Heavy Duty Balanced Opposed Compressors - Ariel Corporation

More documents

Recommendations

Info

Section 5 - Start Up For Models: JGH:E:K:T INITIAL POST START-UP CHECK LIST Description Date Checked Date Verified 8. Check and verify distribution block cycle time indicator and set lubricator pump for proper break-in rate. 9. Check and verify the unit and piping is free from any gas or fluid leaks. Record any occurrences. ________________________________________ ________________________________________ ________________________________________ ________________________________________ 10. Check and verify scrubber high level shutdowns operation and check scrubber dumps operation and frequency. 11. Check, verify, and record tank levels that indicate the amount of liquids removed from the gas. __________________________ 12. Check and verify piston rod packings seal properly in the primary packing vents. 13. Check and verify operation of all safety functions to ensure unit shutdown upon indication. 14. If applicable, check and verify main bearing temperatures and record. Watch for even bearing temperature increase. 15. During various operational conditions, use the Ariel performance program to check and verify operational characteristics of various load steps. Commissioning Agent: __________________ Distributor:___________ Commissioning Agent: __________________ Distributor:___________ Commissioning Agent: __________________ Distributor:___________ Commissioning Agent: __________________ Distributor:___________ Commissioning Agent: __________________ Distributor:___________ Commissioning Agent: __________________ Distributor:___________ Commissioning Agent: __________________ Distributor:___________ Commissioning Agent: __________________ Distributor:___________ PAGE 5-8 3/11
For Models: JGH:E:K:T Section 5 - Start Up 24-HOUR POST START-UP CHECK LIST Description Date Checked Date Verified 1. Record "hot" alignment readings after reaching normal operating temperatures and components become heat soaked. Shutdown and vent gas system. Within 30 minutes and while components are still hot, record dial indicator readings in inches (mm) at the 3, 6, 9 and 12 o’clock positions on lines provided below: Face Rim If using a laser alignment tool, make a print out and attach it to this document. 2. If using a discharge bottle or head end cylinder supports, adjust when components are heat soaked to ensure no excessive forces exist to cause detrimental cylinder deflection. 3. Check and verify torque on gas nozzle flange, valve cap, cylinder head, compressor rod packing flange, and guide to frame bolting. 4. Complete Ariel’s “Compressor Warranty Notification - Installation List Data” (pages 1 and 2). Commissioning Agent: __________________ Commissioning Agent: __________________ Commissioning Agent: __________________ Commissioning Agent: __________________ Distributor:___________ Distributor:___________ Distributor:___________ Distributor:___________ 750-HOUR POST START-UP CHECK LIST Description Date Checked Date Verified 1. Check and verify torque on gas nozzle flange, valve cap, Commissioning Agent: cylinder head, and compressor rod packing flange bolting. __________________ 2. Send completed form and check lists (pages 1-12) to Ariel as noted on page 1. Commissioning Agent: __________________ Distributor:___________ Distributor:___________ 3/11 PAGE 5-9
Page 1:
Maintenance and Repair Manual For J
Page 4 and 5:
For Models: JGE:H:K:T Oil Strainer.
Page 6 and 7:
For Models: JGE:H:K:T SECTION 5 - S
Page 8 and 9:
For Models: JGH:E:K:T FIGURE 4-23
Page 10 and 11:
For Models: JGH:E:K:T General Safet
Page 12 and 13:
For Models: JGH:E:K:T Ariel Contact
Page 14 and 15:
Section 1 - Tools For Models: JGH:E
Page 16 and 17:
Section 1 - Tools For Models: JGH:E
Page 18 and 19:
Section 2 - Instrumentation For Mod
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Section 3 - Maintenance For Models:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59: Section 4 Part Replacement For Mode
Page 102 and 103: Section 5 - Start Up For Models: JG
Page 112 and 113: Section 6 - Troubleshooting For Mod
Page 114 and 115: Section 6 - Troubleshooting For Mod
Page 116 and 117: Appendix A Ariel Fasteners and Torq
Page 122 and 123: Appendix B - Clearances For Models:
Page 128 and 129: Appendix C - Frame Specifications F
Page 130 and 131: Appendix C - Frame Specifications F
Page 132: Appendix D Compressor Clearance, Oi
show all

Heavy Duty Balanced Opposed Compressors - Ariel Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?