TCF 100 - Balogh technical center

R/W head
189, rue d'Aubervilliers CP 97 75886 PARIS Cedex18 France
33 (0)1.44.65.65.00 http://www.balogh-rfid.com
33 (0)1.44.65.65.10 contact@balogh-rfid.com
IDENTIFICATION SYSTEMS
TCF 100
GENERAL FEATURES ——————————–———————–——–—————————————————-———————–———–—
TCF 100 is an R/W head allowing to exchange data with tags TAF without contact,
using a protocol compliant with the standards ISO 18000-3 mode 1 and ISO 15693.
It has to be linked up to a Balogh interface, chosen among:
• fieldbus interfaces BI ... FcFc (slave),
• MELS 30 Fc (slave),
• CEPR96 Fc (programmable) and CFER 24Fc,
• MRER 21Fc# or #Fc (station of the Modul .R identification network).
ASSEMBLY DATA ——————————–——–——-——————————–—-———————————————————————————
Assembly using two screws (length under head ≥ 35 mm, right-angled distances: 104 x 65 mm):
transmission zone centre
Connection:
The TCF 100 is fitted with a 5-pin M12 metallic male socket.
Use a corresponding female cable connector (A-coded, ref. 202 274) and a shielded cable with the following characteristics:
• max. length: 50 m,
• overall max. capacity between conductors and shield: 10 nF.
The shield must be in contact to the cable connector housing by a 360° round crimping.
For various possible interfaces, Balogh proposes cables with straight connector(s):
• PUR cordset 3+ de 5 m 2) (ref. 495XXB4512) for BI.. interfaces
(refer to the Accessories corresponding data sheet),
• PUR cable FFMD5/12 (length: 2, 10 or 15 m) for the other interfaces
(refer to the table opposite for wire colours).
The coding peg at 10:30 allows you to plug some right-angled
cable connectors (check to make sure that yours are OK):
1) red in the first models FFMD5/12
2)
10 and 25 m on request
Pin nr Description Wire colour
1 +24VDC brown 1)
2 Output white
3 Input blue
4 0 V black
5 0 V green/yellow

C
H
A
R
A
C
T
E
Functional
TAF 50 TAF 93
direction of travel: longitudinal transversal longitudinal transversal
tag back: isolated isolated against steel isolated against steel
Parameters
Min. Typ. Min. Typ. Min. Typ. Min. Typ. Min. Typ. Min. Typ. unit
S n
"nominal" range 15 100 15 100 25 140 15 65 25 140 15 65 mm
S r
recommended range 0.5 x S n
mm
LS r
length of transmiss. zone @Sr 110 1) 95 2) 135 3) 85 4) 110 5) 60 6) mm
D er
distance betw. TCF end-to-end 330 290 410 310 370 240 mm
D tt
distance betw. TAF end-to-end 330 290 410 310 370 240 mm
Test conditions:
• Tag parallel to the head (tag tilt < 10°).
• No metal round the tag and round the head either.
• Maximum authorised offsets for LSr to reach
at least the published value:
R
I
S
T
I
C
S
General Electron. Power
- angular: 20° (for 3) to 6) )
- lateral :
1) ± 15 mm
2) ± 20 mm
MIN NOM MAX unit
Supply direct voltage (ripple included) 21 24 29 V
Protection against polarity reversal yes -
Supply current @24VDC 90 mA
Protection against short-circuits
yes
Carrier frequency 13.56 MHz
Ambient temperature - 25 + 70 °C
Protection rating IP 65 -
Casing PA 12 (GF30%) -
Weight 550 g
3)
± 20 mm
4)
± 8 mm
5)
± 25 mm
6)
± 10 mm.
A
S
S
E
M
B
L
Y
The head is not to be mounted directly in a recessed metal cavity;
a minimum metal-free clearance is required round the head:
b
R
E
C
O
M
M
E
N
D
A
T
I
O
N
S
a ≥ 30 mm
b ≥ 30 mm
To avoid interference between two TCF 100, there must be a minimum space (D er ) between them
(refer to the above table).
a
BALOGH SA, 189 rue d'Aubervilliers CP97 75886 PARIS Cedex 18 FRANCE 33 (0)1 44 65 65 00 33 (0)1 44 65 65 10
S.A à Directoire au Capital de 800 000 € - R.C.B. PARIS 582 061 073.
Subject to modification.
Ref: F-TCF 100-1.2 - EN