here - Snap-on Equipment
here - Snap-on Equipment here - Snap-on Equipment
Installation and Operation Charge Only Program — If t
Installation and Operation Displaying Refrigerant Amount Tank Full/Empty Your Kool Kare unit verifies t
- Page 1: USER’S MANUAL Kool Kare
- Page 4 and 5: Part Number ZEEAC304D Revision A ©
- Page 6 and 7: Safety Information The signal word
- Page 8 and 9: Safety Information Oil (Lubricant)
- Page 10 and 11: Safety Information Risk of injury.
- Page 12 and 13: ii Table of Contents
- Page 14 and 15: Trademark and Copyright Information
- Page 16 and 17: Using This Manual Safety Messages S
- Page 18 and 19: viii Using This Manual
- Page 20 and 21: Introduction Refrigerant Gases Halo
- Page 22 and 23: Introduction Refrigerant Substitute
- Page 24 and 25: Introduction Functional Description
- Page 26 and 27: Introduction Back View Figure 1-2:
- Page 28 and 29: Introduction Particle Filter Assemb
- Page 30 and 31: Introduction Language Selection Wit
- Page 32 and 33: 1-14 Introduction
- Page 34 and 35: Installation and Operation 3. Conne
- Page 36 and 37: Installation and Operation Adding R
- Page 38 and 39: Installation and Operation Operatio
- Page 40 and 41: Installation and Operation Connecti
- Page 42 and 43: Installation and Operation — If t
- Page 46 and 47: Installation and Operation Removing
- Page 48 and 49: Maintenance Maintaining the Oil Sep
- Page 50 and 51: Maintenance Master Filter The maste
- Page 52 and 53: Maintenance Changing the Master Fil
- Page 54 and 55: Maintenance • Wear safety goggles
- Page 56 and 57: Maintenance Figure 3-4: Particle Fi
- Page 58 and 59: Maintenance Symptom Possible Cause
- Page 60: 3-14 Maintenance
Installati<strong>on</strong> and Operati<strong>on</strong><br />
Displaying Refrigerant Amount<br />
Tank Full/Empty<br />
Your Kool Kare unit verifies t<str<strong>on</strong>g>here</str<strong>on</strong>g> is enough refrigerant<br />
in tank to charge.<br />
— If t<str<strong>on</strong>g>here</str<strong>on</strong>g> is enough refrigerant, the C<strong>on</strong>necti<strong>on</strong> Check<br />
screen displays.<br />
— If t<str<strong>on</strong>g>here</str<strong>on</strong>g> is not enough refrigerant, the following<br />
message displays for five sec<strong>on</strong>ds, then the<br />
Charging screen displays:<br />
CHARGE AMOUNT SELECTED IS GREATER THAN<br />
‘CHARGEABLE’ IN TANK!<br />
3 For additi<strong>on</strong>al informati<strong>on</strong> refer to Adding Refrigerant<br />
to Kool Kare in this chapter.<br />
8. Select CONTINUE. The following messages display:<br />
PURGING AIR FROM TANK...PLEASE WAIT<br />
CHARGE SEQUENCE! WAITING FOR STABLE SCALE!<br />
CHARGE SEQUENCE! I AM CHARGING!<br />
3 Select HOLD to pause the charging sequence. Select<br />
CONTINUE to resume charging.<br />
COMPLETED!<br />
The procedure is complete when your Kool Kare unit<br />
beeps twice.<br />
Use this procedure to determine the amount of refrigerant in the<br />
recovery tank and the amount able to be charged.<br />
1. Select AMOUNT key. The Recovery Tank screen<br />
displays for five sec<strong>on</strong>ds.<br />
2. Select POUNDS or KGS to select a unit of measure.<br />
Read recovery tank weight.<br />
3. Select CHARGEABLE. The Chargeable screen displays<br />
for five sec<strong>on</strong>ds.<br />
4. Select POUNDS or KGS to select a unit of measure.<br />
Read amount.<br />
Messages display when the recovery tank is full or empty.<br />
3 The unit may be used to vacuum or charge an A/C<br />
system even when the recovery tank is full.<br />
2-13