Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Heavy Duty Balanced Opposed Compressors - Ariel Corporation Heavy Duty Balanced Opposed Compressors - Ariel Corporation
Section 4 Part Replacement For Models: JGH:E:K:T Before piston rod installation, wipe it with denatured alcohol. Be careful not to leave fingerprints on the rod before it contacts the packing rings. Wipe the rod with denatured alcohol after installation. Clean the head end head or unloader components with denatured alcohol. Use minimal amounts of oil for the bolt-holes to ensure oil does not run into the cylinder. Also install the head end steel gasket without Never-Seez. Disassemble and clean the valves with denatured alcohol, then re-assemble, wipe them again, and install. Clean retainers and high clearance assemblies with denatured alcohol. Use only a thin film of oil for the valve cap O-rings and bolt-holes. Assemble cleaned parts immediately to avoid contamination and corrosion. If cylinder will not commence immediate service, contact Ariel for preservation instructions to ER-34. PAGE 4-44 3/11
For Models: JGH:E:K:T Section 5 - Start Up Warranty Notification - Installation List Data and Start Up Check Lists for JG:A:M:N:P:Q:R:J:H:E:K:T:C:D Reciprocating Compressors The following forms are designed to ensure a successful start-up of smaller Ariel reciprocating compressor models. Ariel warranty coverage requires these completed forms sent to: Administrative Assistant - Sales, Ariel Corporation 35 Blackjack Road • Mount Vernon, Ohio 43050 USA Phone: 740-397-0311 • FAX: 740-397-3856 Warranty Notification - Installation List Data Date:__________________ Name: __________________________________________________ Unassigned Resale Direct Sale Lease-Purchase Rental/Lease Unit Compressor Frame Frame Model:___________________________ Frame Serial #:_________________________________ Frame Lubricant Make and Grade:___________________________________________________________ Package Startup Date:_________________________ Distributor/Fabricator Company:__________________________________ Name:_________________________________ Address:__________________________________________________________________________ City:_______________________ State:_____ Zip:_______________ Country:____________________ Fabricator Unit Number:_______________________________________ Application Air/Nitrogen CNG/GNC FPSO Gathering Fuel Gas Booster Refrigeration Pipeline PRC Injection Storage/Withdrawal Miscellaneous Elevation:_____________________________ H 2 S%:_____________ CO 2 %:_____________ Specific Gravity:_____________ Non-Lube: Yes No 3/11 PAGE 5-1
- Page 50 and 51: Section 3 - Maintenance For Models:
- Page 52 and 53: Section 3 - Maintenance For Models:
- Page 54 and 55: Section 3 - Maintenance For Models:
- Page 56 and 57: Section 3 - Maintenance For Models:
- Page 58 and 59: Section 4 Part Replacement For Mode
- Page 60 and 61: Section 4 Part Replacement For Mode
- Page 62 and 63: Section 4 Part Replacement For Mode
- Page 64 and 65: Section 4 Part Replacement For Mode
- Page 66 and 67: Section 4 Part Replacement For Mode
- Page 68 and 69: Section 4 Part Replacement For Mode
- Page 70 and 71: Section 4 Part Replacement For Mode
- Page 72 and 73: Section 4 Part Replacement For Mode
- Page 74 and 75: Section 4 Part Replacement For Mode
- Page 76 and 77: Section 4 Part Replacement For Mode
- Page 78 and 79: Section 4 Part Replacement For Mode
- Page 80 and 81: Section 4 Part Replacement For Mode
- Page 82 and 83: Section 4 Part Replacement For Mode
- Page 84 and 85: Section 4 Part Replacement For Mode
- Page 86 and 87: Section 4 Part Replacement For Mode
- Page 88 and 89: Section 4 Part Replacement For Mode
- Page 90 and 91: Section 4 Part Replacement For Mode
- Page 92 and 93: Section 4 Part Replacement For Mode
- Page 94 and 95: Section 4 Part Replacement For Mode
- Page 96 and 97: Section 4 Part Replacement For Mode
- Page 98 and 99: Section 4 Part Replacement For Mode
- Page 102 and 103: Section 5 - Start Up For Models: JG
- Page 104 and 105: Section 5 - Start Up For Models: JG
- Page 106 and 107: Section 5 - Start Up For Models: JG
- Page 108 and 109: Section 5 - Start Up For Models: JG
- Page 110 and 111: Section 5 - Start Up For Models: JG
- Page 112 and 113: Section 6 - Troubleshooting For Mod
- Page 114 and 115: Section 6 - Troubleshooting For Mod
- Page 116 and 117: Appendix A Ariel Fasteners and Torq
- Page 118 and 119: Appendix A Ariel Fasteners and Torq
- Page 120 and 121: Appendix A Ariel Fasteners and Torq
- Page 122 and 123: Appendix B - Clearances For Models:
- Page 124 and 125: Appendix B - Clearances For Models:
- Page 126 and 127: Appendix B - Clearances For Models:
- Page 128 and 129: Appendix C - Frame Specifications F
- Page 130 and 131: Appendix C - Frame Specifications F
- Page 132: Appendix D Compressor Clearance, Oi
Section 4 Part Replacement For Models: JGH:E:K:T<br />
Before piston rod installation, wipe it with denatured alcohol. Be careful not to leave fingerprints on<br />
the rod before it contacts the packing rings. Wipe the rod with denatured alcohol after installation.<br />
Clean the head end head or unloader components with denatured alcohol. Use minimal amounts of<br />
oil for the bolt-holes to ensure oil does not run into the cylinder. Also install the head end steel gasket<br />
without Never-Seez.<br />
Disassemble and clean the valves with denatured alcohol, then re-assemble, wipe them again, and<br />
install. Clean retainers and high clearance assemblies with denatured alcohol. Use only a thin film of<br />
oil for the valve cap O-rings and bolt-holes.<br />
Assemble cleaned parts immediately to avoid contamination and corrosion. If cylinder will not commence<br />
immediate service, contact <strong>Ariel</strong> for preservation instructions to ER-34.<br />
PAGE 4-44 3/11