<br />
Technical specifications:<br />
In liquid form (before application):<br />
Property Units Method Specification<br />
Viscosity (Brookfield) cP ASTM D2196-86, @ 25°C 100-200<br />
Specific weight gr/cm³ ASTM D1475 / DIN 53217 /<br />
1<br />
ISO 2811, @20°C<br />
Required application<br />
°C - > 5<br />
temperature<br />
Solids content (in water) % - 40<br />
In cured form (after application)::<br />
Property Units Method Specification<br />
Hardness Shore D ASTM D2240 / DIN 53505 /<br />
60<br />
ISO R868<br />
H2O absorption % -