CrX4 User Manual - LinPlug Virtual Instruments

More documents

Recommendations

Info

Crusher The CrX4’s Crusher is a distortion effect that combines bit-depth and sample-rate reduction with “smoothing” algorithms allowing the resolution of the signal to be decreased, thereby making the sound rougher and noisier. This effect processor also includes a filter. The Bits (BitCrusher) control enables you to reduce the bit depth of the output signal from oo bits (the signal is not changed) to 1.00 bits. Reducing the bit depth adds a harsh, noisy quality to the sound. The Cutoff slider is used to set the frequency (in Hz) above which frequencies are filtered out of the signal. Higher settings produce brighter sounds while lower settings result in darker sounds. Range 40 Hz...20 kHz. The Filter Type popup menu right of the Cutoff slider allows you to select one of four filter types: LP12 (Low Pass 12 dB), HP12 (High Pass 12 dB), BP12 (Band Pass 12 dB) and BR12 (Band Reject 12 dB). The Resonance slider is used to set the amount of emphasis around the cutoff frequency. Higher settings create a more pronounced peak in the signal while lower settings produce a flatter response. Range: 0%...100%. The Divider slider controls a sample-rate divider that divides the current sample-rate by the current slider setting. For example, if the current sample-rate is 44.1 kHz, then setting the Divider slider to 2, halves the sample-rate to 22.05 kHz. Ranges from 1 to 32. When the Divider slider (described above) is set to a value other than 1, a new output sample value must be created for each group of samples in the input audio stream. For example, if the Divider slider is set to a value of 4, then four (possibly different) samples in the input stream are replaced by four samples with a single value in the output audio stream. CrX4 User Manual 42
The Divider Mode popup menu determines how the output sample value is created from the input samples. Three options are available: – AVG” (Average) option calculates the average of the input samples and uses this as the output sample value for each of the input samples. – STP (Step) option takes the first sample in each group of input samples and uses this as the output sample value for each of the input samples. – SLD (Slide) option takes the first sample in each group of input samples, interpolates between them and uses the interpolated value as the output sample value for each of the input samples. The Fil Post Div (Filter Post Divider) button is used to set the position of the Crusher’s Filter with respect to the Divider. By default, the Filter is before the Divider in the signal path. Switching this button on moves the Filter to after the Divider in the signal path. The Smoother button allows a compressor / expander to be switched into the signal path. This reduces the overall effect of the Crusher making the sound less harsh and more “musical”. CrX4 User Manual 43
Page 1 and 2: CrX4 User Manual Copyright LinPlug
Page 3 and 4: Welcome Thank you for purchasing a
Page 5 and 6: Ping Pong (Delay)..................
Page 7 and 8: Common to Mac and PC The first time
Page 9 and 10: output of filter 1 is send to filte
Page 11 and 12: User Interface Sections The user in
Page 13 and 14: The Generator Controls The upper an
Page 15 and 16: Time Sampler Generator The Time Sam
Page 17 and 18: Wavetable Generator The CrX4's Wave
Page 19 and 20: which is looped. These three parame
Page 21 and 22: dynamically to MIDI input. If you o
Page 23 and 24: Oscillator Generator The Oscillator
Page 25 and 26: Filters The CrX4 contains two indep
Page 27 and 28: The Filter Envelope section is loca
Page 29 and 30: Velocity to Main Volume The Velo (V
Page 31 and 32: Effects The CrX4 has 6 independent,
Page 33 and 34: St (Stereo) Delay The Stereo delay
Page 35 and 36: Chorus The Chorus effect can be use
Page 37 and 38: Filter The Drive slider (Saturation
Page 39 and 40: Flanger The CrX4’s Flanger can be
Page 41: Stereo Enhancer The CrX4’s Stereo
Page 45 and 46: The Envelopes are positioned in eac
Page 47 and 48: LFO The CrX4’s LFO (“Low Freque
Page 49 and 50: Modulation Matrix The CrX4's Modula
Page 51 and 52: § Random: In this mode the notes o
Page 53 and 54: Preset Browser The Preset Browser s
Page 55 and 56: To use the CrX4’s ECS feature, pr
Page 57 and 58: Library Location / Startup Patch Wh
Page 59 and 60: The “Allow Host Program Change”
Page 61 and 62: LFO: An LFO or Low Frequency Oscill
Page 63 and 64: Appendix A: Tempo Sync Settings Tem
Page 65 and 66: Expression Contr. LFO 1 LFO 2 LFO 3
Page 67 and 68: Note: The Filters 1 and 2 offer the
Page 69 and 70: Appendix D: Using TUN files in the

CrX4 User Manual - LinPlug Virtual Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?