Endopore Implants with external hex - Optident
Endopore Implants with external hex - Optident
Endopore Implants with external hex - Optident
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Osteotome PROCEDURES<br />
peRfect<br />
NTERNAL<br />
PERFECT SURFACE<br />
ENDOPORE ®<br />
Product Catalog<br />
INTERNAL HEX<br />
PerfeCT SURFACE<br />
EXTERNAL HEX<br />
Implant Placement Procedure
ENDOPORE ®
Table of Contents<br />
ENDOPORE ®<br />
Contents<br />
<strong>Endopore</strong> <strong>Implants</strong><br />
<strong>with</strong> internal connection<br />
4 <strong>Endopore</strong> <strong>Implants</strong> <strong>with</strong> internal<br />
connection for one-stage surgery<br />
5 Case Planning Chart<br />
Crown and Bridge Restorations<br />
7 Cover Screws<br />
7 Cementable Abutments<br />
7 ECO Abutment System<br />
8 Octabutment System<br />
Overdenture Restorations<br />
9 Locator System<br />
10 Dalla Bona Abutment System<br />
10 O-Ring Abutment System<br />
<strong>Endopore</strong> <strong>Implants</strong><br />
<strong>with</strong> internal Hex<br />
11 <strong>Endopore</strong> <strong>Implants</strong> for one-stage<br />
and two-stage surgery<br />
12 Case Planning Chart<br />
Crown and Bridge Restorations<br />
14 Cover Screws<br />
14 Healing Abutments<br />
15 Transfer Copings<br />
15 Implant Analogs<br />
15 Retaining Screws<br />
16 Hexed Abutments<br />
16 Angled Abutments<br />
17 UCLA Abutments<br />
Overdenture Restorations<br />
18 Locator System<br />
19 O-Ring Abutment System<br />
19 Dalla Bona Abutment System<br />
20 UMA System<br />
<strong>Endopore</strong> <strong>Implants</strong><br />
<strong>with</strong> <strong>external</strong> Hex<br />
21 <strong>Endopore</strong> External Hex Connection<br />
implants for one-stage and two-stage<br />
surgery<br />
23 Case Planning Chart<br />
Crown and Bridge Restorations<br />
26 Cover Screws<br />
26 Healing Abutments<br />
27 Transfer Copings<br />
28 Implant Analogs<br />
28 Retaining Screws<br />
29 Hexed Abutments<br />
30 Angled Abutments<br />
30 Temporary Titanium Abutments<br />
31 UCLA Abutments<br />
Overdenture Restorations<br />
32 Locator System<br />
32 O-Ring Abutment System<br />
33 Dalla Bona Abutment System<br />
34 UMA System<br />
36 Prosthetic Instrumentation<br />
Surgery<br />
38 <strong>Endopore</strong> Surgical Kits<br />
39 <strong>Endopore</strong> Surgical Instrumentation<br />
42 Articles in alphabetical order<br />
<br />
Internet<br />
All print material released by Sybron Implant Solutions is available online, too. Product catalogs<br />
and insertion brochures as well as information for patients or current case reports – it takes<br />
you only 4 steps to get to the print product desired. Just click under www.sybronimplants.de
ENDOPORE ®<br />
Internal connection<br />
<strong>Endopore</strong> <strong>Implants</strong><br />
<strong>with</strong> internal connection<br />
for one-stage surgery<br />
<br />
The <strong>Endopore</strong> implants have a standard<br />
Morse Taper implant-to-abutment interface<br />
and are supplied in both 4.1 mm and 5.0 mm<br />
implant diameters, each having a 4.8 mm<br />
abutment platform diameter. This allows both<br />
the 4.1 mm and 5.0 mm diameter implants to<br />
accept the same prosthetic components. Each<br />
implant diameter is available <strong>with</strong> a 1.8 mm<br />
transgingival collar. A 1 mm low profile cover<br />
screw is packaged <strong>with</strong> each implant.<br />
AP* TC* Length Item No.<br />
4.8 mm AP*<br />
Implant Ø 4.1 mm<br />
1.8 mm TC*<br />
Length<br />
4.8 mm 1.8 mm 7 mm 01S-7I1.8<br />
4.8 mm 1.8 mm 9 mm 01S-9I1.8<br />
4.8 mm 1.8 mm 12 mm 01S-12I1.8<br />
Implant Ø 5.0 mm<br />
4.8 mm 1.8 mm 5 mm 01WS-5I1.8<br />
* AP – Abutment Platform Ø<br />
** TC – Transgingival Collar<br />
Diameter<br />
4.8 mm 1.8 mm 7 mm 01WS-7I1.8<br />
4.8 mm 1.8 mm 9 mm 01WS-9I1.8<br />
4.8 mm 1.8 mm 12 mm 01WS-12I1.8
Internal connection<br />
BICORTICAL ENDOPORE® ®<br />
Case Planning Chart<br />
One-stage<br />
Surgery<br />
Angled<br />
Cementable<br />
Straight<br />
Cementable<br />
ECO Abutment<br />
Octabutment<br />
<br />
Crown<br />
Bridge<br />
Locking<br />
Non-Locking<br />
Crown<br />
Bridge<br />
Bar
ENDOPORE ®<br />
Internal connection<br />
Case Planning Chart<br />
<br />
One-stage<br />
Surgery<br />
Locator<br />
System<br />
O-Ring<br />
System<br />
Dalla Bona<br />
System<br />
Impression<br />
Stage<br />
Laboratory<br />
Processing<br />
Final<br />
Restoration<br />
Overdenture
Internal connection<br />
BICORTICAL ENDOPORE® ®<br />
Crown and Bridge Restorations<br />
Cover Screws Length Item No.<br />
Cover Screw (replacement)<br />
A 1 mm cover screw is packaged <strong>with</strong> each<br />
implant.<br />
1 mm 02S-1HS<br />
2 mm 02S-2HS<br />
3 mm 02S-3HS<br />
4 mm 02S-4HS<br />
Cementable Abutments Length Item No.<br />
Straight Cementable Abutments<br />
4.0 mm 05S-4.0FS<br />
5.5 mm 05S-5.5FS<br />
7.0 mm 05S-7.0FS<br />
<br />
Angled Cementable Abutments<br />
Angle 15°<br />
Angle 25°<br />
05S-15FA<br />
05S-25FA<br />
15°<br />
ECO Abutment System<br />
ECO Abutment and Cap<br />
for cementable restorations<br />
Length 5.0 mm (7.0 mm <strong>with</strong> cap)<br />
ECO Analog<br />
Item No.<br />
05S-5ABUT/WC<br />
06S-ANALOG<br />
7.0 mm<br />
5.0 mm<br />
ECO Abutment<br />
ECO Analog<br />
ECO Coping – Indexed<br />
ECO Coping – Non Indexed<br />
06S-COPING/I<br />
06S-COPING<br />
ECO Coping<br />
– Indexed<br />
ECO Coping<br />
– Non Indexed
ENDOPORE ®<br />
Internal connection<br />
Octabutment System<br />
Item No.<br />
The Octabutment System is used for all procedures where a removable prosthesis<br />
is required, or where a working model incorporating an abutment analog<br />
is desired.<br />
Octabutment<br />
Octabutment Cap <strong>with</strong> Screw<br />
07S-0010<br />
07S-2100<br />
Octabutment<br />
Cap <strong>with</strong> screw<br />
Transfer Coping<br />
<strong>with</strong> Guide Pin for Octabutment<br />
Octabutment Analog<br />
07S-0090<br />
07S-0015<br />
Transfer Coping<br />
Octabutment Analog<br />
<br />
Temporary Abutment for Octabutment<br />
locking<br />
Temporary Abutment for Octabutment<br />
non-locking<br />
Temporary abutments include an octabutment<br />
retaining screw.<br />
07S-0303<br />
07S-0353<br />
locking<br />
non-locking<br />
Plastic Coping for Octabutment<br />
locking<br />
07S-0203<br />
Plastic Coping for Octabutment<br />
non-locking<br />
07S-0253<br />
locking<br />
non-locking<br />
Note: Plastic copings include an octabutment<br />
retaining screw.<br />
Octabutment Retaining Screw<br />
07S-0053<br />
Accessories<br />
Item No.<br />
Insertion Tip<br />
for the ECO and Cementable Abutment<br />
07S-0176<br />
Insertion Tip for Octabutment<br />
07S-0175<br />
Driver Housing<br />
Driver Tip<br />
0.05“ Hex Tip<br />
07-0190<br />
06-TWHT<br />
Insertion Tip<br />
Insertion Tip for<br />
Octabutment<br />
Driver Housing<br />
0.05“ Hex Tip<br />
Hex Tip<br />
12.5 mm
Internal connection<br />
BICORTICAL ENDOPORE® ®<br />
Overdenture Restorations<br />
Locator Abutments Impl. Ø mm Collar Item No.<br />
The Locator abutment is an attachment <strong>with</strong><br />
a self-aligning feature. This feature will aid<br />
patients in seating their denture and eliminate<br />
additional wear from improper seating.<br />
With the Locator’s minimal vertical height, it<br />
is ideal where interocclusal space is limited.<br />
This abutment can also accommodate up to<br />
40° between implants.<br />
4.1/ 5.0 mm 0.73 mm 8950<br />
4.1/ 5.0 mm 2 mm 8951<br />
4.1/ 5.0 mm 3 mm 8952<br />
4.1/ 5.0 mm 4 mm 8953<br />
4.8 mm<br />
Abutment Platform<br />
Locator Attachments<br />
Item No.<br />
Locator Attachments<br />
Item No.<br />
<br />
Locator Male Processing Package<br />
2 Sets, each Set includes: 1 Processing Replacement<br />
Male 8515, 1 Replacement Male<br />
8524/ 8527/8529, 1 Spacer white<br />
Locator Replacement Male<br />
clear, 4 Pack<br />
Locator Light Retention Replacement Male<br />
pink, 4 Pack<br />
8519<br />
8524<br />
8527<br />
Locator Extended Range Replacement Male<br />
green, 4 Pack<br />
Locator Extra Light Extended Range Male<br />
red, 4 Pack<br />
Locator Black Processing Replacement Male<br />
4 Pack<br />
8547<br />
8548<br />
8515<br />
Locator Extra Light Retention Replacement<br />
Male, blue, 4 Pack<br />
8529<br />
Locator Parallel Post<br />
4 Pack<br />
8517<br />
Locator Impression Coping<br />
4 Pack<br />
8505<br />
Locator Female Analog<br />
5 mm Diameter. 4 Pack<br />
8516<br />
Locator<br />
Parallel Post<br />
Locator Impression<br />
Coping<br />
Female Analog<br />
Ø 5 mm<br />
Angle Measurement Guide<br />
9530<br />
Angle Measurement<br />
Guide<br />
Locator Core Tool<br />
8393<br />
Locator Abutment Driver<br />
15 mm length<br />
21 mm length<br />
8926<br />
8927<br />
20 Ncm Torque Wrench<br />
(Ncm – Newton centimeters)<br />
06-TW20
ENDOPORE ®<br />
Internal connection<br />
Overdenture Restorations<br />
Dalla Bona and O-Ring Abutment Systems<br />
Item No.<br />
The ORS and the Dalla Bona abutments lie<br />
flush <strong>with</strong> the top of the implant when the<br />
abutments are inserted into the <strong>Endopore</strong><br />
One-Stage implants.<br />
Note<br />
Please refer to pages 32 – 33<br />
for Dalla Bona Abutment<br />
System and O-Ring Abutment<br />
System.<br />
10<br />
Dalla Bona Abutment System<br />
Each Dalla Bona System includes a titanium<br />
male abutment, a brass abutment analog, a<br />
titanium female <strong>with</strong> a PVC ring and a spacer.<br />
07S-3000<br />
O-Ring Abutment System<br />
Each O-Ring System includes a titanium male<br />
abutment and an ORS lab kit which includes a<br />
brass abutment analog, metal housing,<br />
3 red O-Rings and 3 white O-Rings.<br />
07S-4000<br />
Note<br />
The red O-Ring is used for<br />
laboratory set-up and the<br />
white O-Ring is used for the<br />
finished overdenture.<br />
Accessories<br />
Item No.<br />
Driver Housing<br />
07-0190<br />
Abutment Driver for ORS and Dalla Bona<br />
System<br />
07-0140<br />
Dalla Bona Activating Tool<br />
An instrument used to increase the retention<br />
of an attachment<br />
07-1017<br />
Dalla Bona Deactivating Tool<br />
An instrument used to reduce the retention of<br />
an attachment<br />
07-1018
Internal <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
11<br />
<strong>Endopore</strong> <strong>Implants</strong> <strong>with</strong><br />
internal <strong>hex</strong> for one-stage<br />
and two-stage surgery<br />
<strong>Endopore</strong> <strong>Implants</strong> <strong>with</strong> internal <strong>hex</strong> are supplied in both 4.1<br />
mm and 5.0 mm implant platforms. A low profile cover screw is<br />
packaged <strong>with</strong> each implant.<br />
SCR* Length Item No.<br />
SCR*<br />
Length<br />
Implant Ø 4.1 mm<br />
2 mm 7 mm 01l-7I2<br />
2 mm 9 mm 01l-9I2<br />
2 mm 12 mm 01l-12I2<br />
Implant Ø 5.0 mm<br />
Diameter<br />
* SCR – Smooth Coronal Region<br />
2 mm 7 mm 01Wl-7I2<br />
2 mm 9 mm 01Wl-9I2<br />
2 mm 12 mm 01Wl-12I2
ENDOPORE ®<br />
Internal <strong>hex</strong><br />
Case Planning Chart<br />
Flared Healing<br />
Straight Healing<br />
12<br />
One- and twostage<br />
Surgery<br />
Abutment<br />
Abutment<br />
Flared Transfer<br />
Straight Transfer<br />
Impression<br />
Stage<br />
Coping Assembly<br />
Coping Assembly<br />
Flared Hexed<br />
Abutment<br />
Angled Hexed<br />
Abutment<br />
Angled Hexed<br />
Abutment<br />
Straight Hexed<br />
Abutment<br />
Hexed UCLA<br />
Abutment<br />
Non-Hexed UCLA<br />
Abutment<br />
Laboratory<br />
Processing<br />
15° 25°<br />
Final<br />
Restoration<br />
Crown<br />
Bridge
Internal <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
13<br />
Case Planning Chart<br />
One- and twostage<br />
Surgery<br />
Straight Healing<br />
Abutment<br />
Impression<br />
Stage<br />
Locator<br />
System<br />
O-Ring<br />
System (ORS)<br />
Dalla Bona<br />
System<br />
Laboratory<br />
Processing<br />
Final<br />
Restoration<br />
Overdenture
ENDOPORE ®<br />
Internal <strong>hex</strong><br />
Crown and Bridge Restorations<br />
Cover Screws Impl. Ø mm Item No.<br />
Cover Screw (replacement)<br />
A low profile cover screw is packaged <strong>with</strong><br />
each implant.<br />
4.1 mm 02I-CS<br />
5.0 mm 02WI-CS<br />
Healing Abutments Impl. Ø mm Length Width Item No.<br />
14<br />
Straight Healing Abutments<br />
The straight healing abutment is used in all<br />
situations except where an expanded gingival<br />
cuff is desired.<br />
4.1 mm 3 mm 4.1 mm 02B-3HS<br />
4.1 mm 5 mm 4.1 mm 02B-5HS<br />
4.1 mm 7 mm 4.1 mm 02B-7HS<br />
5.0 mm 3 mm 5.0 mm 02WB-3HS<br />
5.0 mm 5 mm 5.0 mm 02WB-5HS<br />
5.0 mm 7 mm 5.0 mm 02WB-7HS<br />
Flared Healing Abutments<br />
The use of a flared healing abutment allows<br />
the gingiva to heal around this expanded profile,<br />
where a more natural emergence profile<br />
is preferred.<br />
4.1 mm 4 mm 5.5 mm 02B-4H<br />
4.1 mm 6.5 mm 5.5 mm 02B-6.5H<br />
5.0 mm 4 mm 6.4 mm 02WB-4H<br />
5.0 mm 6.5 mm 6.4 mm 02WB-6.5H<br />
Width<br />
Width<br />
Length<br />
Length<br />
Straight Healing<br />
Abutment<br />
Flared Healing<br />
Abutment
Internal <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
15<br />
Transfer Copings<br />
The shape of the transfer coping matches the<br />
shape of the corresponding healing abutment<br />
and this allows the profile of the gingival cuff<br />
to be accurately reproduced<br />
in the working model.<br />
Transfer Copings Impl. Ø mm Length Item No.<br />
Straight Transfer Copings<br />
for use <strong>with</strong> straight healing abutments,<br />
incl. screw<br />
Flared Transfer Copings<br />
for use <strong>with</strong> flared healing abutments<br />
incl. screw<br />
Transfer Coping Screw, long<br />
for optional use <strong>with</strong> transfer copings, when<br />
an „open tray” technique is used<br />
4.1 mm 11 mm 06I-CTCA/S<br />
5.0 mm 11 mm 06WI-CTCA/S<br />
4.1 mm 11 mm 06I-CTCA/F<br />
5.0 mm 11 mm 06WI-CTCA/F<br />
4.1 mm 16 mm 06B-TC/SL<br />
5.0 mm 16 mm 06B-TC/SL<br />
Straight Transfer<br />
Coping<br />
Flared Transfer<br />
Coping<br />
Transfer Coping<br />
Screw<br />
Implant Analogs Impl. Ø mm Length Qty. Item No.<br />
Implant Analogs<br />
Material: Stainless Steel<br />
4.1 mm 9 mm 1 06I-PIA<br />
5.0 mm 9 mm 1 06WI-PIA<br />
Retaining Screws (replacement) Impl. Ø mm Item No.<br />
for use <strong>with</strong> <strong>hex</strong>ed and UCLA abutments<br />
Titanium Alloy Replacement Screw<br />
Gold Alloy Replacement Screw<br />
4.1/ 5.0 mm 05B-2RS<br />
4.1/ 5.0 mm 05B-2RS/G<br />
All abutments are packaged <strong>with</strong> a titanium<br />
retaining screw.
ENDOPORE ®<br />
Internal <strong>hex</strong><br />
Hexed Abutments Impl. Ø mm Length Collar Item No.<br />
These abutments are used for cement retained<br />
crown or bridge restorations.<br />
Straight Hexed Abutments<br />
Retaining screw included<br />
The straight <strong>hex</strong>ed abutment has a parallel<br />
sided transgingival collar.<br />
4.1 mm 7 mm 1.5 mm 05I-7FN<br />
4.1 mm 9 mm 3.5 mm 05I-9FN<br />
4.1 mm 11 mm 5.5 mm 05I-11FN<br />
5.0 mm 7 mm 1.5 mm 05WI-7FN<br />
5.0 mm 9 mm 3.5 mm 05WI-9FN<br />
5.0 mm 11 mm 5.5 mm 05WI-11FN<br />
Length<br />
Collar<br />
16<br />
Flared Hexed Abutments<br />
Retaining screw included<br />
The flared <strong>hex</strong>ed abutment is designed for<br />
restorations requiring a natural emergence<br />
profile.<br />
4.1 mm 8.5 mm 2 mm 05I-8.5UN<br />
5.0 mm 8.5 mm 2 mm 05WI-8.5UN<br />
Collar<br />
Length<br />
Angled Abutments Impl. Ø mm Length Angle Item No.<br />
Angled Hexed Abutments<br />
Retaining screw included<br />
Angled abutments compensate for large divergences<br />
in implant alignment. Angled guide<br />
pins are available in the Prosthetic Instrumentation<br />
section of this catalog.<br />
4.1 mm 11 mm 15° 05I-15FA<br />
4.1 mm 11 mm 25° 05I-25FA<br />
5.0 mm 11 mm 15° 05WI-15FA<br />
5.0 mm 11 mm 25° 05WI-25FA<br />
15° 25°
Internal <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
17<br />
UCLA Abutments<br />
UCLA abutments provide a foundation to<br />
which wax can be added to shape a screwretained<br />
crown or bridge or a custom abutment.<br />
See the Prosthetic Instrumentation<br />
section for the lapping tool used to polish the<br />
cast surface that will mate <strong>with</strong> the implant.<br />
A reamer is also available to clean out the<br />
retaining screw hole in the casting. Gold base<br />
abutments have machined surfaces and will<br />
not require finishing <strong>with</strong> these tools.<br />
Hexed UCLA abutments should be used for<br />
custom abutments and for supporting crowns<br />
as they will resist the rotational forces associated<br />
<strong>with</strong> single tooth screw retained restorations.<br />
UCLA Abutments Impl. Ø mm Item No.<br />
UCLA Plastic Abutments<br />
Retaining screw included<br />
Hexed<br />
Non-Hexed<br />
UCLA Gold Base Abutments<br />
Non-Ceramic Alloy<br />
Retaining screw included<br />
Hexed<br />
Non-Hexed<br />
4.1 mm 06I-UCLA/H<br />
5.0 mm 06WI-UCLA/H<br />
4.1 mm 06I-UCLA<br />
5.0 mm 06WI-UCLA<br />
4.1 mm 06I-UCLA/H/GNC<br />
5.0 mm 06WI-UCLA/H/GNC<br />
4.1 mm 06I-UCLA/GNC<br />
5.0 mm 06WI-UCLA/GNC<br />
Important<br />
The melting range is 1,400 – 1,490˚C (2,550<br />
– 2,710˚F), refer to package instructions for<br />
further details.<br />
UCLA Plastic<br />
Abutment<br />
Hexed<br />
UCLA Plastic<br />
Abutment<br />
Non-Hexed<br />
UCLA Gold Base<br />
Abutment<br />
Hexed<br />
UCLA Gold Base<br />
Abutment<br />
Non-Hexed
ENDOPORE ®<br />
Internal <strong>hex</strong><br />
Overdenture Restorations<br />
Locator Abutments Impl. Ø mm Collar Item No.<br />
18<br />
The Locator abutment is an attachment <strong>with</strong><br />
a self-aligning feature. This feature will aid<br />
patients in seating their denture and eliminate<br />
additional wear from improper seating.<br />
With the Locator’s minimal vertical height, it<br />
is ideal where interocclusal space is limited.<br />
This abutment can also accommodate up to<br />
40° between implants.<br />
4.1 mm 0 mm 8145<br />
4.1 mm 1 mm 8146<br />
4.1 mm 2 mm 8147<br />
4.1 mm 3 mm 8148<br />
4.1 mm 4 mm 8149<br />
4.1 mm 5 mm 8150<br />
5.0 mm 1 mm 8164<br />
5.0 mm 2 mm 8165<br />
5.0 mm 3 mm 8166<br />
5.0 mm 4 mm 8167<br />
5.0 mm 5 mm 8168<br />
5.0 mm 6 mm 8169<br />
Locator Attachments<br />
Item No.<br />
Locator Attachments<br />
Item No.<br />
Locator Male Processing Package<br />
2 Sets, each Set includes: 1 Processing Replacement<br />
Male 8515, 1 Replacement Male<br />
8524/ 8527/8529, 1 Spacer white<br />
Locator Replacement Male<br />
clear, 4 Pack<br />
Locator Light Retention Replacement Male<br />
pink, 4 Pack<br />
8519<br />
8524<br />
8527<br />
Locator Extended Range Replacement Male<br />
green, 4 Pack<br />
Locator Extra Light Extended Range Male<br />
red, 4 Pack<br />
Locator Black Processing Replacement Male<br />
4 Pack<br />
8547<br />
8548<br />
8515<br />
Locator Extra Light Retention Replacement<br />
Male, blue, 4 Pack<br />
8529<br />
Locator Parallel Post<br />
4 Pack<br />
8517<br />
Locator Impression Coping<br />
4 Pack<br />
8505<br />
Locator Female Analog<br />
4.1 mm Diameter. 4 Pack<br />
5.0 mm Diameter. 4 Pack<br />
8530<br />
8516<br />
Locator<br />
Parallel Post<br />
Locator Impression<br />
Coping<br />
Female Analog<br />
Ø 4.1 mm<br />
Female Analog<br />
Ø 5.0 mm<br />
Angle Measurement Guide<br />
9530<br />
Angle Measurement<br />
Guide<br />
Locator Core Tool<br />
8393<br />
Locator Abutment Driver<br />
15 mm length<br />
21 mm length<br />
8926<br />
8927<br />
20 Ncm Torque Wrench<br />
06-TW20
Internal <strong>hex</strong><br />
BICORTICAL ®<br />
ENDOPORE® 19<br />
O-Ring Abutment System (ORS) Impl. Ø mm Collar Length Item No.<br />
O-Ring Abutment System<br />
The red O-Ring is used for laboratory set-up<br />
and the white O-Ring is used for the finished<br />
overdenture. The O-Ring abutment system can<br />
accommodate up to 5 degrees of divergence<br />
between implants.<br />
Each O-Ring System includes a titanium male<br />
abutment and an ORS lab kit which includes<br />
a brass abutment analog, metal housing,<br />
3 red O-Rings and 3 white O-Rings.<br />
Note<br />
Please refer to page 32 for O-Ring Abutment<br />
System.<br />
Ø 4.1 1 mm 4 mm 04I-1ORS<br />
Ø 4.1 2 mm 5 mm 04I-2ORS<br />
Ø 4.1 3 mm 6 mm 04I-3ORS<br />
Ø 4.1 4 mm 7 mm 04I-4ORS<br />
Ø 4.1 5 mm 8 mm 04I-5ORS<br />
Ø 4.1 6 mm 9 mm 04I-6ORS<br />
Ø 4.1 7 mm 10 mm 04I-7ORS<br />
Ø 5.0 1 mm 4 mm 04WI-1ORS<br />
Ø 5.0 2 mm 5 mm 04WI-2ORS<br />
Ø 5.0 3 mm 6 mm 04WI-3ORS<br />
Ø 5.0 4 mm 7 mm 04WI-4ORS<br />
Ø 5.0 5 mm 8 mm 04WI-5ORS<br />
Ø 5.0 5 mm 9 mm 04WI-6ORS<br />
O-Ring Accessories Item No. Item No.<br />
O-Ring Lab Kit<br />
Metal Housing<br />
06-ORS<br />
07-0044<br />
White O-Rings<br />
Package of 10<br />
06-O/ORS<br />
Dalla Bona Abutment System Impl. Ø mm Collar Length Item No.<br />
Dalla Bona Abutment System<br />
The Dalla Bona abutment is a ball & socket<br />
type connector. Its spherical design allows<br />
up to 15 degrees divergence between the<br />
abutments.<br />
Each Dalla Bona System includes a titanium<br />
male abutment, a brass abutment analog,<br />
a titanium female <strong>with</strong> a PVC ring and a<br />
spacer.<br />
Note<br />
Please refer to page 33 for Dalla Bona Abutment<br />
System.<br />
Dalla Bona Accessories<br />
Dalla Bona Replacement Female Cap<br />
Includes a brass abutment analog, a titanium<br />
female <strong>with</strong> a PVC ring and a spacer.<br />
Ø 4.1 1 mm 4 mm 04I-1DB<br />
Ø 4.1 2 mm 5 mm 04I-2DB<br />
Ø 4.1 3 mm 6 mm 04I-3DB<br />
Ø 4.1 4 mm 7 mm 04I-4DB<br />
Ø 4.1 5 mm 8 mm 04I-5DB<br />
Ø 4.1 6 mm 9 mm 04I-6DB<br />
Ø 4.1 7 mm 10 mm 04I-7DB<br />
Ø 5.0 1 mm 4 mm 04WI-1DB<br />
Ø 5.0 2 mm 5 mm 04WI-2DB<br />
Ø 5.0 3 mm 6 mm 04WI-3DB<br />
Ø 5.0 4 mm 7 mm 04WI-4DB<br />
Ø 5.0 5 mm 8 mm 04WI-5DB<br />
Ø 5.0 6 mm 9 mm 04WI-6DB<br />
Ø 5.0 7 mm 10 mm 04WI-7DB<br />
Item No.<br />
07-1012<br />
Dalla Bona Activating Tool<br />
An instrument used to increase the retention<br />
of an attachment.<br />
07-1017<br />
Dalla Bona Deactivating Tool<br />
An instrument used to reduce the retention of<br />
an attachment.<br />
07-1018
ENDOPORE ®<br />
Internal <strong>hex</strong><br />
UMA System Impl. Ø mm Collar Item No.<br />
UMA System Abutments<br />
The UMA (Universal Modification Abutment)<br />
system is used for screw retained restorations<br />
where it is desired to have the points of<br />
attachment superior to the soft tissue. Where<br />
there is insufficient clearance to use a UMA<br />
or when a sub-gingival separation is desired,<br />
a UCLA abutment can be used to achieve separation<br />
of the restoration at the implant level.<br />
The UMA is a transmucosal collar that should<br />
be secured to the implant <strong>with</strong> 30 Ncm of<br />
torque. The UMA screw used to secure the<br />
restoration to the abutment is packaged <strong>with</strong><br />
each UMA plastic coping. A 0.05“ <strong>hex</strong> driver<br />
is used to secure the screw which should<br />
only be tightened to 20 Ncm.<br />
Ø 4.1 2.0 mm 02I-2.0UMA<br />
Ø 4.1 3.0 mm 02I-3.0UMA<br />
Ø 4.1 4.0 mm 02I-4.0UMA<br />
Ø 4.1 5.0 mm 02I-5.0UMA<br />
Ø 4.1 6.0 mm 02I-6.0UMA<br />
Ø 4.1 7.0 mm 02I-7.0UMA<br />
Ø 4.1 8.0 mm 02I-8.0UMA<br />
Ø 5.0 3.0 mm 02WI-3.0UMA<br />
Ø 5.0 4.0 mm 02WI-4.0UMA<br />
Ø 5.0 5.0 mm 02WI-5.0UMA<br />
Ø 5.0 6.0 mm 02WI-6.0UMA<br />
Note<br />
Please refer to pages 34 – 35 for UMA<br />
System.<br />
20
External <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
21<br />
<strong>Endopore</strong> <strong>Implants</strong> <strong>with</strong><br />
<strong>external</strong> <strong>hex</strong> for one-stage<br />
and two-stage surgery<br />
<strong>Endopore</strong> <strong>Implants</strong> <strong>with</strong> <strong>external</strong> <strong>hex</strong> are compatible <strong>with</strong> a<br />
wide variety of prosthetic products for crown and bridge and<br />
overdenture restorations including UCLA, UMA, Dalla Bona,<br />
Overdenture and O-Ring Abutment Systems. All implants are<br />
packaged <strong>with</strong> colour coded labels that identify their diameters.<br />
All prosthetic components must be matched to the<br />
diameter of implant to which they are to be connected. Abutment<br />
labels have the same color coding as the corresponding<br />
implants.
ENDOPORE ®<br />
External <strong>hex</strong><br />
<strong>Endopore</strong> <strong>Implants</strong> <strong>with</strong> <strong>external</strong> <strong>hex</strong><br />
22<br />
The <strong>Endopore</strong> External Hex Connection implants are available<br />
in three diameters: 3.5 mm, 4.1 mm and 5.0 mm.<br />
A low profile cover screw is packaged <strong>with</strong> each implant. The<br />
4.1 mm and 5.0 mm diameter are available <strong>with</strong> a 1 mm or 2<br />
mm smooth coronal region. The 3.5 mm diameter implant is<br />
available in a 1 mm smooth coronal region.<br />
SCR*<br />
Length<br />
3.5 mm diameter implant<br />
The 3.5 mm diameter implant is packaged in a red labeled box<br />
(01M-range). This implant has a 0.9 mm high x 2.0 mm flat-toflat<br />
<strong>hex</strong> and a UNF thread.<br />
4.1 mm diameter implant<br />
The 4.1 mm diameter implants <strong>with</strong> the industry standard <strong>hex</strong><br />
are packaged in green labeled boxes (01B-range). These<br />
implants have a 0.7 mm high x 2.7 mm flat-to-flat <strong>hex</strong> and a<br />
metric thread.<br />
5.0 mm diameter implant<br />
The 5.0 mm diameter implants are packaged in turquoise<br />
labeled boxes (01WB-range). These implants have a 0.9 mm<br />
high x 2.7 mm flat-to-flat <strong>hex</strong> and metric thread.<br />
Diameter<br />
SCR* 1 mm<br />
Length<br />
SCR* Length Item No.<br />
Implant Ø 3.5 mm<br />
1 mm 9 mm 01M-9I1<br />
Implant Ø 4.1 mm<br />
* SCR – Smooth Coronal Region<br />
Diameter<br />
Diameter<br />
SCR* 2 mm<br />
Length<br />
1 mm 7 mm 01B-7I1<br />
2 mm 7 mm 01B-7I2<br />
1 mm 9 mm 01B-9I1<br />
2 mm 9 mm 01B-9I2<br />
1 mm 12 mm 01B-12I1<br />
2 mm 12 mm 01B-12I2<br />
Implant Ø 5.0 mm<br />
1 mm 5 mm 01WB-5I1<br />
1 mm 7 mm 01WB-7I1<br />
2 mm 7 mm 01WB-7I2<br />
1 mm 9 mm 01WB-9I1<br />
2 mm 9 mm 01WB-9I2<br />
1 mm 12 mm 01WB-12I1<br />
2 mm 12 mm 01WB-12I2
External <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
23<br />
Case Planning Chart<br />
One- and twostage<br />
Surgery<br />
Flared Healing<br />
Abutment<br />
Straight Healing<br />
Abutment<br />
Impression<br />
Stage<br />
Flared Transfer<br />
Coping Assembly<br />
Straight Transfer<br />
Coping Assembly<br />
Flared Hexed<br />
Abutment<br />
Angled Hexed<br />
Abutment<br />
Angled Hexed<br />
Abutment<br />
Straight Hexed<br />
Abutment<br />
Hexed UCLA<br />
Abutment<br />
Non-Hexed UCLA<br />
Abutment<br />
Laboratory<br />
Processing<br />
15° 25°<br />
Final<br />
Restoration<br />
Crown<br />
Bridge
ENDOPORE ®<br />
External <strong>hex</strong><br />
Case Planning Chart<br />
One- and twostage<br />
Surgery<br />
Straight Healing<br />
Abutment<br />
24<br />
Impression<br />
Stage<br />
Locator<br />
System<br />
O-Ring<br />
System<br />
Dalla Bona<br />
System<br />
Laboratory<br />
Processing<br />
Final<br />
Restoration<br />
Overdenture
External <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
25<br />
Case Planning Chart<br />
UMA Healing Cap<br />
One- and twostage<br />
Surgery<br />
Standard UMA System Abutment<br />
Impression<br />
Stage<br />
Single Crown<br />
Bridge, Bar and Clip<br />
O-Ring<br />
Step 1<br />
Step 1<br />
Step 2<br />
Step 2<br />
Laboratory<br />
Processing<br />
Final<br />
Restoration<br />
Crown<br />
Bridge<br />
Bar<br />
Overdenture
ENDOPORE ®<br />
External <strong>hex</strong><br />
Crown and Bridge Restorations<br />
Cover Screws Impl. Ø mm Item No.<br />
Cover Screw (replacement)<br />
A low profile cover screw is packaged <strong>with</strong><br />
each implant.<br />
3.5 mm 02M-CS<br />
4.1 mm 02B-CS<br />
5.0 mm 02WB-CS<br />
Healing Abutments Impl. Ø mm Length Width Item No.<br />
26<br />
Straight Healing Abutments<br />
The straight healing abutment is used in all<br />
situations except where an expanded gingival<br />
cuff is desired.<br />
Ø 3.5 3 mm 3.5 mm 02M-3HS<br />
Ø 3.5 5 mm 3.5 mm 02M-5HS<br />
Ø 3.5 7 mm 3.5 mm 02M-7HS<br />
Ø 4.1 3 mm 4.1 mm 02B-3HS<br />
Ø 4.1 5 mm 4.1 mm 02B-5HS<br />
Ø 4.1 7 mm 4.1 mm 02B-7HS<br />
Ø 5.0 3 mm 5.0 mm 02WB-3HS<br />
Ø 5.0 5 mm 5.0 mm 02WB-5HS<br />
Ø 5.0 7 mm 5.0 mm 02WB-7HS<br />
Flared Healing Abutments<br />
The use of a flared healing abutment allows<br />
the gingiva to heal around this expanded profile,<br />
where a more natural emergence profile<br />
is preferred.<br />
Ø 3.5 4 mm 4.7 mm 02M-4H<br />
Ø 3.5 6.5 mm 4.7 mm 02M-6.5H<br />
Ø 4.1 4 mm 5.5 mm 02B-4H<br />
Ø 4.1 6.5 mm 5.5 mm 02B-6.5H<br />
Ø 5.0 4 mm 6.4 mm 02WB-4H<br />
Ø 5.0 6.5 mm 6.4 mm 02WB-6.5H<br />
Width<br />
Width<br />
Length<br />
Length<br />
Straight Healing<br />
Abutment<br />
Flared Healing<br />
Abutment
External <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
27<br />
Transfer Copings Impl. Ø mm Length Width Item No.<br />
The shape of the transfer coping matches the<br />
shape of the corresponding healing abutment<br />
and this allows the profile of the gingival cuff<br />
to be accurately reproduced<br />
in the working model.<br />
Straight Transfer Copings<br />
for use <strong>with</strong> straight healing abutments<br />
Ø 3.5 11 mm 3.5 mm 06M-CTCA/S<br />
Ø 3.5 16 mm 3.5 mm 06M-CTCA/SL<br />
Ø 4.1 11 mm 4.1 mm 06B-CTCA/S<br />
Ø 4.1 16 mm 4.1 mm 06B-CTCA/SL<br />
Ø 5.0 11 mm 5.0 mm 06WB-CTCA/S<br />
Ø 5.0 16 mm 5.0 mm 06WB-CTCA/SL<br />
Flared Transfer Copings<br />
for use <strong>with</strong> flared healing abutments<br />
Ø 3.5 11 mm 4.7 mm 06M-CTCA/F<br />
Ø 4.1 11 mm 5.5 mm 06B-CTCA/F<br />
Ø 4.1 16 mm 5.5 mm 06B-CTCA/FL<br />
Ø 5.0 11 mm 6.4 mm 06WB-CTCA/F<br />
Transfer Coping Screw, long<br />
for optional use <strong>with</strong> transfer copings, when<br />
an „open tray” technique is used<br />
Ø 3.5 16 mm 06-TC/SL<br />
Ø 4.1 16 mm 06B-TC/SL<br />
Ø 5.0 16 mm 06B-TC/SL<br />
Closed Impression<br />
Straight Transfer Copings 11 mm<br />
Flared Transfer Copings 11 mm<br />
marking<br />
marking<br />
marking<br />
marking<br />
marking<br />
marking<br />
Ø 3.5<br />
Ø 4.1 Ø 5.0 Ø 3.5 Ø 4.1 Ø 5.0<br />
Open Impression<br />
Transfer Coping Screw for optional use 16 mm<br />
marking<br />
Ø 3.5 Ø 4.1<br />
Ø 5.0
ENDOPORE ®<br />
External <strong>hex</strong><br />
Implant Analogs Impl. Ø mm Length Qty. Item No.<br />
Implant Analogs<br />
Material: Aluminum<br />
Ø 3.5 9 mm 1 06M-IA/1<br />
Ø 3.5 9 mm 5 06M-IA<br />
Ø 4.1 9 mm 1 06B-IA/1<br />
Ø 4.1 9 mm 5 06B-IA<br />
Ø 5.0 9 mm 1 06WB-IA/1<br />
Ø 5.0 9 mm 5 06WB-IA<br />
Implant Analog<br />
Material: Stainless Steel<br />
Ø 3.5 9 mm 1 06M-PIA<br />
Ø 3.5 9 mm 5 06M-PIA/5<br />
Ø 4.1 9 mm 1 06B-PIA<br />
Ø 4.1 9 mm 5 06B-PIA/5<br />
Ø 5.0 9 mm 1 06WB-PIA<br />
Ø 5.0 9 mm 5 06WB-PIA/5<br />
28<br />
Aluminum<br />
Stainless Steel<br />
Ø 3.5 Ø 4.1 Ø 5.0 Ø 3.5 Ø 4.1 Ø 5.0<br />
Retaining Screws Impl. Ø mm Item No.<br />
Retaining Screw (replacement)<br />
for use <strong>with</strong> <strong>hex</strong>ed and UCLA abutments<br />
Titanium Alloy Replacement Screw<br />
Ø 3.5<br />
Ø 4.1/5.0<br />
05-2RS<br />
05B-2RS<br />
Gold Alloy Replacement Screw<br />
Ø 3.5<br />
Ø 4.1/5.0<br />
05M-2RS/G<br />
05B-2RS/G<br />
All abutments are packaged <strong>with</strong> a titanium<br />
retaining screw.
External <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
29<br />
Hexed Abutments Impl. Ø mm Length Collar Item No.<br />
These abutments are used for cement retained<br />
crown or bridge restorations.<br />
Straight Hexed Abutments<br />
Retaining screw included<br />
The straight <strong>hex</strong>ed abutment has a parallel<br />
sided transgingival collar. These abutments<br />
are available in both regular (grooved – FS)<br />
and thick wall (not grooved – FN) versions.<br />
Ø 3.5 7 mm 1.5 mm 05M-7FS<br />
Ø 3.5 7 mm 1.5 mm 05M-7FN<br />
Ø 3.5 9 mm 3.5 mm 05M-9FN<br />
Ø 4.1 7 mm 1.5 mm 05B-7FS<br />
Ø 4.1 7 mm 1.5 mm 05B-7FN<br />
Ø 4.1 9 mm 3.5 mm 05B-9FS<br />
Ø 4.1 9 mm 3.5 mm 05B-9FN<br />
Ø 4.1 11 mm 5.5 mm 05B-11FS<br />
Ø 4.1 11 mm 5.5 mm 05B-11FN<br />
Ø 5.0 7 mm 1.5 mm 05WB-7FS<br />
Ø 5.0 7 mm 1.5 mm 05WB-7FN<br />
Ø 5.0 9 mm 3.5 mm 05WB-9FS<br />
Ø 5.0 9 mm 3.5 mm 05WB-9FN<br />
Ø 5.0 11 mm 5.5 mm 05WB-11FS<br />
Ø 5.0 11 mm 5.5 mm 05WB-11FN<br />
Length<br />
Length<br />
Collar<br />
FN<br />
FS<br />
Flared Hexed Abutments<br />
Retaining screw included<br />
The flared <strong>hex</strong>ed abutment is designed for<br />
restorations requiring a natural emergence<br />
profile. These abutments are available in both<br />
regular (grooved – UF) and thick wall (not<br />
grooved – UN) versions.<br />
Ø 3.5 8.5 mm 2 mm 05M-8.5UN<br />
Ø 3.5 9 mm 2 mm 05M-9UF<br />
Ø 4.1 8.5 mm 2 mm 05B-8.5UN<br />
Ø 4.1 10 mm 2 mm 05B-10UF<br />
Ø 4.1 11.5 mm 3.5 mm 05B-11.5UN<br />
Ø 5.0 8.5 mm 1.5 mm 05WB-8.5UN<br />
Ø 5.0 8 mm 1.5 mm 05WB-8UF<br />
Ø 5.0 10.5 mm 3.5 mm 05WB-10.5UN<br />
Length<br />
Length<br />
Collar<br />
UN<br />
UF
ENDOPORE ®<br />
External <strong>hex</strong><br />
Hexed Abutments Impl. Ø mm Length Angle Item No.<br />
Angled Hexed Abutments<br />
Retaining screw included<br />
Angled abutments compensate for large divergences<br />
in implant alignment. Angled guide<br />
pins are available in the Prosthetic Instrumentation<br />
section of this catalog, pages 36 – 37.<br />
Ø 3.5 11 mm 15˚ 05M-15FA<br />
Ø 3.5 11 mm 25˚ 05M-25FA<br />
Ø 4.1 11 mm 15˚ 05B-15FA<br />
Ø 4.1 11 mm 25˚ 05B-25FA<br />
Ø 5.0 11 mm 15˚ 05WB-15FA<br />
Ø 5.0 11 mm 25˚ 05WB-25FA<br />
15°<br />
25°<br />
Temporary Titanium Abutments Impl. Ø mm Item No.<br />
30<br />
Temporary Abutments<br />
Retaining screw included<br />
Hexed Temporary Abutment<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
05M-TEMP/H<br />
05B-TEMP/H<br />
05WB-TEMP/H<br />
Non-Hexed Temporary Abutment<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
05M-TEMP<br />
05B-TEMP<br />
05WB-TEMP
External <strong>hex</strong><br />
Crown and Bridge Restorations<br />
UCLA Abutments<br />
UCLA abutments provide a foundation to which wax can be<br />
added to shape a screw-retained crown or bridge or a custom<br />
abutment. See the Prosthetic Instrumentation section for the<br />
lapping tool used to polish the cast surface that will mate <strong>with</strong><br />
the implant. A reamer is also available to clean out the retaining<br />
screw hole in the casting. Gold base abutments have ma-<br />
BICORTICAL ENDOPORE® ®<br />
chined surfaces and will not require finishing <strong>with</strong> these tools.<br />
Hexed UCLA abutments should be used for custom abutments<br />
and for supporting crowns as they will resist the rotational<br />
forces associated <strong>with</strong> single tooth screw retained restorations.<br />
Non-<strong>hex</strong>ed UCLA abutments should be used for supporting<br />
screw retained bridges.<br />
31<br />
UCLA Abutments Impl. Ø mm Item No.<br />
UCLA Plastic Abutments<br />
Retaining screw included<br />
Hexed, green<br />
Hexed, yellow<br />
Hexed, blue<br />
Non-Hexed, white<br />
Non-Hexed, white<br />
Non-Hexed, yellow<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
06M-UCLA/H<br />
06B-UCLA/H<br />
06WB-UCLA/H<br />
06M-UCLA<br />
06B-UCLA<br />
06WB-UCLA<br />
Hexed<br />
Non-Hexed<br />
UCLA Gold Base Abutments, metal alloy for<br />
porcelain fusing<br />
Retaining screw included<br />
Important<br />
The melting range is 1232 – 1260˚C (2250 – 2300˚F), refer to package instructions<br />
for further details.<br />
Hexed<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
06M-UCLA/H/G<br />
06B-UCLA/H/G<br />
06WB-UCLA/H/G<br />
Non-Hexed<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
06M-UCLA/G<br />
06B-UCLA/G<br />
06WB-UCLA/G<br />
Hexed<br />
Non-Hexed<br />
UCLA Gold Base Abutments, alloy not for<br />
porcelain fusing<br />
Retaining screw included<br />
Hexed Gold Base UCLA Abutment<br />
Important<br />
The melting range is 1400 – 1490˚C (2550 – 2710˚F), refer to package instructions<br />
for further details.<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
06M-UCLA/H/GNC<br />
06B-UCLA/H/GNC<br />
06WB-UCLA/H/GNC<br />
Non-Hexed Gold Base UCLA Abutment<br />
Ø 3.5<br />
Ø 4.1<br />
Ø 5.0<br />
06M-UCLA/GNC<br />
06B-UCLA/GNC<br />
06WB-UCLA/GNC<br />
Hexed<br />
Non-Hexed
ENDOPORE ®<br />
External <strong>hex</strong><br />
Overdenture Restorations<br />
Locator System Impl. Ø mm Collar Item No.<br />
32<br />
The Locator abutment is an attachment <strong>with</strong><br />
a self-aligning feature. This feature will aid<br />
patients in seating their denture and eliminate<br />
additional wear from improper seating.<br />
With the Locator’s minimal vertical height, it<br />
is ideal where interocclusal space is limited.<br />
This abutment can also accommodate up to<br />
40° between implants.<br />
Note<br />
Please refer to pages 9 and 18 for Locator<br />
System and its components.<br />
3.5 mm 1 mm 8851<br />
3.5 mm 2 mm 8852<br />
3.5 mm 3 mm 8853<br />
3.5 mm 4 mm 8854<br />
4.1 mm 0.73 mm 8681<br />
4.1 mm 2 mm 8682<br />
4.1 mm 3 mm 8683<br />
4.1 mm 4 mm 8684<br />
5.0 mm 1.35 mm 8691<br />
5.0 mm 2 mm 8691<br />
5.0 mm 3 mm 8691<br />
5.0 mm 4 mm 8691<br />
O-Ring Abutment System (ORS) Impl. Ø mm Collar Length Item No.<br />
O-Ring Abutment System<br />
The O-Ring abutment system can accommodate<br />
up to 5 degrees of divergence between<br />
implants.<br />
Each O-Ring System includes a titanium male<br />
abutment and an ORS lab kit which includes<br />
a brass abutment analog, metal housing,<br />
3 red O-Rings and 3 white O-Rings.<br />
Length<br />
Note<br />
The red O-Ring is used for laboratory set-up<br />
and the white O-Ring is used for the finished<br />
overdenture.<br />
O-Ring Accessories<br />
O-Ring Lab Kit<br />
Metal Housing<br />
White O-Rings<br />
Package of 10<br />
Collar<br />
Ø 3.5 1 mm 4 mm 04M-1ORS<br />
Ø 3.5 2 mm 5 mm 04M-2ORS<br />
Ø 3.5 3 mm 6 mm 04M-3ORS<br />
Ø 3.5 4 mm 7 mm 04M-4ORS<br />
Ø 3.5 5 mm 8 mm 04M-5ORS<br />
Ø 4.1 1 mm 4 mm 04B-1ORS<br />
Ø 4.1 2 mm 5 mm 04B-2ORS<br />
Ø 4.1 3 mm 6 mm 04B-3ORS<br />
Ø 4.1 4 mm 7 mm 04B-4ORS<br />
Ø 4.1 5 mm 8 mm 04B-5ORS<br />
Ø 4.1 6 mm 9 mm 04B-6ORS<br />
Ø 4.1 7 mm 10 mm 04B-7ORS<br />
Ø 5.0 1 mm 4 mm 04WB-1ORS<br />
Ø 5.0 2 mm 5 mm 04WB-2ORS<br />
Ø 5.0 3 mm 6 mm 04WB-3ORS<br />
Ø 5.0 4 mm 7 mm 04WB-4ORS<br />
Ø 5.0 5 mm 8 mm 04WB-5ORS<br />
Ø 5.0 6 mm 9 mm 04WB-6ORS<br />
Item No.<br />
06-ORS<br />
07-0044<br />
06-O/ORS
External <strong>hex</strong><br />
BICORTICAL ENDOPORE® ®<br />
33<br />
Dalla Bona Abutment System Impl. Ø mm Collar Length Item No.<br />
Dalla Bona Abutment System<br />
The Dalla Bona abutment is a ball & socket<br />
type connector. Its spherical design allows<br />
up to 15 degrees divergence between the<br />
abutments.<br />
Each Dalla Bona System includes a titanium<br />
male abutment, a brass abutment analog,<br />
a titanium female <strong>with</strong> a PVC ring and a<br />
spacer.<br />
Length<br />
Collar<br />
Dalla Bona Plus Accessories<br />
Dalla Bona Plus<br />
Keeping the same benefits as the Dalla<br />
Bona System, the Dalla Bona Plus female attachment<br />
is a gold insert that can be easily<br />
replaced and adjusted <strong>with</strong> Dalla Bona Plus<br />
Activating/Deactivating Tool. Includes a brass<br />
abutment analog, a titanium cap <strong>with</strong> a gold<br />
female insert, and a spacer.<br />
Dalla Bona Plus Activating/Deactivating Tool<br />
An instrument used to increase and reduce<br />
the retention of an attachment.<br />
Ø 3.5 1 mm 4 mm 04M-1DB<br />
Ø 3.5 2 mm 5 mm 04M-2DB<br />
Ø 3.5 3 mm 6 mm 04M-3DB<br />
Ø 3.5 4 mm 7 mm 04M-4DB<br />
Ø 3.5 5 mm 8 mm 04M-5DB<br />
Ø 3.5 6 mm 9 mm 04M-6DB<br />
Ø 3.5 7 mm 10 mm 04M-7DB<br />
Ø 4.1 1 mm 4 mm 04B-1DB<br />
Ø 4.1 2 mm 5 mm 04B-2DB<br />
Ø 4.1 3 mm 6 mm 04B-3DB<br />
Ø 4.1 4 mm 7 mm 04B-4DB<br />
Ø 4.1 5 mm 8 mm 04B-5DB<br />
Ø 4.1 6 mm 9 mm 04B-6DB<br />
Ø 4.1 7 mm 10 mm 04B-7DB<br />
Ø 5.0 1 mm 4 mm 04WB-1DB<br />
Ø 5.0 2 mm 5 mm 04WB-2DB<br />
Ø 5.0 3 mm 6 mm 04WB-3DB<br />
Ø 5.0 4 mm 7 mm 04WB-4DB<br />
Ø 5.0 5 mm 8 mm 04WB-5DB<br />
Ø 5.0 6 mm 9 mm 04WB-6DB<br />
Ø 5.0 7 mm 10 mm 04WB-7DB<br />
Item No.<br />
07-0480<br />
07-0489<br />
Dalla Bona Accessories<br />
Dalla Bona Replacement Female Cap<br />
Includes a brass abutment analog, a titanium<br />
female <strong>with</strong> a PVC ring and a spacer.<br />
Item No.<br />
07-1012<br />
Dalla Bona Activating Tool<br />
An instrument used to increase the retention<br />
of an attachment.<br />
07-1017<br />
Dalla Bona Deactivating Tool<br />
An instrument used to reduce the retention of<br />
an attachment.<br />
07-1018
ENDOPORE ®<br />
External <strong>hex</strong><br />
UMA System Impl. Ø mm Collar Item No.<br />
34<br />
UMA System Abutments<br />
The UMA (Universal Modification Abutment)<br />
system is used for screw retained restorations<br />
where it is desired to have the points of<br />
attachment superior to the soft tissue. Where<br />
there is insufficient clearance to use a UMA<br />
or when a sub-gingival separation is desired,<br />
a UCLA abutment can be used to achieve separation<br />
of the restoration at the implant level.<br />
The UMA is a transmucosal collar that should<br />
be secured to the implant <strong>with</strong> 30 Ncm of<br />
torque. The UMA screw used to secure the<br />
restoration to the abutment is packaged <strong>with</strong><br />
each UMA plastic coping. A 0.05“ <strong>hex</strong> driver<br />
is used to secure the screw which should<br />
only be tightened to 20 Ncm.<br />
Standard UMA System Abutment<br />
The upper diameter for all UMA System<br />
Abutments is 3.85 mm.<br />
Ø 3.5 3.5 mm 02M-3.5UMA<br />
Ø 3.5 4.5 mm 02M-4.5UMA<br />
Ø 3.5 5.5 mm 02M-5.5UMA<br />
Ø 3.5 6.5 mm 02M-6.5UMA<br />
Ø 4.1 2.5 mm 02B-2.5UMA<br />
Ø 4.1 3.0 mm 02B-3.0UMA<br />
Ø 4.1 4.0 mm 02B-4.0UMA<br />
Ø 4.1 5.0 mm 02B-5.0UMA<br />
Ø 4.1 6.0 mm 02B-6.0UMA<br />
Ø 4.1 7.0 mm 02B-7.0UMA<br />
Ø 4.1 8.0 mm 02B-8.0UMA<br />
Ø 5.0 3.5 mm 02WB-3.5UMA<br />
Ø 5.0 4.5 mm 02WB-4.5UMA<br />
Ø 5.0 5.5 mm 02WB-5.5UMA<br />
Ø 5.0 6.5 mm 02WB-6.5UMA<br />
Collar<br />
UMA Healing Cap<br />
Item No.<br />
UMA Healing Cap<br />
2 mm length<br />
07-2120<br />
UMA Transfer Copings<br />
Item No.<br />
UMA Hexed Transfer Coping<br />
Single tooth open tray<br />
UMA Guide Pin<br />
für 07-0090<br />
07-0090<br />
07-0062<br />
UMA Non-Hexed Transfer Coping<br />
for bridge construction<br />
07-0080
External <strong>hex</strong><br />
BICORTICAL ®<br />
UMA Analogs<br />
Item No.<br />
Brass<br />
07-0015<br />
Stainless Steel<br />
UMA retaining screw included<br />
07-0162<br />
Brass<br />
Stainless Steel<br />
UMA Copings<br />
Item No.<br />
UMA Temporary Non-Hexed Coping<br />
UMA retaining screw included<br />
07-0352<br />
UMA Hexed Plastic Coping<br />
UMA retaining screw included<br />
blue<br />
07-0202<br />
UMA Non-Hexed Plastic Coping<br />
UMA retaining screw included<br />
yellow<br />
07-0252<br />
UMA Non-Hexed Gold Coping<br />
UMA retaining screw included<br />
07-0252/G<br />
UMA Temporary<br />
Non-Hexed Coping<br />
UMA Hexed Plastic<br />
Coping<br />
UMA Non-Hexed<br />
Plastic Coping<br />
ENDOPORE® 35<br />
UMA Non-Hexed<br />
Gold Coping<br />
UMA Replacement Components<br />
Item No.<br />
UMA Non-Hexed Plastic Coping<br />
for Bar<br />
07-0270<br />
UMA Retaining Screw<br />
07-0052<br />
Gold Plated Bar Clip<br />
CM Rider<br />
07-0120<br />
UMA Hexed Plastic<br />
Coping<br />
UMA<br />
Retaining Srew<br />
Gold Plated<br />
Bar Clip<br />
UMA Bar Kit<br />
Item No.<br />
UMA Bar Kit<br />
Includes 4 bars, a spacer bar, 4 retaining<br />
screws, 4 plastic cylinders, and 4 gold plated<br />
clips<br />
07-5540<br />
UMA O-Ring System<br />
Item No.<br />
UMA O-Ring System<br />
Each abutment is packaged <strong>with</strong> an ORS lab kit<br />
that includes a brass abutment analog, metal<br />
housing, 3 red O-Rings and 3 white O-Rings.<br />
07-4400<br />
Note<br />
The red O-Ring is used for<br />
laboratory set-up and the<br />
white O-Ring is used for the<br />
finished overdenture.
ENDOPORE ®<br />
Prosthetics<br />
Prosthetic Instrumentation<br />
Item No.<br />
Hex Driver, 0.05“<br />
extra short, 9 mm<br />
short, 13 mm<br />
long, 18 mm<br />
06-HDXS<br />
06-HDS<br />
06-HDL<br />
36<br />
9 mm<br />
13 mm<br />
18 mm<br />
extra short short long<br />
30 Ncm Torque Wrench<br />
20 Ncm Torque Wrench<br />
For use <strong>with</strong> UMA System and Locator System<br />
(Ncm – Newton centimeters)<br />
06-TW30<br />
06-TW20<br />
Driver Housing<br />
Driver Extension<br />
07-0190<br />
07-0195<br />
Driver Housing<br />
Driver Extension<br />
Driver Tips<br />
fit Driver Housing and Torque Wrenches<br />
0.05“ Hex Tip<br />
06-TWHT<br />
0.05“ Hex Tip – Short<br />
06-TWHTS<br />
UMA Abutment Driver<br />
ORS and Dalla Bona Abutment Driver<br />
07-1150<br />
07-0140<br />
Hex Tip<br />
12.5 mm<br />
Hex Tip short<br />
6.5 mm<br />
UMA Abutment<br />
Driver<br />
ORS-, Dalla Bona<br />
Abutment Driver
Prosthetics<br />
BICORTICAL ENDOPORE® ®<br />
37<br />
Prosthetic Instrumentation<br />
Latch Driver<br />
0.05“ Hex Latch Type Driver<br />
Item No.<br />
07-0125<br />
UMA Friction Grip Driver<br />
Friction driver for UMA non-<strong>hex</strong>ed transfer<br />
coping and UMA O-Ring Abutment<br />
07-0004<br />
Guide Pin<br />
for angled abutment selection<br />
15° angled<br />
25° angled<br />
06-15AAGP<br />
06-25AAGP<br />
15°<br />
25°<br />
Reamer<br />
for use <strong>with</strong> UMA abutment castings<br />
for use <strong>with</strong> UCLA abutment castings<br />
07-0150<br />
06-REM<br />
Lapping Tool <strong>with</strong> guide pin<br />
for use <strong>with</strong> UMA and UCLA abutment castings<br />
and all platforms<br />
07-0155WP<br />
Waxing Sleeve<br />
06-WS
ENDOPORE ®<br />
Surgery<br />
Surgery<br />
38<br />
Comprehensive Surgical Kit<br />
Surgical Instrument Tray, fully equipped<br />
06-ITSTART<br />
Content of a full equipped tray<br />
2.3 mm Round Bur 06-RB<br />
2.5 mm Twist Drill – short 06-2.5TDS<br />
2.5 mm Twist Drill – long 06-2.5TDL<br />
3.5 mm Implant Bur, 9 mm 06M-9IB<br />
4.1 mm Implant Bur, 7 mm 06-7IB<br />
4.1 mm Implant Bur, 9 mm 06-9IB<br />
4.1 mm Implant Bur, 12 mm 06-12IB<br />
5.0 mm Implant Bur, 5 mm 06W-5IB<br />
5.0 mm Implant Bur, 7 mm 06W-7IB<br />
5.0 mm Implant Bur, 9 mm 06W-9IB<br />
5.0 mm Implant Bur, 12 mm 06W-12IB<br />
Drill Extension<br />
06-DE<br />
3.5 mm Trial Fit Gage, 9 mm 06M-9TFG/O<br />
4.1 mm Trial Fit Gage, 7 mm 06-7TFG/O<br />
4.1 mm Trial Fit Gage, 9 mm 06-9TFG/O<br />
4.1 mm Trial Fit Gage, 12 mm 06-12TFG/O<br />
5.0 mm Trial Fit Gage, 5 mm 06W-5TFG/O<br />
5.0 mm Trial Fit Gage, 7 mm 06W-7TFG/O<br />
5.0 mm Trial Fit Gage, 9 mm 06W-9TFG/O<br />
5.0 mm Trial Fit Gage, 12 mm 06W-12TFG/O<br />
Paralleling Pins, Pack of 4<br />
06-PP<br />
Mallet<br />
06-M/L<br />
Punch Handle, straight 06-H<br />
Punch Handle, offset<br />
06-HOS<br />
Stainless Steel Punch Tip<br />
06-PTM<br />
Tip Wrench<br />
06-TW<br />
Hex Driver 0.05“ – short<br />
06-HDS<br />
Radiographic Overlays, 2 Pack<br />
06-RO<br />
Surgical Video on DVD<br />
Item No.<br />
06-SV<br />
<strong>Endopore</strong> Surgical Kits<br />
for use <strong>with</strong> all <strong>Endopore</strong> <strong>Implants</strong> <strong>with</strong> internal connection,<br />
internal <strong>hex</strong> and <strong>external</strong> <strong>hex</strong>.<br />
<strong>Endopore</strong> Osteotome Kit<br />
<strong>Endopore</strong> Osteotome Kit<br />
Osteotome Instrument Tray, fully equipped<br />
Content of a full equipped tray<br />
Osteotome Tip #1<br />
Osteotome Tip #2<br />
Osteotome Tip #3<br />
Stainless Steel Punch Tip<br />
Punch Handle, straight, Pack of 4<br />
Punch Handle, offset, one<br />
Mallet<br />
Osteotome Instrument Tray, empty<br />
Item No.<br />
06-OTKIT<br />
06-OT1<br />
06-OT2<br />
06-OT3<br />
06-PTM<br />
06-H<br />
06-HOS<br />
06-M/L<br />
06-ITM/S2<br />
Surgical Instrument Tray, empty<br />
06-ITM/S1
Surgery<br />
BICORTICAL ENDOPORE® ®<br />
39<br />
<strong>Endopore</strong> Surgical Instrumentation<br />
Burs and Drills<br />
Crestotom<br />
for the removal of soft tissue, for smoothing<br />
and levelling of the alveor crest<br />
Initial Perforation (IP) Drill<br />
for initial perforation of the compact cortical<br />
bone, Ø 2.00<br />
Item No.<br />
1452<br />
90024<br />
Round Bur<br />
Ø 2.3 mm<br />
06-RB<br />
Twist Drill<br />
short, Ø 2.5 mm, total length 30 mm<br />
long, Ø 2.5 mm, total length 39 mm<br />
06-2.5TDS<br />
06-2.5TDL<br />
Implant Burs Length Item No.<br />
Implant Burs<br />
for implant Ø 3.5 mm<br />
9 mm 06M-9IB<br />
for implant Ø 4.1 mm<br />
7 mm 06-7IB<br />
9 mm 06-9IB<br />
12 mm 06-12IB<br />
for implant Ø 5.0 mm<br />
5 mm 06W-5IB<br />
7 mm 06W-7IB<br />
9 mm 06W-9IB<br />
12 mm 06W-12IB
ENDOPORE ®<br />
Surgery<br />
Drill Extension<br />
Drill Extension<br />
Item No.<br />
06-DE<br />
Trial Fit Gages/Osteotome Final Tips Length Item No.<br />
Trial Fit Gages/Osteotome Final Tips<br />
Implant Ø 3.5 mm<br />
9 mm 06M-9TFG/O<br />
Implant Ø 4.1 mm<br />
7 mm 06-7TFG/O<br />
9 mm 06-9TFG/O<br />
12 mm 06-12TFG/O<br />
40<br />
Implant Ø 5.0 mm<br />
The trial fit gages are threaded to connect<br />
to the punch handles. The trial fit gage corresponding<br />
to the size of the implant to be<br />
placed, acts as the final osteotome tip.<br />
5 mm 06W-5TFG/O<br />
7 mm 06W-7TFG/O<br />
9 mm 06W-9TFG/O<br />
12 mm 06W-12TFG/O<br />
Paralleling Pin<br />
Item No.<br />
Paralleling Pin<br />
for use <strong>with</strong> 2.5 mm twist drill<br />
06-PP<br />
Mallet and Punch Handles<br />
Item No.<br />
Mallet<br />
06-M/L<br />
Punch Handles<br />
for use in conjunction <strong>with</strong> osteotome tips and<br />
trial fit gages for osteotome technique<br />
straight<br />
offset<br />
06-H<br />
06-HOS<br />
straight<br />
offset
Surgery<br />
BICORTICAL ENDOPORE® ®<br />
41<br />
Punch Tips<br />
Stainless Steel Punch Tip for implant<br />
placement<br />
For use <strong>with</strong> all diameters. Connects to punch<br />
handle.<br />
Item No.<br />
06-PTM<br />
Osteotome Punch Tips<br />
Osteotome punch tips connect to the punch<br />
handles.<br />
Osteotome Tip #1<br />
Osteotome Tip #2<br />
Osteotome Tip #3<br />
06-OT1<br />
06-OT2<br />
06-OT3<br />
Tip #1 Tip #2 Tip #3<br />
Wrench and Driver<br />
Tip Wrench<br />
The tip wrench is used for tightening or<br />
loosening trial fit gages, punch tip and<br />
osteotome tips to the punch handles.<br />
Item No.<br />
06-TW<br />
Hex Driver 0.05” – short<br />
length 13 mm<br />
06-HDS<br />
13 mm<br />
Cover Screw Trephines<br />
Item No.<br />
Cover Screw Trephines<br />
for implant Ø 3.5 mm<br />
for implant Ø 4.1 mm<br />
for implant Ø 5.0 mm<br />
Tissue Punch<br />
Tissue Punch<br />
The metal tissue punch attaches to the drill<br />
handpiece and will cleanly section a 4.3 mm<br />
diameter flap of tissue over the implant.<br />
06M-3.5TR/CS<br />
06-4.1TR/CS<br />
06W-5.0TR/CS<br />
Item No.<br />
06-TP
ENDOPORE ®<br />
Articles in alphabetic order<br />
Articles in alphabetic order<br />
Item<br />
Page<br />
Item<br />
Page<br />
42<br />
Angled Abutments for<br />
- External Hex 30<br />
- Internal Hex 16<br />
Cementable Abutments for Internal Connection 7<br />
Cover Screw for<br />
- Internal connection 7<br />
- Internal Hex 14<br />
- External Hex 26<br />
Cover Screw Trephines 41<br />
Crestotom 39<br />
Dalla Bona Abutment System for<br />
- Internal Connection 10<br />
- Internal Hex 19<br />
- External Hex 33<br />
Drill Extension 40<br />
Driver Extension 36<br />
Driver Housing 8/10/36<br />
Driver Tips 36<br />
ECO Abutment System 7<br />
Guide Pin 37<br />
Healing Abutments for<br />
- Internal Hex 14<br />
- External Hex 26<br />
Hex Driver 36/41<br />
Hex Tip 0.05" 8/36<br />
Hex Tip 0.05", short 36<br />
Hex Abutments for<br />
- Internal Hex 16<br />
- External Hex 29/30<br />
Implant Analogs for<br />
- Internal Hex 15<br />
- External Hex 28<br />
Implant Burs 39<br />
<strong>Implants</strong> <strong>with</strong><br />
- Internal Connection 4<br />
- Internal Hex 11<br />
- External Hex 22<br />
Initial Perforation (IP) Drill 39<br />
Insertion Tip 8<br />
Latch Driver 37<br />
Lapping Tool <strong>with</strong> guide pin 37<br />
Locator Abutments for<br />
- Internal Connection 9<br />
- Internal Hex 18<br />
- External Hex 32<br />
Mallet 40<br />
Octabutment System 8<br />
O-Ring Abutment System (ORS) for<br />
- Internal Connection 10<br />
- Internal Hex 19<br />
- External Hex 32<br />
Osteotome Instrument Tray, fully equipped 38<br />
Paralleling Pin 40<br />
Punch Handles 40<br />
Punch Tips 41<br />
Reamer 37<br />
Retaining Screws 15/28<br />
Round Bur 39<br />
Surgical Instrument Tray, fully equipped 38<br />
Temporary Titanium Abutments 30<br />
Tip Wrench 41<br />
Tissue Punch 41<br />
Torque Wrench 20 Ncm Ratchet 9/18/36<br />
Torque Wrench 30 Ncm Ratchet 36<br />
Transfer Copings for<br />
- Internal Hex 15<br />
- External Hex 27<br />
Trial Fit Gages/Osteotome Final Tips 40<br />
Twist Drills 39<br />
UCLA-Abutments for<br />
- Internal Hex 17<br />
- External Hex 31<br />
UMA O-Ring Abutment System for External Hex 35<br />
UMA System for<br />
- Internal Hex 20<br />
- External Hex 34<br />
UMA Abutment Driver 36<br />
UMA Friction Grip Driver 37<br />
Waxing Sleeve 37
ENDOPORE ® Implant<br />
Internal<br />
Connection<br />
Internal Hex<br />
Osteotome PROCEDURES<br />
peRfect<br />
External Hex<br />
INTERNAL HEX<br />
PerfeCT SURFACE<br />
EXTERNAL HEX<br />
NTERNAL<br />
PERFECT SURFACE<br />
Implant Placement Procedure<br />
Sybron Implant Solutions<br />
A World of Implant Solutions<br />
The dental implant platform of Sybron Dental Specialties (SDS)<br />
brings together three organizations that have been leaders<br />
in implant manufacturing, design and development since the<br />
inception of implant dentistry.<br />
Delivering two of the most respected, leading-edge dental<br />
implants on the market – ENDOPORE ® and PITT-EASY ® – we<br />
are giving you access to a world of implant solutions.<br />
Manufacturer:<br />
Sybron Implant Solutions<br />
1717 West Collins Avenue<br />
Orange, California 92867 · United States<br />
www.sybronimplants.com<br />
Distributed by:<br />
Sybron Implant Solutions GmbH<br />
Julius-Bamberger-Straße 8a · 28279 Bremen · Germany<br />
Phone +49 421 43939-0 · Fax +49 421 443936<br />
www.sybronimplants.de · info@sybronimplants.de<br />
07-0189: 06/07