Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Section 2 - Instrumentation For Models: JGH:E:K:T<br />
DNFT Installation<br />
1. Loosen the Allen set screws on the DNFT and remove<br />
magnet housing. Do not remove magnet, spring, or spacer<br />
from magnet housing.<br />
2. Remove piston enclosure plug from end of desired divider<br />
valve. The DNFT installs on any of the divider valves of the<br />
divider block. The DNFT requires the correct magnet<br />
assembly to match the divider valve manufacturer (see<br />
Fig. 2-6).<br />
NOTE: Do not install a DNFT on Lincoln divider valves<br />
with cycle indicator pins.<br />
3. If applicable, verify o-ring or metal gasket is in place on<br />
magnet housing. Thread magnet housing into end of<br />
divider valve. Torque to 15 foot pounds maximum.<br />
4. Slide DNFT all the way onto hex of magnet housing.<br />
Torque Allen set screws on hex of magnet housing to 25<br />
inch pounds, maximum.<br />
5. The LED on the DNFT indicates each divider valve cycle to allow lubricator pump adjustment for<br />
<strong>Ariel</strong> recommended cycle time and oil consumption. If the LED fails to blink during compressor<br />
operation or by manually pumping oil into the divider valve, then the DNFT requires adjustment.<br />
6. The divider valve must cycle during<br />
DNFT adjustment. To cycle it, either<br />
run the compressor or manually pump<br />
oil through the distribution block with a<br />
hand priming pump.<br />
1 2 3 4<br />
5 6 7<br />
8<br />
7. To adjust, slide DNFT all the way onto<br />
hex of magnet housing. Tighten Allen<br />
set screws to 25 inch pounds maxi-<br />
12S<br />
mum. A blinking LED indicates correct<br />
adjustment. If the LED fails to blink<br />
with divider valve cycling, slide DNFT<br />
12T 9<br />
back on the hex of the magnet housing<br />
in 1/16" increments until it does.<br />
10<br />
8. Make all conduit and connections<br />
appropriate for area classification.<br />
Support conduit and fittings to avoid<br />
bending the magnet housing.<br />
9. After DNFT installation and before<br />
compressor start-up, purge all air from<br />
divider block lubrication system with a<br />
purge gun.<br />
1. Divider Valve Piston<br />
2. Magnet<br />
3. Magnet Housing<br />
4. O-Ring<br />
5. Allen Set Screws (2)<br />
SBCO & Trabon O-Ring Seal 7/16”-20<br />
Trabon Metal Gasket Seal 7/16”-20<br />
(1994 or earlier)<br />
Lincoln O-Ring Seal 7/16”-20<br />
Extended Nose<br />
FIGURE 2-6 Typical DNFT Magnet<br />
Assemblies<br />
6. LED<br />
7. Control Housing<br />
8. Wire Leads (7)<br />
9. Divider Valve<br />
10. Piston Enclosure Plug<br />
FIGURE 2-7 Typical DNFT Installation<br />
NOTE: When installing multiple DNFTs, wire each to a separate alarm circuit of the control<br />
panel, annunciator, or PLC to simplify lubrication system and DNFT troubleshooting.<br />
PAGE 2-8 3/11