ToneLab SE Owner's manual - Vox
ToneLab SE Owner's manual - Vox ToneLab SE Owner's manual - Vox
1. CLASSIC CHORUS (CL CHORUS) MONO IN/MONO OUT 1 (MODE=1,3) MONO IN/MONO OUT 3 (MODE=2) This models a chorus unit that has two modes (chorus and vibrato), and is bestknown for being built into a guitar amp. There’s no parameter to switch between chorus and vibrato, but you can use the SPEED and DEPTH knobs to create either of these sounds, giving you an even broader range of possibilities than the original unit! The output vibrato mode allows you to create vibrato (pitch modulation) by outputting just the effect sound. [1] “SPEED” 0.100–10.00 [Hz] * Adjusts the modulation speed. [2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth. [4] “MANUAL” 1.0–10.0 * Adjusts the center frequency of the sweep. If DEPTH is set to 10, MANUAL will not function. [5] “MODE” 1, 2, 3 Selects the output mode. 1: Mono output. 2: Stereo mode in which the effect is panned right, and the dry sound panned left. 3: Vibrato mode, in which only the effect sound is output. Setting MANUAL to 10 will minimize the delay of the output sound. 2. STEREO CHORUS (ST CHORUS) MONO IN/STEREO OUT 1 A stereo chorus in a yellow case. A sense of stereo is created by inverting the phase of the effect sound for the right output, producing a feeling of spaciousness that is somewhat different than the stereo effect of CLASSIC CHORUS. [1] SPEED 0.100–10.00 [Hz] * Adjusts the modulation speed. [2] DEPTH 0.0–10.0 * Adjusts the modulation depth. [3] MANUAL 1.0–10.0 * Adjusts the center frequency of the sweep. If DEPTH is set to 10, MANUAL will not function. [6] MIX 0.0–10.0 * Adjusts the mix amount of the effect sound. 3. CLASSIC FLANGER (CL FLANG) MONO IN/MONO OUT 1 A model of a truly classic analogue flanger that “unchained” a highly influential modern guitarist who many hail as the “godfather of two handed tapping.” [1] “SPEED” 0.100–10.00 [Hz] * Adjusts the modulation speed. [2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth. [3] “RESO” 0.0–10.0 * Adjusts the amount of resonance. [4] “MANUAL” 1.0–10.0 * Adjusts the center frequency of the sweep. If DEPTH is set to 10, MANUAL will not function. [5] “OFFSET” 0.0–10.0 Adjusts the starting position of the LFO. If you assign “FLN TRIG” to a control pedal, the LFO will be reset to the starting position specified by OFF- SET whenever you operate the control pedal. When you defeat BYPASS, the LFO will start from the position you specify here. (p.56 Control pedal settings) 40
[6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound. CONTROL pedal If you set the FLN TRIG: CONTROL pedal setting to “FLN TRIG,” the LFO will be reset to the position specified by OFFSET whenever you operate the pedal. (p.56 Control pedal settings) 4. BI CHORUS MONO IN/MONO OUT 1 (MODE=S) STEREO IN/ STEREO OUT 1 (MODE=P1, P2, P3) This is a chorus model unique to ToneLabSE. It provides two chorus units, CHO- RUS 1 and CHORUS 2, and lets you connect the two units not only in series or in parallel, but also to synchronize or de-synchronize the two LFOs. It produces a variety of tones that cover a range from wonderfully spacious sounds to bizarre flanger-like sounds with complex modulation. [1] “SPEED 1” 0.100–10.00 [Hz] * Adjusts the modulation speed of CHORUS 1. [2] “DEPTH” 0.0–10.00 * Adjusts the modulation depth of CHORUS 1/2. [3] “RESO” 0.0–10.0 * Adjusts the amount of resonance for CHORUS 1/2. [4] “SPEED 2” 0.100–10.00 [Hz] * Adjusts the modulation speed of CHORUS 2. NOTE: This will not function if MODE is set to P2 or P3. [5] “MODE” S/P1/P2/P3 Specifies the connection and LFO for CHORUS 1/2. S: CHORUS 1/2 are connected in series. P1: CHORUS 1/2 are connected in parallel. P2: CHORUS 1/2 are connected in parallel, and their LFOs are synchronized. P3: CHORUS 1/2 are connected in parallel, and their LFOs are synchronized in opposite phase (Stereo mode). NOTE: If P2 or P3 is selected, the speed is adjusted by the SPEED 1 knob. [6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound. 5. DUO PHASE (DUO PHAS) MONO IN/MONO OUT 2 (MODE=S1, S2) STEREO IN/STEREO OUT 2 (MODE=P1, P2, P3) This is an amazing phaser that provides two six-stage phasers; PHASER 1 and PHASER 2. They can be connected in series (to make a pseudo-twelve-stage phaser!) or in parallel, and you can also synchronize or de-synchronize the two LFOs. [1] “SPEED 1” 0.100–10.00 [Hz] * Adjusts the modulation speed of PHASER 1. [2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth of PHASER 1/2. [3] “RESO” 0.0–10.0 * Adjusts the amount of resonance for PHASER 1/2. [4] “SPEED 2” 0.100–10.00 [Hz] * Adjusts the modulation speed of PHASER 2. NOTE: This will not function if MODE is set to S2, P2, or P3. REVERB DELAY MODULATION PEDAL CABINET AMP TYPE Amp/Effect TYPE 41
- Page 1 and 2: Owner's Manual E 1
- Page 3 and 4: CE mark for European Harmonized Sta
- Page 5 and 6: ▼ buttons to select “Ln” (LIN
- Page 7 and 8: 15. ToneLabSE provides a PEDAL effe
- Page 9 and 10: Program Select mode ...............
- Page 11 and 12: Introduction WELCOME ABOARD! Many t
- Page 13 and 14: Apart from the vital valve tone thi
- Page 15 and 16: A Guitarist’s Guided Panel Tour H
- Page 17 and 18: 2 1.9 REVERB selector This selects
- Page 19 and 20: 3.8 Name display Displays program n
- Page 21: REAR PANEL 10 11 POWER SUPPLY 10.1
- Page 24 and 25: MIC1 -10dBV MIC GAIN U 10 60 +10dB
- Page 26 and 27: Playing ToneLabSE PROGRAM SELECT MO
- Page 28 and 29: ACTIVATING OR DEACTIVATING THE KEY
- Page 30 and 31: 6. Use the CABINET model selector t
- Page 32 and 33: STORING A PROGRAM When your tweakin
- Page 34 and 35: model. This time though, the “neu
- Page 36 and 37: no feedback” emulation whenever A
- Page 38 and 39: Original’s valve compliment: 5 x
- Page 40 and 41: emains focused and well defined at
- Page 42 and 43: B. CABINET MODELS Now let’s look
- Page 44 and 45: It is renowned for its deep bass an
- Page 46 and 47: [1] “SENS” 1.0...10.0 Adjusts t
- Page 48 and 49: WARNING! Like all pedals of this ty
- Page 52 and 53: [5] “MODE” S1, S2, P1, P2, P3 6
- Page 54 and 55: 10. FILTRON STEREO IN/STEREO OUT 2
- Page 56 and 57: 2. MULTI HEAD (MULTI HD) MONO IN/MO
- Page 58 and 59: 10. HOLD DELAY (HOLD DLY) MONO IN/M
- Page 60 and 61: 11. GATE MONO IN/STEREO OUT 1 This
- Page 62 and 63: CALIBRATING THE TUNER When you swit
- Page 64 and 65: SETTING THE EXPRESSION TARGET Here
- Page 66 and 67: “EXP1INIT” lets you specify whe
- Page 68 and 69: 5. Slowly advance the expression pe
- Page 70 and 71: SETTING THE MIDI CHANNEL (GLOBAL
- Page 72 and 73: 1. Press the GLOBAL button (3.4). 2
- Page 74 and 75: Restoring the Factory Preset Progra
- Page 76 and 77: 4. You’re using the ACOUSTIC peda
- Page 78 and 79: Program list NAME PEDAL Ach-AMP Ach
- Page 80 and 81: TOP PANEL: 1.2 1.4 5 1.5 1.3 1.6 1.
- Page 82: Owner's Manual E 1 2003 VOX AMPLIFI
[6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound.<br />
CONTROL pedal<br />
If you set the FLN TRIG: CONTROL pedal setting<br />
to “FLN TRIG,” the LFO will be reset to the position<br />
specified by OFF<strong>SE</strong>T whenever you operate<br />
the pedal. (p.56 Control pedal settings)<br />
4. BI CHORUS MONO IN/MONO OUT 1 (MODE=S) STEREO IN/<br />
STEREO OUT 1 (MODE=P1, P2, P3)<br />
This is a chorus model unique to <strong>ToneLab</strong><strong>SE</strong>. It provides two chorus units, CHO-<br />
RUS 1 and CHORUS 2, and lets you connect the two units not only in series or in<br />
parallel, but also to synchronize or de-synchronize the two LFOs. It produces a<br />
variety of tones that cover a range from wonderfully spacious sounds to bizarre<br />
flanger-like sounds with complex modulation.<br />
[1] “SPEED 1” 0.100–10.00 [Hz] * Adjusts the modulation speed of CHORUS 1.<br />
[2] “DEPTH” 0.0–10.00 * Adjusts the modulation depth of CHORUS 1/2.<br />
[3] “RESO” 0.0–10.0 * Adjusts the amount of resonance for CHORUS<br />
1/2.<br />
[4] “SPEED 2” 0.100–10.00 [Hz] * Adjusts the modulation speed of CHORUS 2.<br />
NOTE: This will not function if MODE is set to P2 or P3.<br />
[5] “MODE” S/P1/P2/P3 Specifies the connection and LFO for CHORUS<br />
1/2.<br />
S: CHORUS 1/2 are connected in series.<br />
P1: CHORUS 1/2 are connected in parallel.<br />
P2: CHORUS 1/2 are connected in parallel, and<br />
their LFOs are synchronized.<br />
P3: CHORUS 1/2 are connected in parallel, and<br />
their LFOs are synchronized in opposite<br />
phase (Stereo mode).<br />
NOTE: If P2 or P3 is selected, the speed is adjusted by the SPEED 1<br />
knob.<br />
[6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound.<br />
5. DUO PHA<strong>SE</strong> (DUO PHAS) MONO IN/MONO OUT 2 (MODE=S1,<br />
S2) STEREO IN/STEREO OUT 2 (MODE=P1, P2, P3)<br />
This is an amazing phaser that provides two six-stage phasers; PHA<strong>SE</strong>R 1 and<br />
PHA<strong>SE</strong>R 2. They can be connected in series (to make a pseudo-twelve-stage<br />
phaser!) or in parallel, and you can also synchronize or de-synchronize the two<br />
LFOs.<br />
[1] “SPEED 1” 0.100–10.00 [Hz] * Adjusts the modulation speed of PHA<strong>SE</strong>R 1.<br />
[2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth of PHA<strong>SE</strong>R 1/2.<br />
[3] “RESO” 0.0–10.0 * Adjusts the amount of resonance for PHA<strong>SE</strong>R<br />
1/2.<br />
[4] “SPEED 2” 0.100–10.00 [Hz] * Adjusts the modulation speed of PHA<strong>SE</strong>R 2.<br />
NOTE: This will not function if MODE is set to S2, P2, or P3.<br />
REVERB DELAY MODULATION PEDAL CABINET AMP TYPE Amp/Effect<br />
TYPE<br />
41