O&O DiskImage 7 User's Guide - O&O Software
O&O DiskImage 7 User's Guide - O&O Software O&O DiskImage 7 User's Guide - O&O Software
Machine independent restoration (M.I.R.) Manual adaptation Enable automatic adaptation on changed hardware (M.I.R.) You can make manual adaptation to the changed hardware following restoration orcloning. • To do this, run a restoration or cloning of the system partition or the entire computer. • After successful restoration, please open the O&O DiskImage dialog to change the computer properties Tools/Change computer identity. O&O DiskImage-43
Machine independent restoration (M.I.R.) Change computer identity manually The adaptations made by M.I.R can be divided into three activities which can be enabled/disabled when selecting Restoration on different hardware (machine independent restoration). Exchange hardware abstraction layer (HAL) Windows operating systems must be compatible with a variety of hardware platforms. This portability is achieved through a special layer within the operating system that is responsible for the management and control of hardware, architecture and machine-dependent devices, such as the I/O interfaces, Interrupt Controller and multi processor communication mechanisms. This layer is commonly installed on and aligned to the current hardware on an installed and running Windows. If the hardware is exchanged, it becomes necessary to align the layer accordingly in order to ensure smooth and continued functionality of the operating system and the programs installed. Apply currently loaded drivers of the device control Drivers are an interface between the I/O-Manager and the corresponding hardware. They are not accessed directly, but over the hardware abstraction layer. After replacement, the corresponding driver of new hardware has got to be installed in order to make sure it can work properly with this layer. Enable the installation program of the operating system after restarting O&O DiskImage-44
- Page 2 and 3: Copyrights Text, illustrations and
- Page 4 and 5: Compress image 8 Encryption 9 Exclu
- Page 6 and 7: Exclude data from compression 33 Lo
- Page 8 and 9: Merge images 69 Handling virtual ha
- Page 10 and 11: About O&O DiskImage 7 About O&O Dis
- Page 12 and 13: About O&O DiskImage 7 Image file An
- Page 14 and 15: System requirements System requirem
- Page 16 and 17: Features at a glance Mount files fr
- Page 18 and 19: Features at a glance Encryption You
- Page 20 and 21: Features at a glance Adapt size of
- Page 22 and 23: Features at a glance User Interface
- Page 24 and 25: Installation and registration Onlin
- Page 26 and 27: Installation and registration Just
- Page 28 and 29: Quick Start • For the simplified
- Page 30 and 31: Quick Start Note: If there is not e
- Page 32 and 33: Quick Start Add job Folder view: So
- Page 34 and 35: Quick Start Drive restoration Enabl
- Page 36 and 37: Quick Start 1. Please make sure tha
- Page 38 and 39: Quick Start Select Clone driving Se
- Page 40 and 41: Settings for drive imaging Image of
- Page 42 and 43: Settings for drive imaging Exclude
- Page 44 and 45: Settings for drive imaging Ignore b
- Page 46 and 47: File backup options When creating a
- Page 48 and 49: Settings for the restoration of dri
- Page 50 and 51: Machine independent restoration (M.
- Page 54 and 55: Machine independent restoration (M.
- Page 56 and 57: Settings for Cloning drives 1. To l
- Page 58 and 59: Start directly from bootable disk S
- Page 60 and 61: Start directly from bootable disk 2
- Page 62 and 63: Scheduling functions Scheduling fun
- Page 64 and 65: Scheduling functions Scheduling job
- Page 66 and 67: Scheduling functions Job Assistant:
- Page 68 and 69: Scheduling functions Run commands b
- Page 70 and 71: Scheduling functions Mark the job s
- Page 72 and 73: Tools Image information O&O DiskIma
- Page 74 and 75: Create bootable media Burn Wizard W
- Page 76 and 77: Create bootable media Mount image f
- Page 78 and 79: Create bootable media Unmount drive
- Page 80 and 81: Create bootable media Combine incre
- Page 82 and 83: Create bootable media Map network d
- Page 84 and 85: Program settings Program settings Y
- Page 86 and 87: Program settings Reset security con
- Page 88 and 89: Program settings 7. You can also ad
- Page 90 and 91: Program settings Under Behavior you
- Page 92 and 93: Program settings Context menu of th
- Page 94 and 95: View 3. Read image information - di
- Page 96 and 97: Frequently asked questions • merg
- Page 98 and 99: Frequently asked questions Call the
- Page 100 and 101: Frequently asked questions Name of
Machine independent restoration (M.I.R.)<br />
Manual adaptation<br />
Enable automatic adaptation on changed hardware (M.I.R.)<br />
You can make manual adaptation to the changed hardware following restoration orcloning.<br />
• To do this, run a restoration or cloning of the system partition or the entire computer.<br />
• After successful restoration, please open the O&O <strong>DiskImage</strong> dialog to change the computer properties<br />
Tools/Change computer identity.<br />
O&O <strong>DiskImage</strong>-43