Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Section 4 Part Replacement For Models: JGH:E:K:T<br />
“BD” Double Acting Seal Set<br />
This two-ring set consists of tangentially step cut rings doweled<br />
to stagger the tangential cuts from one ring to the other.<br />
Total end gap installed is 3/8 to 13/32 in. (9.5 to 10.3 mm) for<br />
PEEK, Bronze, and Cast Iron, and 3/16 to 7/32 in. (4.8 to 5.6<br />
mm) for Teflon. Maintain end gap by adjusting ring gap or<br />
replacing the ring. This double acting set seals in either direction.<br />
In cylinders operating near atmospheric pressure, it prevents<br />
air from entering the cylinder. Install with the match mark<br />
letters facing the pressure.<br />
"WAT" Double Acting Seal Set<br />
In this three-ring Teflon set, the first two rings (pressure<br />
side) are radially cut; the third is tangentially step cut.<br />
The last two rings are doweled to stagger the cuts from<br />
one ring to the other. Total end gap installed is 3/16 to<br />
7/32 in. (4.8 to 5.6 mm). Maintain end gap by adjusting<br />
ring gap or replacing the ring. The first ring, along with<br />
the center ring, forms a wedge that overcomes rod friction<br />
and holds the ring set against both groove faces<br />
during either direction of rod travel. Use this ring set primarily<br />
for low pressure applications. WAT rings must be<br />
centered when installed in the packing case.<br />
“AL” Double Acting Seal Set<br />
This five-ring Teflon set functions like a<br />
double-ended “WAT” ring set. Total end<br />
gap installed is 3/16 to 7/32 in. (4.8 to 5.6<br />
mm). Maintain end gap by adjusting ring<br />
gap or replacing the ring. It totally blocks<br />
leakage in a groove supplied with lowpressure<br />
fluid. AL rings must be centered<br />
when installed in the packing case.<br />
“BTU” Single Acting Seal Set<br />
This three-ring set seals in one direction only.<br />
The first ring (pressure side) is radially cut; the<br />
second is tangentially step cut. These first two<br />
rings are doweled to stagger the cuts from one<br />
ring to the other. The third ring is called a back-up<br />
ring. It is solid, with a bore larger than the rod<br />
diameter, allowing radial joints to form a tight gas<br />
seal. Total end gap installed is 3/8 to 13/32 in.<br />
(9.5 to 10.3 mm) for PEEK, Bronze, and Cast<br />
Iron, and 3/16 to 7/32 in. (4.8 to 5.6 mm) for Teflon.<br />
Maintain end gap by adjusting ring gap or<br />
replacing ring.<br />
PAGE 4-20 3/11<br />
M<br />
D<br />
V<br />
U<br />
U<br />
V<br />
V<br />
Pressure<br />
FIGURE 4-19 “BD” Double<br />
Acting Seal Set<br />
A<br />
A<br />
M<br />
D D<br />
FIGURE 4-20 “WAT” Double<br />
Acting Seal Set<br />
A<br />
A<br />
M<br />
A<br />
A A<br />
A<br />
A<br />
U<br />
Pressure<br />
Pressure<br />
FIGURE 4-21 “AL” Double Acting Seal Set<br />
B<br />
K<br />
B B<br />
FIGURE 4-22 “BTU” Single Acting Seal Set<br />
K<br />
K<br />
Pressure