LED light engine / OLED LED compact Umodule STARK ... - Tridonic

D
LED light engine / OLED
LED compact
Product description
• Ideal for ceiling-mounted and wallmounted luminaires
• Efficiency of the module up to 125 lm/W
• High colour rendering index CRI > 80
• Small colour tolerance MacAdam 4 4
• Small luminous flux tolerances
• Colour temperatures 3,000 and 4,000 K
• Self-cooling (no additional heat sink required)
• Push terminals for quick and simple wiring
• Simple installation (e.g. screws)
• Long life-time: 50,000 hours
• 5-year guarantee
Technical data
Beam characteristic 120°
Ambient temperature ta -30 ... +50 °C
Typ. tp point 65 °C
Risk group (EN 62471:2008) 0
Type of protection
IP00
È
Standards, page 2
For colour temperatures and tolerances, page 5
Umodule STARK CLE 160-2200 CLASSIC
STARK CLE
92
33,25
33,25
92
Ø4,5
Ø11
tp
Ø164,5
Ordering data
Type
Article number
Colour Packaging, Weight
temperature carton per pc.
STARK-CLE-160-2200-830-CLA 89601846 3,000 K 50 pc(s). 0.074 kg
STARK-CLE-160-2200-840-CLA 89601847 4,000 K 50 pc(s). 0.074 kg
Specific technical data
Type
Photometric Typ. luminous Typ. luminous Typ. forward Typ. forward Typ. power Luminous Luminous Luminous Colour rendering Energy
code flux at flux at current 123 voltage consumption 1 efficacy module efficacy module efficacy system index CRI classification
tp 25 °C 1 tp 65 °C 1
at tp 25 °C at tp 65 °C at tp 65 °C
Operating mode at 350 mA
STARK-CLE-160-2200-830-CLA 830/4xx 2,130 lm 2,050 lm 350 mA 51.4 V 18 W 118 lm/W 114 lm/W 97 lm/W > 80 A+
STARK-CLE-160-2200-840-CLA 840/4xx 2,280 lm 2,190 lm 350 mA 51.4 V 18 W 127 lm/W 122 lm/W 104 lm/W > 80 A+
1 Tolerance range for optical and electrical data: ±10 %.
2 Max. permissible repetitive peak current: 480 mA.
3 Max. permissible surge current: 0.54 A, duration max. 10 ms.
4 Integrated measurement over the whole module.
PHASED OUT
79,25
158,5
Data sheet 07/14-LED150-2
Subject to change without notice.
www.tridonic.com 1

LED light engine / OLED
LED compact
Standards
EN 62031
EN 62471
IEC 61000-4-2
Photometric code
Key for photometric code, e. g. 830 / 449
1 st digit 2 nd + 3 rd digit 4 th digit 5 th digit 6 th digit
Lumen maintanance after 25%
Code CRI
McAdams after of the life-time (max.6000h)
Colour temperature in McAdams 25% of the Code Remaining lumen
7 67 – 76 Kelvin x 100 initial life-time (max. 7 ≥ 70 %
8 77 – 86 6,000h) 8 ≥ 80 %
9 87 – ≥90 9 ≥ 90 %
Thermal design and heat sink
The rated life of u products depends to a large extent on the temperature. If
the permissible temperature limits are exceeded, the life of the
umodule STARK CLE will be greatly reduced or the umodule STARK CLE
may be destroyed.
tp point, ambient temperature and life-time
The temperature at tp reference point is crucial for the light output and life-time
of a u product.
For umodule STARK CLE a tp temperature of 65 °C has to be complied in order
to achieve an optimum between light output and life-time.
Compliance with the maximum permissible reference temperature at the tp point
must be checked under operating conditions in a thermally stable state. The
maximum value must be determined under worst-case conditions for the relevant
application.
The tc and tp temperature of LED modules from Tridonic are measured at the same
reference point.
Mounting instruction
None of the components of the umodule STARK CLE (substrate, LED,
electronic components etc.) may be exposed to tensile or compressive
stresses.
Max. torque for fixing: 0.5 Nm.
The LED modules are mounted with 4 screws per module.
In order not to damage the modules only rounded head screws and an
additional plastic flat washer should be used.
PHASED OUT
EOS/ESD safety guidelines
The device / module contains components that are sensitive to electrostatic
discharge and may only be installed in the factory and on site if
appropriate EOS/ESD protection measures have been taken. No special
measures need be taken for devices/modules with enclosed casings
(contact with the pc board not possible), just normal installation practice.
Please note the requirements set out in the document EOS / ESD
guidelines (Guideline_EOS_ESD.pdf) at:
http://www.tridonic.com/esd-protection
Data sheet 07/14-LED150-2
Subject to change without notice.
www.tridonic.com 2

LED light engine / OLED
LED compact
Thermal behaviour
storage temperature -30... +80 °C
operating temperature ta -30 ... +50 °C
tp (at typ. current) 65 °C
tc max. (at typ. current) 75 °C
max. humidity* 0 ... 70 %
* not condensed
Lumen maintenance
tp temperature in °C forward current in mA luminous flux in % operating time in h
65 350 70 > 45,000
Electrical supply/choice of LED control gear
umodule STARK CLE from Tridonic are not protected against overvoltages,
overcurrents, overloads or short-circuit currents. Safe and reliable operation
can only be guaranteed in conjunction with a LED control gear which complies with
the relevant standards. The use of uconverter from Tridonic in combination
with umodule STARK CLE guarantees the necessary protection for safe and
reliable operation.
Wiring
umodule STARK LLE are basic isolated up to 190 V against ground
and can be mounted directly on earthed metal parts of the luminaire.
If the max. output voltage of the led control gear (also against earth) is
above 190 V, an additional isolation between LED module and heat sink is
required (for example by isolated thermal pads) or by a suitable luminaire
construction.
At voltages > 60 V an additional protection against direct touch (test
finger) to the light emitting side of the module has to be guaranteed. This
is typically achieved by means of a non removable light distributor over the
module.
Wiring type and cross section
The wiring can be solid cable with a cross section of
0.4 to 0.75 mm². For the push-wire connection you
have to strip the insulation (6–7 mm).
Loosen wire through twisting and pulling.
wire preparation:
0.4 – 0.75 mm²
+ –
6 – 7 mm
Release of the wiring
Press down the “push button” and remove the cable from front.
Wiring example
230 – 240 V AC
50/60 Hz
L
N
PE
Umodule
STARK CLE 160
+ LED
– LED
Uconverter
LCI ... TEC C
N
L
SEC
PRI
+
–
If a LED control gear other than Tridonic uconverter is used, it must provide the
following protection:
• Short-circuit protection
• Overload protection
• Overtemperature protection
umodule STARK CLE must be supplied by a constant current LED
control gear.
Operation with a constant voltage LED control gear will lead to an irreversible
damage of the module.
Wrong polarity can damage the umodule STARK CLE.
PHASED OUT
Data sheet 07/14-LED150-2
Subject to change without notice.
www.tridonic.com 3

LED light engine / OLED
LED compact
Relative luminous flux
Forward current vs. forward voltage
rel. luminous flux [%]
Relative luminous flux vs. operating current
rel. luminous flux [%]
The diagrams based on statistic values.
The real values can be different.
Optical characteristics Umodule STARK CLE
The optical design of the umodule STARK CLE product line ensures optimum
homogenity for the light distribution.
Light distribution
relative intensity Iv/Iv, max
110
100
90
80
70
25 35 45 55 65 75 85
tp [°C]
1,4
1,2
1,0
0,8
0,6
0,4
0,2
200
100
80
60 -60°
40
-50°
250 300 350 400 450 500
Operating current [mA]
-40°
-30°
-20°
-10°
0°
20
80°
10°
20°
30°
40°
50°
60°
70°
Forward current [mA]
480
440
400
360
320
280
240
200
160
120
80
40
0
40,8 42,5 44,2 45,9 47,6 49,3 51,0 52,7 54,4
Forward voltage [V]
The colour temperature is measured integral over the complete module.
The single LED light points can have deviations in the colour coordinates
within MacAdam tbd.
To ensure an ideal mixture of colours and a homogenious light distribution
a suitable optic (e. g. PMMA diffuser) and a sufficient spacing between
module and optic (typ. 5 cm) should be used.
PHASED OUT
0
-100
-80
-60
-40
-20 0 20 40
60
80 100
90°
3D-Data, photometric data and Design-in guide available on request or go to www.
tridonic.com
Data sheet 07/14-LED150-2
Subject to change without notice.
www.tridonic.com 4

LED light engine / OLED
LED compact
Coordinates and tolerances according to CIE 1931
The specified colour coordinates are measured integral by a current impulse with typical values of module and a duration of 200 ms.
The ambient temperature of the measurement is ta = 25 °C.
The measurement tolerance of the colour coordinates are ± 0.01.
3,000 K
x0
y0
Centre 0.4344 0.4032
0,4250
0,4200
0,4150
0,4100
0,4050
0,4000
0,3950
0,3900
0,3850
4,000 K
x0
y0
Centre 0.3828 0.3803
0,4000
0,3950
0,3900
0,3850
0,3800
0,3750
0,3700
0,3650
0,3600
0,4150
0,3600
0,4200
MacAdam Ellipse: 4SDCM
0,3650
0,4250
0,3700
0,4300
0,3750
0,4350
0,3800
0,4400
0,3850
MacAdam Ellipse: 4SDCM
0,4450
0,3900
0,4500
0,3950
0,4550
0,4000
norm. intensity [%]
norm. intensity [%]
0,07
0,06
0,05
0,04
0,03
0,02
0,01
0,00
380 420 460 500 540 580 620 660 700 740 780
wave length [nm]
0,07
0,06
0,05
0,04
0,03
0,02
0,01
0,00
380 420 460 500 540 580 620 660 700 740 780
wave length [nm]
PHASED OUT
Data sheet 07/14-LED150-2
Subject to change without notice.
www.tridonic.com 5