CronoX 2 User Guide 1.02.sdw - LinPlug Virtual Instruments

More documents

Recommendations

Info

Effects The CronoX has a stereo effects unit located on the bottom right of the front panel. The effects unit contains seven modules: Drive, Delay, Chorus, Phaser, Filter, Reverb and StDelay ("Stereo Delay"). To change the effect type click on the menu to the left of the Effect label. The Drive effect is always present and precedes the other six effects. Each effect's controls differ slightly. Each effect is described in detail below. Drive The Drive dial sets the amount of distortion that is applied to the signal before it is fed into the following section of the effects unit. The further the dial is turned clockwise, the more the signal is distorted. Distortion sounds best if applied to complex signals. Note that the drive effect can be applied independently of the other section of the effects unit. Range: 0%...100%. LinPlug CronoX User Guide 1.02 30
Delay The Delay effect can be used to create "echoes" and other related effects. It features controls for "Wet", "Time", "Feedback", "Filter", "Rate", "Depth" and "Sync". The Wet dial allows you to set the balance between the processed "wet" signal and the original unprocessed "dry" signal. Range: 0%...100%. The Time slider is used for setting the delay time (in milliseconds). Range: 1 ms...680 ms. The Feed (Feedback) slider allows you to set the number of times the signal repeats or "echoes". Range: 0%...99%. Also included in the Delay section is a variable low pass/high pass 6dB/Oct filter. Range: -1.00...1.00. The Rate dial sets the rate (in Hz) at which the modulation takes place. As an example, when you set the Delay Rate to 0.5Hz you get a complete sweep from 50ms (using the above example) to 150ms and back to 50ms in 2 seconds. Range: 0.01 Hz...2.00 Hz. The Depth dial is used to set the depth to which the delayed signal is modulated. For example, if you set a delay time of 100ms and a depth of 50%, the amount of modulation is 50% of 100ms (50 ms). In this case you'll get a delay time that varies from 100 - 50ms (50ms) up to 100 + 50ms (150ms). Range: 0.00...0.99. Finally, you can use the Sync menu to sync the delay time with the song's current tempo (see Appendix C for the range of possible sync settings). Normally it doesn't make much sense to combine a synced delay time with delay time modulation. LinPlug CronoX User Guide 1.02 31
Page 1 and 2: Copyright: LinPlug Virtual Instrume
Page 3 and 4: Welcome Thank you for buying the "C
Page 5 and 6: GET THE FULL VERSION...............
Page 7 and 8: Mac Installation The CronoX comes w
Page 9 and 10: Overview The CronoX is a 24 note-po
Page 11 and 12: Generators The CronoX's Generator s
Page 13 and 14: TimeSamp Generator The TimeSamp Gen
Page 15 and 16: Schrader Generator The CronoX's "Sc
Page 17 and 18: Source The Source section of the Cr
Page 19 and 20: Filter The CronoX's filter has been
Page 21 and 22: Amplifier The CronoX's Amplifier se
Page 23 and 24: Modulation One of the key features
Page 25 and 26: The Fade slider is used to set the
Page 27 and 28: The Attack dial setting determines
Page 29: The three buttons at the top of the
Page 33 and 34: Phaser The CronoX Phaser can be use
Page 35 and 36: Reverb The Reverb effect is used to
Page 37 and 38: Preset The CronoX's Preset section
Page 39 and 40: In this case it will take the same
Page 41 and 42: Keyboard The CronoX's Keyboard enab
Page 43 and 44: Master Tune is used to set the over
Page 45 and 46: Optimizing CPU Usage Software synth
Page 47 and 48: LFO: Microtuning: Modulation Matrix
Page 49 and 50: Appendix A: Using TUN Files By Jack
Page 51 and 52: 5. Type "set synth" in the command-
Page 53 and 54: Appendix B: Modulation Sources and
Page 55 and 56: Time Samp 2 Cutoff Resonance Pulsew
Page 57: Appendix C: Delay Sync Settings Off

CronoX 2 User Guide 1.02.sdw - LinPlug Virtual Instruments

Create successful ePaper yourself

Delete template?

Save as template?