DPX-620 OPERATION MANUAL

1 2 3 4 5 6 7 8 9 10
R
DPX-620 OPERATION MANUAL
GENERAL
This model is a6channel dimmer pack, has avariety of functions, including DMX,
ANALOG and MANUAL control modes ,Dimming, Preheat control, overheat and overload
protection, and DMX 512 address allowing to simultaneously control 6channel output.
TECHNICAL SPECIFICATIONS
1. Power input: 3-phase or single phase input
AC 230V~50-60Hz( CE )
AC 220V~50-60Hz( CHINA )
2. Power output: 10A per channel max. Total 60A max.( CE )
20A per channel max., Total 120A max.( CHINA )
3. Fuse :20A circuit breaker
4. Dimensions: 482x370x85mm
5. Weight:7.1Kg
PRECAUTIONS BEFORE INSTALLING
1.Fitting construction of this unit is as follows:
Wiring cover
Wiring enclosure
CONTROLS AND FUNCTIONS
FRONT PANEL
2
CH1
CH3
CH5
1. Channel indicator (x6)
These indicators are turned on without connecting load, they are turned off when load is connected.
2. Circuit breaker (x6)
This circuit breaker will cut off power supply automatically when load current exceeds 20A
3. Dip switch
These switches are set to select initial channel setting mode.
4. PREHEAT control
This control adjust the initial lighting point.
5. DMX indicator
6. Channel dimmer indicator (x6)
7. Channel dimmer control (x6)
These controls adjust appropriate channel dimmer level.
8. Power switch
9. Power indicator
REAR PANEL
1
CH2
CH4
CH6
4 5 6
ON
OFF
DMXSIGNAL
25%
0 50%
PREHEAT
STARTADDRESS
3
10
8
6
4
2
0
CH1 CH2 CH3 CH4 CH5 CH6
10
8
6
4
2
0
IN PARALLEL
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
10
8
6
4
2
0
9
POWER
7 8
Enclosure
2.Remove wiring cover, connect wires in accordance with this manual or screen print
on the top cover.
1 2 3 4
5
24-004-0028

1. DMX output socket
Use to connect to DMX input socket of next unit for parallel control.
2. DMX input socket
Use to connect to DMX input signals.
3. ANALOG output (8-pin din socket)
4. ANALOG input (8-pin din socket)
5. Output wiring port (x5)
Use to connect to 6channel output, 10A per channel max., Total 60A max.( CE )
20A per channel max., Total 120A max. ( CHINA )
OPERATION
1. Please confirm power requirement is matched with that specified on this unit
2.Set up correct wire connections. (see connections diagram).
3. Apply to required control signals.
4. Check for proper wire connections, turn power switch on.
5. Allow the system to connect available control signals at atime, the prevailing one should
control channel output. If PREHEAT control is set to maximum, channel dimmer level should
be 50 percent of setting maximum dimmer.
6. Receive DMX signals
. Primarily, select initial channel to apply to DMX signals.
. Set dipswitch 10 to ON, the system should receive only the first channel DMX signals
which synchronously control 6channel output.
. Set dipswitch 10 to OFF,the system should receive 6channel D MX signals and control 6
channel output in sequence, how DMX indicator should turn on.
7. Appropriate initial channel DMX setting mode is refered to following table:
SINGLE PHASE CONNECTION
LOADING E
CH6 CH5 CH4 CH3 CH2 CH1
N
N
N
N
1 2 3 4 5 6 7 8 9 Initial channel
0 0 0 0 0 0 0 0 0 0
1 0 0 0 0 0 0 0 0 1
0 1 0 0 0 0 0 0 0 2
1 1 0 0 0 0 0 0 0 3
0 0 1 0 0 0 0 0 0 4
LOADING
N
L
CHINA
POWER INPUT:
OUTPUT:
POWER INPUT:
OUTPUT:
AC 230V~50-60Hz
10A per channel, Total 60A
AC 220V~50-60Hz
20A per channel,Total120A
1 1 1 1 1 1 1 1 0 255
0 0 0 0 0 0 0 0 1 256
1 0 0 0 0 0 0 0 1 257
THREE-PHASE CONNECTION
1 1 1 1 1 1 1 1 1 511
LOADING E N N N N
CH6 CH5 CH4 CH3 CH2 CH1
L3
L2
L1
8. Turn the power switch off, adjust channel program setting, and then turn the power on.
9. Receive 0-10V power level signals.
This unit transmit received level signals to ANALOG output, output supply is +20V DC
600mA max.
CHINA
LOADING
POWER INPUT:
OUTPUT:
POWER INPUT:
OUTPUT:
N L3 L2 L1
AC 230V~50-60Hz
10A perchannel, Total 20A per phase
AC 220V~50-60Hz
20A perchannel, Total 40A per phase
WARNING:
1. This apparatus must be earthed
2. Toprevent fire or electric shock hazard, do not expose this apparatus to rain
or moisture.
3. In case circuit breaker is cut off automatically, check corresponding channel
to find whether there is any malfunction.
4.To assure ventilation, do not block or stack goods near to openings.
5. Wait for at least 3seconds to turn on your unit after you have turned off your unit.