ToneLab LE's manual - Vox
ToneLab LE's manual - Vox
ToneLab LE's manual - Vox
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
CONTROL SWITCH SETTINGS<br />
You can make the following control switch settings<br />
independently for each program.<br />
Press the EXP-CTL-CHAIN button to make it<br />
blink, and use value knob 4 to select the effect<br />
you want to control.<br />
SWITCHING EACH EFFECT ON/OFF<br />
make the name display read “FACTOR”.<br />
Here you can specify the proportion of<br />
SPEED or TIME in relation to the interval of<br />
your taps. For example if you set DLY TAP<br />
as the target, and FACTOR to “1-4,” the<br />
delay time will be set to 1/4th of the duration<br />
between taps.<br />
5. Press the EXIT/TUNE button to return to the<br />
mode you were in.<br />
• “I/ONOFF”<br />
• “P/ONOFF”<br />
• “A/ONOFF”<br />
• “AC/ONOFF”<br />
• “C/ONOFF”<br />
• “M/ONOFF”<br />
• “D/ONOFF”<br />
• “R/ONOFF”<br />
NOTE: The CONTROL switch LEDs indicate the on/<br />
off status.<br />
USING TAP TEMPO TO SET A<br />
PARAMETER<br />
• “MOD TAP”<br />
• “DLY TAP”<br />
NOTE: The CONTROL switch LED will blink at the<br />
tempo you specify.<br />
EFFECT CONTROL<br />
• “FLN TRIG”<br />
• “ROT SPD”<br />
• “HOLD DLY”<br />
External effect insertion on/off<br />
Pedal effect on/off<br />
Amp model on/off<br />
Links the Amp model on/off status<br />
to the Cabinet model on/off<br />
Cabinet effect on/off<br />
Modulation effect on/off<br />
Delay effect on/off<br />
Reverb effect on/off<br />
Use TAP TEMPO to set the<br />
SPEED parameter of the modulation<br />
effect<br />
Use TAP TEMPO to set the<br />
TIME parameter of the delay<br />
effect<br />
LFO START TRIGGER of the<br />
CLASSIC FLANGER effect<br />
SPEED SW of the ROTARY<br />
effect<br />
HOLD of the HOLD DELAY<br />
effect<br />
NOTE: If you haven’t selected an applicable effect,<br />
nothing will be controlled.<br />
1. Press the EXP-CTL-CHAIN button to make<br />
it blink.<br />
2. To display the control target, press the ®<br />
button four times.<br />
3. To select the control target, use the ▲, ▼<br />
buttons or turn value knob 4.<br />
4. If you’ve selected MOD TAP or DLY TAP,<br />
press the ® button or turn value knob 5 to<br />
FACTOR VALUE KNOB 5 SETTING<br />
If the MODULATION effect’s SPEED parameter<br />
or the DELAY effect’s TIME parameter are<br />
assigned to a control switch, you can set the<br />
MODULATION effect’s LFO SPEED or the<br />
DELAY effect’s DELAY TIME by the interval at<br />
which you press the control switch twice. When<br />
you do so, the interval at which you actually<br />
press the pedal will be applied to the parameter<br />
at a “factor” (i.e., multiple) of 1/6, 1/4, 1/3, 1/2, 2/<br />
3, 3/4, 1, 4/3, 3/2, 2, 3, or 4, according to the setting<br />
of the FACTOR parameter (value knob 5).<br />
NOTE: The maximum spacing of your taps can be no<br />
more than ten seconds.<br />
NOTE: If you’ve assigned a parameter other than<br />
MOD TAP or DLY TAP, the FACTOR setting<br />
does nothing.<br />
NOTE: If you change the control switch setting, the<br />
FACTOR parameter is reset to “1.”<br />
Tuner<br />
Pedals<br />
MIDI/DIGITAL<br />
Factory<br />
settings<br />
Troubleshooting<br />
Spec.<br />
Program<br />
List<br />
49