Heavy Duty Balanced Opposed Compressors - Ariel Corporation

More documents

Recommendations

Info

Section 1 - Tools For Models: JGH:E:K:T j. One 6 lb. dead blow semi-soft faced hammer. k. 3/4” x 36” pry bar. l. 12” long feeler gage set. m. 12” machinist scale with .01” increments. n. 13-piece Allen wrench set, .050 - 3/8”. Recommended Tools Ariel compressor maintenance and repair normally requires only Ariel furnished tools and separately purchased tools and tool kits. However, Ariel also recommends purchasing the additional tools below. Contact Ariel for questions about tools for Ariel units. 1. 12-point box end torque adapter extension wrench set, including 1-1/2 and 2-1/4 inch sizes. 2. Tape Measure. 3. Flashlight. 4. Small Mirror on a Flexible Extension Rod. 5. Small Magnet on a Flexible Extension Rod. 6. Electric and/or Pneumatic Drill 7. Twist Drill Set 8. Torque Multiplier. PAGE 1-4 3/11
For Models: JGH:E:K:T Section 2 - Instrumentation Proflo Lubricator Fluid-Flow Monitor/No-Flow Timer Switch CAUTION: Any arc welding on the skid and/or associated equipment and piping can permanently damage solid-state electronic equipment. Welding can cause immediate failure or reduce electronic equipment life and void the warranty. To protect electronic equipment prior to any arc welding (including repair welding), disconnect all electrical connections including ground, and remove batteries, or completely remove the electronic equipment from the compressor. It is good practice to attach the welding ground clamp as close as possible to the area where the welding will occur and to use the lowest practical welder output setting. Welding must not cause a current flow across any compressor bearing surface, including but not limited to crankshaft and crosshead bearing surfaces. The battery-powered, programmable Proflo is an electronic microprocessor-based switch that senses slow-flow or no-flow conditions in the compressor cylinder force feed lubrication system to facilitate alarm and/or shutdown. It eases force feed lube system operation by accurately monitoring cycle time and system performance. Operators use this information to optimize force feed lube and reduce operating costs. The Proflo monitor works through a magnetic pin that cycles back and forth as the divider valve piston moves. The magnetic pin housing normally threads into the divider valve. The monitor box housing slides onto the pin housing and two hexsocket set screws hold it in place. The liquid crystal display (LCD) indicates: 1. Total operating time of the force feed lube system in hours. 2. "Average", "Last" and "Current" cycle time of the divider valve in seconds. 3. Total divider valve cycles. 4. Remaining battery life in percent. 5. Alarm set time for no-flow indication (programmable from 30 to 240 seconds). 6. Alarm wiring mode: Normally Open or Normally Closed. Proflo electronics come with reverse polarity protection/correction that automatically corrects a reverse polarity output connection on both pulse and alarm outputs. 2 3 4 REFER TO MANUAL FOR PROPER OPERATION & BATTERY TYPE. WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE NON-HAZARDOUS. BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS. FIGURE 2-1 Proflo Electronic Lubricator Fluid Flow Monitor and No-Flow Timer Switch 3/11 PAGE 2-1 5 1 ® 6 1. Hex-Socket Set Screws (2) 2. Magnetic Pin Housing attaches to divider valve 3. Liquid Crystal Display (LCD) 4. Infrared WirelessConnection IrDA Port to download data to a hand-held computer. 5. Set Button. 6. Mode Button.
Page 1: Maintenance and Repair Manual For J
Page 4 and 5: For Models: JGE:H:K:T Oil Strainer.
Page 6 and 7: For Models: JGE:H:K:T SECTION 5 - S
Page 8 and 9: For Models: JGH:E:K:T FIGURE 4-23
Page 10 and 11: For Models: JGH:E:K:T General Safet
Page 12 and 13: For Models: JGH:E:K:T Ariel Contact
Page 14 and 15: Section 1 - Tools For Models: JGH:E
Page 18 and 19: Section 2 - Instrumentation For Mod
Page 32 and 33: Section 3 - Maintenance For Models:
Page 58 and 59: Section 4 Part Replacement For Mode
Page 66 and 67:
Section 4 Part Replacement For Mode
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Section 5 - Start Up For Models: JG
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Section 6 - Troubleshooting For Mod
Page 114 and 115:
Section 6 - Troubleshooting For Mod
Page 116 and 117:
Appendix A Ariel Fasteners and Torq
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Appendix B - Clearances For Models:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Appendix C - Frame Specifications F
Page 130 and 131:
Appendix C - Frame Specifications F
Page 132:
Appendix D Compressor Clearance, Oi
show all

Heavy Duty Balanced Opposed Compressors - Ariel Corporation

Create successful ePaper yourself

Delete template?

Save as template?