Belimo VRD2 - TROX
Belimo VRD2 - TROX Belimo VRD2 - TROX
Maintenance 1 Contents Subject Page Maintenance 2 Blade Position Indicator 2 Replacement of Control Components 2 Design changes reserved · All rights reserved · ® Gebrüder Trox GmbH (12/2001) · Leaflet No. E016NA6
Removing tubes Maintenance 1 Special tool for removing tubing Blade Position Indicator 5 4 3 2 1 VAV terminal unit 2 Actuator 3 Shaft with position indicator Measuring Equipment Required: 4 Rotation angle limiter 5 Control damper blade Electronic control Pneumatic control • Digital voltmeter • Pressure gauge, 0 to 1.5 bar • Manometer, 0 to 1000 Pa • Manometer, 0 to 1000 Pa • Service unit DDC control • Service computer • Digital voltmeter • Manometer, 0 to 1000 Pa 1 1 2 Maintenance Safety Note • Maintenance should only be carried out by specialists! The control damper mechanism on the VAV terminal unit is maintenance-free. To ensure perfect functioning of the entire system, function tests should be carried out as part of the regular system maintenance. The following criteria should be used: 1. Does the room temperature controller function? 2. Does the volume flow controller function? 3. Does the actuator turn in both directions? 4. Does the transducer output signal vary according to the actuator movements? 5. Do the override controls such as shut off function? 6. Are the tubing connections airtight? Further details on fault diagnosis are given in the information on each controller type. Replacement of Control Components If faulty control components have to be replaced, the following principles must be observed: • Spare parts must comply with the technical requirements of the manufacturer. Only use original spare parts. • Disconnect supply voltage 24 volts or operating pressure. • Mark wiring/tubing connections before releasing. • Carefully remove pneumatic tubing without pulling. • Replace component and all connections. When replacing controllers and transducers, they must be adjusted to suit the unit size. Therefore electronic and pneumatic components are preset in the Trox works. Digital controllers can be set up by the customer. When changing actuators, note the following: • Mechanical rotation angle limiters on the new actuator should be set as the existing unit. A slot in the control damper shaft shows the position of the blade. • Direction of rotation should be set as before (switch or plug setting).
- Page 1 and 2: VARYCONTROL Reference List Design a
- Page 3 and 4: Reference list VARYCONTROL KADEWE-B
- Page 5 and 6: TVZ · TVA TVM TVR TVRK TVJ/TVT Des
- Page 7 and 8: Room Temperature Control Circuit Se
- Page 9 and 10: Single Duct System with Reheat Coil
- Page 11 and 12: Explanation of Order Codes The cont
- Page 13 and 14: Installation 1 Contents Subject Pag
- Page 15 and 16: Installation TVZ . TVA Delivery and
- Page 17 and 18: Installation TVJ with TX TVJ/TVT wi
- Page 19 and 20: Disengaging the Drive Function Test
- Page 21: TVRK Volume Flow Controller and Tra
- Page 25 and 26: VRD2 VRD2 Tube connection for trans
- Page 27 and 28: Pressure Independent Control Charac
- Page 29 and 30: Volume Flow Ranges TVZ, TVA, TVR, T
- Page 31 and 32: Volume Flow Ranges TVM Size V · mi
- Page 33 and 34: Override Controls RT Controller Ope
- Page 35 and 36: Function Test Fault Finding Check C
- Page 37 and 38: VRP � � � � Characteristic
- Page 39 and 40: VRP Adjustment Knobs � � �
- Page 41 and 42: Volume Flow Control Tolerances 1) V
- Page 43 and 44: Terminal Connections Plug connectio
- Page 45 and 46: Function Test Fault Finding Check C
- Page 47 and 48: VRP-STP Area of Application ��
- Page 49 and 50: Room Pressure Ranges Differential p
- Page 51 and 52: Parallel Differential Pressure Cont
- Page 53 and 54: Belimo VFP 1 Contents Subject Page
- Page 55 and 56: Belimo VFP Zero Point Adjustment
- Page 57 and 58: NM 24-V � Shaft clamp � Directi
- Page 59 and 60: Belimo VAV-Compact NMV-D2 1 Content
- Page 61 and 62: Belimo VAV-Compact NMV-D2 Character
- Page 63 and 64: Belimo VAV-Compact NMV-D2 Volume Fl
- Page 65 and 66: Belimo VAV-Compact NMV-D2 Volume Fl
- Page 67 and 68: Belimo VAV-Compact NMV-D2 Variable
- Page 69 and 70: Belimo VAV-Compact NMV-D2 Slave Con
- Page 71 and 72: Belimo VAV-Compact NMV-D2M 1 Conten
Maintenance<br />
1<br />
Contents<br />
Subject Page<br />
Maintenance 2<br />
Blade Position Indicator 2<br />
Replacement of Control Components 2<br />
Design changes reserved · All rights reserved · ® Gebrüder Trox GmbH (12/2001) · Leaflet No. E016NA6