Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
For Models: JGH:E:K:T Section 4 Part Replacement<br />
“BTUU” Single Acting Seal Set<br />
This four-ring set seals in one direction only. The<br />
first ring (pressure side) is radially cut; the second<br />
is tangentially step cut. These rings are<br />
doweled to stagger the cuts from one ring to the<br />
other. The third and forth rings are solid and<br />
have bores larger than the rod diameter, allowing<br />
the radial joints of the sealing rings to form a<br />
tight gas seal. Total end gap installed is 3/8 to<br />
13/32 in. (9.5 to 10.3 mm) for PEEK, and 3/16 to<br />
7/32 in. (4.8 to 5.6 mm) for Teflon. Maintain end<br />
gap by adjusting ring gap or replacing the ring.<br />
“CU” Single Acting Seal Set<br />
This three-ring set seals in one direction only.<br />
The first ring (pressure side) is radially cut. The<br />
second ring is tangentially cut. The first two rings<br />
are doweled to stagger the cuts from one ring to<br />
the other. The third ring is called a back-up ring. It<br />
is solid and has a bore larger than the rod diameter.<br />
Total end gap installed is 3/8 to 13/32 in. (9.5<br />
to 10.3 mm) for PEEK, Bronze, and Cast Iron,<br />
and 3/16 to 7/32 in. (4.8 to 5.6 mm) for Teflon.<br />
Maintain end gap by adjusting ring gap or replacing<br />
the ring.<br />
“STU” Single Acting Seal Set<br />
This three-ring set seals in one direction only.<br />
The first ring (pressure side) is solid, with radial<br />
groves on the pressure side. The second ring is<br />
tangentially cut. The third ring is solid.<br />
“CR” Single Acting Seal Set<br />
This three-ring set seals in one direction only.<br />
The first ring (pressure side) is radially cut. The<br />
second ring is tangentially cut. The first two rings<br />
are doweled to stagger the cuts from one ring to<br />
the other. The third ring is called a back-up ring. It<br />
is radially cut and has a bore larger than the rod<br />
diameter to allow the radial joints to form a tight<br />
gas seal. Total end gap installed is 3/8 to 13/32<br />
in. (9.5 to 10.3 mm) for PEEK, Bronze and Cast<br />
Iron, and 3/16 to 7/32 in. (4.8 to 5.6 mm) for Teflon.<br />
Maintain end gap by adjusting ring gap or<br />
replacing the ring.<br />
3/11 PAGE 4-21<br />
B<br />
K<br />
B B<br />
K<br />
K<br />
Pressure<br />
FIGURE 4-23 “BTUU” Single Acting Seal Set<br />
B<br />
B<br />
K<br />
B B<br />
FIGURE 4-24 “CU” Single Acting Seal Set<br />
K<br />
K<br />
K<br />
K<br />
K<br />
Pressure<br />
Pressure<br />
FIGURE 4-25 “STU” Single Acting Seal Set<br />
K<br />
A<br />
B B<br />
FIGURE 4-26 “CR” Single Acting Seal Set<br />
K<br />
K<br />
A A<br />
Pressure