Download - Bytemark Hosting
Download - Bytemark Hosting Download - Bytemark Hosting
2 Block Diagram Anders Electronics plc (Anders) does not warrant the accuracy or completeness of the information contained herein, the supply of products by Anders is subject to its standard terms and conditions of sale. Prior to concluding any agreement with Anders the customer should satisfy itself of the accuracy and completeness of the information contained herein and should notify to Anders any intended use of the product. www.anders.co.uk | Info@anders.co.uk Page 6 of 21
3 I/O Connectors J1 P12 DC Power Jack RS232 Connector (ultra mini format) P8 USB-OTG Connector (mini USB type A/B) P17 Dual USB Host Connector (Standard Type A) P18 Core Ethernet Connector (RJ45) P16 Base Ethernet Connector (RJ45) J3 Mono Audio Input (standard 3.5mm Jack) J4 Stereo Headphone Output (standard 3.5mm Jack) P10 Keypad FPC Connector SW2 Reset Button – Cold reset to the system (Tactile switch) P5 Battery Connector LEDs LED Colour System LED activity (DS1, DS2, DS3) DS1 Green Power Indicates that the 3.3V rail is active DS2 Red Charger Indicates that the battery connected to P5 is being charged DS3 Green Power Indicates that the 3.8V rail is active E1 Jumper E2 Jumper E3 Jumper E4 Jumper E7 Jumper E8 Jumper Battery Charger Disable Jumper 1-2 - Main Battery Charging is disabled. NC - Main Battery Charging is enabled (if a battery is connected to P5, and DC supply is connected to J1. Input Power Selector 1-2 System main power source in a DC supply through J1 connector 2-3 System main power source is a battery connected to connector P5 NC power off Controls the current output of USB1 (P17 bottom) 1-2 P17 is supplied by 5V DC. Output current limited up to 500mA 2-3 P17 is supplied by charge pump. Output current limited up to 100mA NC P17 is not supplied with 5V Controls the current output of USB2 (P17 top) 1-2 P17 is supplied by 5V DC. Output current limited up to 500mA 2-3 P17 is supplied by charge pump. Output current limited up to 100mA NC P17 is not supplied with 5V RTC backup 1-2 RTC back-up is enabled NC Backup battery is disconnected. RTC backup disabled Display Interface Power Selector 1-2 Display interface operate at 1.8V voltage level 2-3 Display interface operate at 3.3V voltage level NC Display interface is not powered Anders Electronics plc (Anders) does not warrant the accuracy or completeness of the information contained herein, the supply of products by Anders is subject to its standard terms and conditions of sale. Prior to concluding any agreement with Anders the customer should satisfy itself of the accuracy and completeness of the information contained herein and should notify to Anders any intended use of the product. www.anders.co.uk | Info@anders.co.uk Page 7 of 21
- Page 1 and 2: DX4 Series Embedded Multitouch Disp
- Page 3 and 4: Table of Content 1 Specification ..
- Page 5: Other Interfaces Operating System P
- Page 9 and 10: 4 Mechanical Information (All Dimen
- Page 11 and 12: 4.2.2 DX4K3730-43A and DX4P3730-43A
- Page 13 and 14: 4.3 Open Frame Assembled DX4 with 7
- Page 15 and 16: 4.5 Open Frame Assembled DX4 with 4
- Page 17 and 18: 6 Evaluation Kit Contents • 1 x Q
- Page 19 and 20: 7.2 DX4 Non Assembled Product Order
- Page 21: 8 Support Resources Dedicated wiki
2 Block Diagram<br />
Anders Electronics plc (Anders) does not warrant the accuracy or completeness of the information contained herein, the supply of products by Anders is<br />
subject to its standard terms and conditions of sale. Prior to concluding any agreement with Anders the customer should satisfy itself of the accuracy and<br />
completeness of the information contained herein and should notify to Anders any intended use of the product. www.anders.co.uk | Info@anders.co.uk<br />
Page 6 of 21
Change language