Lexicon 480L | PDF - Freeverb3
Lexicon 480L | PDF - Freeverb3 Lexicon 480L | PDF - Freeverb3
5 Bank 6: the Twin Delays Programs This chapter describes the Twin Delays programs located in Bank 6.
Lexicon 480L Owner's Manual Page One DRY L Ch Dry Level DRY R Ch Dry Level ROL L DLY1 Rolloff ROL R DLY1 Rolloff PAN L Channel Pan PAN R Channel Pan Page Two DL1 L DLY1 Value LV1 L DLY1 Level FB1 L DLY1 Feedback DL2 R DLY2 Value LV2 R DLY 2 Level FB2 R DLY2 Feedback Page Three DL3 L DLY3 Value LV3 L DLY3 Level FB3 L DLY3 Feedback DL4 R DLY4 Value LV4 R DLY4 Level FB4 R DLY4 Feedback Page Four FIN L Fine Delay FIN R Fine Delay MST Delay Multiplier The Twin Delays Program The Twin Delays program located in Bank 6 is a four voice delay line with independently-adjustable level, feedback, and delay time for each voice. Feedback can be positive or negative. Feedback for Delays 3 and 4 is cross-panned. Independent low pass filters, adjustable between 120Hz and full bandwidth, are provided for the first and second delay voices (Delay 1 Left Channel and Delay 2 Right Channel)and their respective feedback paths. These voices also have independent panning controls. About the Twin Delays Parameters Page One DRY (L and R Channel Dry Level) L DRY sets the dry signal level from the left input to the left output. It is not affected by L or R PAN. R DRY sets the dry signal level from the right input to the right output. It is not affected by L or R PAN. ROL (Rolloff) Rolloff is a low pass filter that can be adjusted independently for LDLY1 and RDLY2 voices. Values for Rolloff are adjustable between 120Hz and full range. Page Two DL1 (LDLY1 Val) Sets the delay time for the first (left channel) delay voice. LV1 (LDLY1 Lvl) Adjusts the level (amplitude) of DL1. FB1 (LDL1 Fbk) Adjusts the amount of feedback (positive or negative) around DL1. DL2 (RDLY2 Val) Sets the delay time for the second (right channel) delay voice. LV2 (RDLY2 Lvl) Adjusts the level (amplitude) of level for DL2. FB2 (RDL2 Fbk) Adjusts the amount of feedback (positive or negative) around DL2. L PAN (Left Channel Pan) L PAN sets the panning of the DL1 and FB1 signal to the left and right outputs. R PAN (Right Channel Pan) R PAN sets the panning of the DL2 and FB2 signal to the left and right outputs. 5-2
- Page 7 and 8: 1 Installation and Audio Connection
- Page 9 and 10: Installation and Audio Connections
- Page 11 and 12: Installation and Audio Connections
- Page 13 and 14: Installation and Audio Connections
- Page 15 and 16: Installation and Audio Connections
- Page 17 and 18: Installation and Audio Connections
- Page 19 and 20: 2 Basic Operation This chapter desc
- Page 21 and 22: Basic Operation Operating Modes The
- Page 23 and 24: Basic Operation Checking Your Syste
- Page 25 and 26: Basic Operation Using Two LARCs to
- Page 27 and 28: Basic Operation Level Calibration A
- Page 29 and 30: Basic Operation Setting Analog Inpu
- Page 31 and 32: Basic Operation Using Digital Signa
- Page 33 and 34: Basic Operation Storing and Naming
- Page 35 and 36: Basic Operation MIDI SysEx Program
- Page 37 and 38: Basic Operation A dumped register b
- Page 39 and 40: Lexicon 480L Owner's Manual Before
- Page 41 and 42: Lexicon 480L Owner's Manual Page On
- Page 43 and 44: Lexicon 480L Owner's Manual Page Tw
- Page 45 and 46: Lexicon 480L Owner's Manual Program
- Page 47 and 48: Lexicon 480L Owner's Manual Program
- Page 49 and 50: Lexicon 480L Owner's Manual Program
- Page 51 and 52: Lexicon 480L Owner's Manual Program
- Page 53 and 54: Lexicon 480L Owner's Manual Page On
- Page 55 and 56: Lexicon 480L Owner's Manual WANDER
- Page 57: Lexicon 480L Owner's Manual Program
- Page 61 and 62: Lexicon 480L Owner's Manual Program
- Page 63 and 64: Lexicon 480L Owner's Manual Introdu
- Page 65 and 66: Lexicon 480L Owner's Manual How to
- Page 67 and 68: Lexicon 480L Owner's Manual Time Va
- Page 69 and 70: Lexicon 480L Owner's Manual Stereo
- Page 71 and 72: Lexicon 480L Owner's Manual HEAD TR
- Page 73 and 74: 7 Bank 8: the Pitch Change and Dopp
- Page 75 and 76: Bank 8: the Pitch Change and Dopple
- Page 77 and 78: Bank 8: the Pitch Change and Dopple
- Page 79 and 80: 8 Bank 9: the Mastering Programs Th
- Page 81 and 82: Bank 9: the Mastering Programs If s
- Page 83 and 84: Bank 9: the Mastering Programs Page
- Page 85 and 86: Bank 9: the Mastering Programs Page
- Page 87 and 88: Bank 9: the Mastering Programs Page
- Page 89 and 90: Bank 9: the Mastering Programs LFB
- Page 91 and 92: 9 Bank 10: the Compressor Programs
- Page 93 and 94: Bank 10: the Compressor Programs AT
- Page 95 and 96: 10 Banks 11-12: the Random Halls an
- Page 97 and 98: Banks 11-12: the Random Halls and S
- Page 99 and 100: Banks 11-12: the Random Halls and S
- Page 101 and 102: Banks 11-12: the Random Halls and S
- Page 103 and 104: 11 Banks 13-14: the Ambience Progra
- Page 105 and 106: Banks 13-14: the Ambience Programs
- Page 107 and 108: Banks 13-14: the Ambience Programs
<strong>Lexicon</strong> <strong>480L</strong> Owner's Manual<br />
Page One<br />
DRY<br />
L Ch Dry Level<br />
DRY<br />
R Ch Dry Level<br />
ROL<br />
L DLY1 Rolloff<br />
ROL<br />
R DLY1 Rolloff<br />
PAN<br />
L Channel Pan<br />
PAN<br />
R Channel Pan<br />
Page Two<br />
DL1<br />
L DLY1 Value<br />
LV1<br />
L DLY1 Level<br />
FB1<br />
L DLY1 Feedback<br />
DL2<br />
R DLY2 Value<br />
LV2<br />
R DLY 2 Level<br />
FB2<br />
R DLY2 Feedback<br />
Page Three<br />
DL3<br />
L DLY3 Value<br />
LV3<br />
L DLY3 Level<br />
FB3<br />
L DLY3 Feedback<br />
DL4<br />
R DLY4 Value<br />
LV4<br />
R DLY4 Level<br />
FB4<br />
R DLY4 Feedback<br />
Page Four<br />
FIN<br />
L Fine Delay<br />
FIN<br />
R Fine Delay<br />
MST<br />
Delay Multiplier<br />
The Twin Delays Program<br />
The Twin Delays program located in Bank 6 is a four<br />
voice delay line with independently-adjustable level,<br />
feedback, and delay time for each voice. Feedback can<br />
be positive or negative. Feedback for Delays 3 and 4 is<br />
cross-panned.<br />
Independent low pass filters, adjustable between<br />
120Hz and full bandwidth, are provided for the first and<br />
second delay voices (Delay 1 Left Channel and Delay<br />
2 Right Channel)and their respective feedback paths.<br />
These voices also have independent panning controls.<br />
About the Twin Delays Parameters<br />
Page One<br />
DRY (L and R Channel Dry Level)<br />
L DRY sets the dry signal level from the left input to the<br />
left output. It is not affected by L or R PAN. R DRY sets<br />
the dry signal level from the right input to the right<br />
output. It is not affected by L or R PAN.<br />
ROL (Rolloff)<br />
Rolloff is a low pass filter that can be adjusted independently<br />
for LDLY1 and RDLY2 voices. Values for Rolloff<br />
are adjustable between 120Hz and full range.<br />
Page Two<br />
DL1 (LDLY1 Val)<br />
Sets the delay time for the first (left channel) delay<br />
voice.<br />
LV1 (LDLY1 Lvl)<br />
Adjusts the level (amplitude) of DL1.<br />
FB1 (LDL1 Fbk)<br />
Adjusts the amount of feedback (positive or negative)<br />
around DL1.<br />
DL2 (RDLY2 Val)<br />
Sets the delay time for the second (right channel) delay<br />
voice.<br />
LV2 (RDLY2 Lvl)<br />
Adjusts the level (amplitude) of level for DL2.<br />
FB2 (RDL2 Fbk)<br />
Adjusts the amount of feedback (positive or negative)<br />
around DL2.<br />
L PAN (Left Channel Pan)<br />
L PAN sets the panning of the DL1 and FB1 signal to<br />
the left and right outputs.<br />
R PAN (Right Channel Pan)<br />
R PAN sets the panning of the DL2 and FB2 signal to<br />
the left and right outputs.<br />
5-2