here - Snap-on Equipment
here - Snap-on Equipment here - Snap-on Equipment
Maintenance • Wear safety goggles and protective gloves, user and bystander. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. • Read, understand and follow Safety Information in the front of this manual. 3 Discard the O-rings from the ends of the tubing assemblies. 6. Remove three tubing assemblies from compressor and solenoid assemblies. 7. Remove the compressor retaining nut on the bottom of the plumbing shelf near the front of the unit. 8. Tilt compressor, mounted on hinged compressor plate, out of unit and drain oil into an approved container. Compressor will rest on plumbing shelf edge. Approximately 9 oz of oil should be obtained. 9. Tilt the compressor to the normal upright position. 10. Reinstall the compressor retaining nut. 11. Use plastic bottle supplied with oil change kit to pour 9.3 oz (275 cc) of 3GS compressor oil, part number 681- 0179-2, into input port of compressor. 12. Install new O-rings on the ends of the tubing assemblies. 13. Place a small amount of compressor oil on the O-rings and reinstall the tubing assemblies. 14. Replace the rear cover. High Performance Vacuum Pump (Optional) By having this option vacuum will be performed by the high performance vacuum pump instead of the smaller internal vacuum pump. Check the oil level everyday, if low add the recommended oil until you see the proper level in the oil level sight glass. The oil in the high performance vacuum pump must be changed annually to prolong pump life. The optional oil change kit is recommended. For additional information refer to Replacement Parts in this chapter. All parts necessary to change the vacuum pump oil are included in this kit. 3-8
Maintenance Maintaining the High Performance Vacuum Pump 1. Perform a Recycle on the service hoses. For additional information refer to Chapter 2–Evacuating Service Hoses. 2. Wait for COMPLETED! to display. 3. Turn the power off and unplug your Kool Kare unit from the electrical outlet. 4. Remove the screws holding the rear cover. 5. Remove the rear cover. • Wear safety goggles and protective gloves, user and bystander. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. • Read, understand and follow Safety Information in the front of this manual. 6. Remove the vacuum pump retaining nuts on the bottom of the vacuum pump near the rear of the unit. 7. Tilt the vacuum pump, out of the unit and drain oil into an approved container. 8. Tilt the vacuum pump to the normal upright position. 9. Reinstall the vacuum pump retaining nuts. 10. Use plastic bottle supplied with oil change kit to pour the recommended replacement oil into input port of the vacuum pump. 11. Replace the rear cover. Particle Filter Maintenance T
- Page 4 and 5: Part Number ZEEAC304D Revision A ©
- Page 6 and 7: Safety Information The signal word
- Page 8 and 9: Safety Information Oil (Lubricant)
- Page 10 and 11: Safety Information Risk of injury.
- Page 12 and 13: ii Table of Contents
- Page 14 and 15: Trademark and Copyright Information
- Page 16 and 17: Using This Manual Safety Messages S
- Page 18 and 19: viii Using This Manual
- Page 20 and 21: Introduction Refrigerant Gases Halo
- Page 22 and 23: Introduction Refrigerant Substitute
- Page 24 and 25: Introduction Functional Description
- Page 26 and 27: Introduction Back View Figure 1-2:
- Page 28 and 29: Introduction Particle Filter Assemb
- Page 30 and 31: Introduction Language Selection Wit
- Page 32 and 33: 1-14 Introduction
- Page 34 and 35: Installation and Operation 3. Conne
- Page 36 and 37: Installation and Operation Adding R
- Page 38 and 39: Installation and Operation Operatio
- Page 40 and 41: Installation and Operation Connecti
- Page 42 and 43: Installation and Operation — If t
- Page 44 and 45: Installation and Operation Charge O
- Page 46 and 47: Installation and Operation Removing
- Page 48 and 49: Maintenance Maintaining the Oil Sep
- Page 50 and 51: Maintenance Master Filter The maste
- Page 52 and 53: Maintenance Changing the Master Fil
- Page 56 and 57: Maintenance Figure 3-4: Particle Fi
- Page 58 and 59: Maintenance Symptom Possible Cause
- Page 60: 3-14 Maintenance
Maintenance<br />
• Wear safety goggles and protective gloves, user<br />
and bystander. Everyday eyeglasses <strong>on</strong>ly have<br />
impact resistant lenses, they are NOT safety<br />
glasses.<br />
• Read, understand and follow Safety Informati<strong>on</strong> in<br />
the fr<strong>on</strong>t of this manual.<br />
3 Discard the O-rings from the ends of the tubing<br />
assemblies.<br />
6. Remove three tubing assemblies from compressor and<br />
solenoid assemblies.<br />
7. Remove the compressor retaining nut <strong>on</strong> the bottom of<br />
the plumbing shelf near the fr<strong>on</strong>t of the unit.<br />
8. Tilt compressor, mounted <strong>on</strong> hinged compressor plate,<br />
out of unit and drain oil into an approved c<strong>on</strong>tainer.<br />
Compressor will rest <strong>on</strong> plumbing shelf edge.<br />
Approximately 9 oz of oil should be obtained.<br />
9. Tilt the compressor to the normal upright positi<strong>on</strong>.<br />
10. Reinstall the compressor retaining nut.<br />
11. Use plastic bottle supplied with oil change kit to pour 9.3<br />
oz (275 cc) of 3GS compressor oil, part number 681-<br />
0179-2, into input port of compressor.<br />
12. Install new O-rings <strong>on</strong> the ends of the tubing assemblies.<br />
13. Place a small amount of compressor oil <strong>on</strong> the O-rings<br />
and reinstall the tubing assemblies.<br />
14. Replace the rear cover.<br />
High Performance Vacuum Pump (Opti<strong>on</strong>al)<br />
By having this opti<strong>on</strong> vacuum will be performed by the high<br />
performance vacuum pump instead of the smaller internal<br />
vacuum pump. Check the oil level everyday, if low add the<br />
recommended oil until you see the proper level in the oil level<br />
sight glass. The oil in the high performance vacuum pump must<br />
be changed annually to prol<strong>on</strong>g pump life. The opti<strong>on</strong>al oil<br />
change kit is recommended. For additi<strong>on</strong>al informati<strong>on</strong> refer to<br />
Replacement Parts in this chapter. All parts necessary to<br />
change the vacuum pump oil are included in this kit.<br />
3-8