marcy mwm 981 home gym - Impex Fitness

More documents

Recommendations

Info

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert the two Guide Rods (#11) through Rubber Bumpers and into the holes on the Rear Stabilizer. Secure each Guide Rod with one M10 x 1” Allen Bolt (#64) and � ¾” Washer (#73) from the bottom. The Guide Rods has holes on the rod to lock the weight stack when not in use. The shorter end of the guide rod with the lock hole will need to be pointed downwards towards the Rear Stabilizer. B.) Do not tighten all Nuts and Bolts starting from this procedure until instructed to do so. C.) Attach two Rubber Bumpers (#28) onto the holes onto the Guide Rods. D.) Attach the Base Frame (#3) to the Rear Stabilizer. Secure them with two M10 x 4” Carriage Bolts (#59), one U-shaped Bracket (#20), two Ø ¾” Washers (#73), and two M10 Aircraft Nuts (#70). E.) Attach the Vertical Frame (#4) onto the Base Frame. Secure them with two M10 x 2 3/8” Carriage Bolts (#58), one 1 ¾” x 4 ¾” Bracket (#18), two Ø ¾” Washers (#73), and two M10 Aircraft Nuts (#70). F.) Slide 11 Weight Plates (#50) onto the Guide Rods. Make sure the deep grooves on the Weight Plates all face the back of the machine and downward. Align the holes on the Weight Plates. Insert a Selector Rod (#21) through the center hole. Slide the Selector Stem (#51) onto the Guide Rods. G.) Use a Weight Selector Pin (#44) to select the number of Weight Plates to exercise. Attach the ring on Weight Selector Pin’s cable onto the Selector Rod. Note: Each Weight Plate weights approximately 10 lbs. Please refer to the Weight Resistance Chart in page 25. H.) Attach the Seat Support (#5) to the Vertical Frame. Secure it with two M10 x 2 3/8” Carriage Bolts (#58), one 1 ¾” x 4 ¾” Bracket (#18), two Ø ¾” Washers (#73), and two M10 Aircraft Nuts (#70). I.) Attach the Vertical Seat Support (#6) to Seat Support and Base Frame. Secure each end of Vertical Seat Support with two M10 x 1” Allen Bolts (#64) and two Ø ¾” Washers (#73). 6
Page 1 and 2: NOTE: Please read all instructions
Page 3 and 4: IMPORTANT SAFETY NOTICE PRECAUTIONS
Page 5: HARDWARE PACK NOTE: The following p
Page 9 and 10: STEP 2 (See Diagram 2) A.) Attach t
Page 11 and 12: STEP 3 (See Diagram 3) A.) Attach t
Page 13 and 14: STEP 4 (See Diagram 4) A.) Insert t
Page 15 and 16: STEP 6 (See Diagram 6 & Cable Loop
Page 17 and 18: STEP 7 (See Diagram 7& Cable Loop D
Page 19 and 20: 18 DIAGRAM 8
Page 21 and 22: Set up the Lock Combination A.) The
Page 23 and 24: MWM981 WEIGHT RESISTANCE CHART Weig

marcy mwm 981 home gym - Impex Fitness

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?